What tool for high side shrader valve replacement? - Third Generation F-Body Message Boards


Go Back   Third Generation F-Body Message Boards > Tech Boards > Cooling
Search

Cooling Discuss all of the aspects of cooling that you can think of! Radiators, transmissions, electric fans, etc.

What tool for high side shrader valve replacement?

Reply
 
Thread Tools Search this Thread
Old 08-28-2011, 11:54 AM   #1
Supreme Member
iTrader: (9)
 
3rdgenmaro's Avatar
 
Join Date: Dec 2004
Location: Lincolnton, NC
Posts: 1,777
Car: 88 IROC
Engine: 97 5.7 Vortec LT4 hotcam
Transmission: 700 r4
Axle/Gears: 3.73


What tool for high side shrader valve replacement?

On a 90 RS Camaro, Im having problems getting the high side schrader valve to seal. The shrader valve tool that I have will fit on the low side, but not the high side. It appears to be much deeper in.

Can anyone point me in the right direction?
__________________
88 Camaro, 97 5.7 vortec, lt4 hotcam, 4160 Holley 600, Pro Built 700r4, 3.73, junk converter
85 S10, 350/350, 10.5:1, Dart Pro1 200Ps, 244/249@50, .565/.543, Air-Gap, 650 DP, 3000 stall, 8.8 with 3.55s
67 SS Chevelle, 396, 4 speed, 3.73

Last edited by 3rdgenmaro; 08-29-2011 at 08:06 AM.
3rdgenmaro is offline vBGarage Page   Reply With Quote
Old 08-28-2011, 01:11 PM   #2
Senior Member
 
Join Date: Jan 2009
Location: DE
Posts: 605
Car: 1990 Firebird Formula
Engine: LB9 - 5.0 TPI
Transmission: 700R4
Axle/Gears: 2.73, LSD

Re: What tool for high side shrader valve replacement?

I used a tool found in a special kit for these at school.
Mr Froman is offline vBGarage Page   Reply With Quote
Old 08-29-2011, 06:39 AM   #3
Supreme Member
iTrader: (9)
 
3rdgenmaro's Avatar
 
Join Date: Dec 2004
Location: Lincolnton, NC
Posts: 1,777
Car: 88 IROC
Engine: 97 5.7 Vortec LT4 hotcam
Transmission: 700 r4
Axle/Gears: 3.73


Re: What tool for high side shrader valve replacement?

anyway you can get me a picture?

I dont need the real expensive ones that allow you to pull the valve without evacuating the system. I already have an empty system. I just need the tool to remove the valve and to replace it. Nothing fancy, I just dont know what I need.
__________________
88 Camaro, 97 5.7 vortec, lt4 hotcam, 4160 Holley 600, Pro Built 700r4, 3.73, junk converter
85 S10, 350/350, 10.5:1, Dart Pro1 200Ps, 244/249@50, .565/.543, Air-Gap, 650 DP, 3000 stall, 8.8 with 3.55s
67 SS Chevelle, 396, 4 speed, 3.73
3rdgenmaro is offline vBGarage Page   Reply With Quote
Old 08-31-2011, 06:06 AM   #4
Supreme Member
iTrader: (9)
 
3rdgenmaro's Avatar
 
Join Date: Dec 2004
Location: Lincolnton, NC
Posts: 1,777
Car: 88 IROC
Engine: 97 5.7 Vortec LT4 hotcam
Transmission: 700 r4
Axle/Gears: 3.73


Re: What tool for high side shrader valve replacement?

If anyone ever runs into the same problem, the tool required is one for R134a schrader valve.

Even though the car is R12 and came from the factory R12, the low side schrader is the only one that a R12 tool will fit. The high side requires the R134a tool, even though it doesnt have the R134a quick connect connection.

One of the odd things that happens over the years I guess.
3rdgenmaro is offline vBGarage Page   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
[NY] PCM,Hypertech chip, Fuel sender, MAF, Shifter, Valve covers NBrehm Engine/Drivetrain/Suspension Parts for Sale 1 08-25-2015 11:49 PM
Will this spring compressor work? TheExaminer Suspension and Chassis 21 08-25-2015 07:34 PM
Missing diverter valve? lakeffect2 Cooling 11 08-23-2015 08:44 AM
Hard Knocking back around the 6th Cylinder db057 Tech / General Engine 4 08-22-2015 08:17 PM
Help with AC recharge refill jackhammer Cooling 6 08-15-2015 10:04 PM


Go Back   Third Generation F-Body Message Boards > Tech Boards > Cooling

Tags
1990, 97, camaro, high, low, r12, r134, r134a, replace, replacement, s10, schrader, side, tool, valve

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -5. The time now is 08:46 AM.


All content copyright 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.