Which air dam?
07-26-2007, 03:18 PM
#1
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Jul 2004
Location: Calgary, AB, Canada
Posts: 10,763
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Which air dam?
I forget, which air dam is *supposed* to go on my car? '82 TA?
It was long gone when I bought the car.
I was going to buy a 1 piece one from classic industries, but they couldn't get it into a box to ship to Canada. Ya know, we only allow boxes under a certain size to fit through that tight border squeeze
Anyway, can I use a 3 piece one? Is it "correct" for my car, and if not, can I drill a few holes and make it fit? Or is the panel that it would bolt to non-existent, and i'd be wasting my time?
Thanks
It was long gone when I bought the car.
I was going to buy a 1 piece one from classic industries, but they couldn't get it into a box to ship to Canada. Ya know, we only allow boxes under a certain size to fit through that tight border squeeze
Anyway, can I use a 3 piece one? Is it "correct" for my car, and if not, can I drill a few holes and make it fit? Or is the panel that it would bolt to non-existent, and i'd be wasting my time?
Thanks
07-26-2007, 11:50 PM
#2
Senior Member
iTrader: (1)
Join Date: May 2007
Location: Newport Beach, Ca.
Posts: 666
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Iroc
Engine: 383 TPI
Transmission: 700r4
Axle/Gears: BW 9 bolt 3.27
Re: Which air dam?
Are you kidding me? Too big? I used to ship all over the world with no problems, boxes/crates up to 8' x 10'. Check out some of the vendors that help sponsor this site, I am sure you can find what you need. My Hawks catalog lists a 3 piece for your car. I have bought from them before so I know they can lick a stamp. Part # GM-5557 $100.00 + shipping.
07-27-2007, 12:18 AM
#3
Senior Member
Join Date: Nov 2006
Posts: 455
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1984 Trans Am
Engine: Built chevy 350
Transmission: TCI Built 700r4
Axle/Gears: 3.73 posi 10 bolt
Re: Which air dam?
If you have ground FX you need the one piece...I just went through the same situation trying to find out if I need the one peice or 3 piece. Here is a pic of the front of my car...if you dont have the front spoiler like mine you need a 3 piece.
Last edited by 4playta; 10-18-2007 at 04:29 AM.
07-27-2007, 09:29 AM
#4
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Jul 2004
Location: Calgary, AB, Canada
Posts: 10,763
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Re: Which air dam?
I don't have a front spoiler like that one.
Excellent, i'll grab the 3 piece then, and see how it works for me.
modern day muscle wanted $40 or so for it, so i'm going for that.
Thanks
Excellent, i'll grab the 3 piece then, and see how it works for me.
modern day muscle wanted $40 or so for it, so i'm going for that.
Thanks
Thread
Thread Starter
Forum
Replies
Last Post
