IWANNAROCAGAIN

I have a ton of parts I need to sell, cleaning out storage and all parts must go. I have the following listed parts as well as others not listed, so feel free to email with needs and I'll check if I have it.

Small Block Chevy parts:
Vortec Holley Stealth Ram intake manifold, brand new never used = $375
Tall center bolt SBC aluminum valve covers = $100
New Aluminum SBC 2-piece design Timing Cover = $60
New Aluminum SBC Oil Pan = $75
Full Roller Rockers Self-aligning SBC 1.5 ratio, slightly used for 200 miles = $125

Corvette C4 113 Bare Aluminum Cylinder Heads from 91 C4 = $200 for the pair
Corvette C4 TPI lower intake base, started to port = $50
Corvette C4 TPI Upper Plenum Speed Density, ported for up to 58mm Throttle Body = $125
Corvette C4 Exhaust Manifolds = $75 for pair
Corvette/Camaro TPI Runners stock = $75 for pair
Rebuilt 700R4 transmission from 91 Camaro with 2,500 miles, trans-go shift kit, sonomex pistons, corvette servo, aluminum pan with drain plug, all parts used were recommended from Dana at Pro-Built Transmissions = $800.00

82-92 Camaro Ferrari Style Rear Spoiler Brand new = $125
82-92 Camaro rear rims 90-92 style = $25 each
90-92 Style Center Caps for Rims = $25 Each
85-92 Camaro TPI intake base stock = $50
87-92 Camaro SBC small cap Distributor with Accel Cap and Rotor = $75
82-92 SBC Front Timing Cover with new crank seal = $25
82-92 Rear end 2:73 gears, drum brakes = $75


Alpine CD Radio with Front USB and Sirius/Pandora capability = $50
5.25 Infinity Kappa Speakers = $50/pair
10" Rockford Fosgate Slim Design/low profile Subwoofers = $75 each


Corvette C6 LS2 243 Cylinder Heads Stock = $400 for pair
Fast 102 Intake Manifold for Cathedral Port LS Heads = $750
Corvette C6 LS3 Camshaft Stock brand new take off = $100

Feel free to email with any questions or request pics, I will update list with additional parts when I have time. Thanks for looking.

apie2546

Do you have the actual part number for the Alpine radio? I need to check to make sure it'll work in my setup

Chiknhawk

iTrader: (2)

Pics of the heads

abray1

Price on vortec Holley stealth ram shipped to malvern, AR 72104

ThirdGen1984

iTrader: (1)

pics of the rims?

IWANNAROCAGAIN

It's CDE-124SXM, I think I may also have the power pack that boosts the output of this to 45w/channel. Let me know, thanks

IWANNAROCAGAIN

PM sent

IWANNAROCAGAIN

Which set of heads the 113's or the 243 LS?


Thanks

IWANNAROCAGAIN

I'll take a few in the morning tomorrow and post.

Steve Mack

iTrader: (5)

Did you build the 700R4 or did you have a trans shop do the work?

IWANNAROCAGAIN

I did the work, been a mechanic for almost 20 years, all the parts utilized for the rebuild were suggested from Dana at Probuilt. Trans was redone in the fall of 2010, probably may even have all the receipts for the parts.

IWANNAROCAGAIN

:bump:

The Eager Teen

iTrader: (4)

Any pictures of the 113 heads?

armybyrd

iTrader: (4)

What brand are the roller rockers?

IWANNAROCAGAIN

Sorry Sold

IWANNAROCAGAIN

Yes, its actually easier for me to send pics through email or by text. I'll get a few pics of them tomorrow morning.


Thanks

IWANNAROCAGAIN

IWANNAROCAGAIN

jamon8

iTrader: (3)

how much for the heads shipped to 62966
113

IWANNAROCAGAIN

Probably will be around $40-$50, apparently Fedex jacked their prices up significantly since the last time I've used them.

Let me know
Thanks

IWANNAROCAGAIN

i can upload pics from my phone, just let me know what pics you want and I will get them on here as soon as I can

IWANNAROCAGAIN

Bump

IWANNAROCAGAIN

Daily bump

IWANNAROCAGAIN

bump

IWANNAROCAGAIN

GFusick

How to ship to California the 113 heads ?

IWANNAROCAGAIN

Do you have access to greyhound? That shipping method would be the cheapest, otherwise it will probably run about $50-$60 due to the weight, each head is about 20-25lbs

Let me know thanks

IWANNAROCAGAIN

Bump

IWANNAROCAGAIN

Daily bump

Necron

iTrader: (1)

Are the front calipers for sale? I don't seem them listed. What do you have etc.? Are you selling a front upgrade kit?

Lasroc90

I need the hard plastic lines that go from throttle body to evap, pressure regulator to plenum, etc. All my hard lines were melted in a underhood fire.

IWANNAROCAGAIN

Sold the fronts last night, only have the rears right now, may have a set of fourth generation front calipers in red also, I'm have to check

IWANNAROCAGAIN

I'll check to see what I have, should have most of them, is yours speed density or maf?

Lasroc90

Speed density

Lasroc90

And a tpi 350 throttle body? Also need throttle cable and throttle valve cable

pendragon618

Payment sent for the Alpine via paypal on 10-24. I have sent you a couple of pms to which you have not responded.....

IWANNAROCAGAIN

Pm'd with tracking info

IWANNAROCAGAIN

IWANNAROCAGAIN

Bump

IWANNAROCAGAIN

Bump

Necron

iTrader: (1)

Did you check another Front LS1 Caliper Set?

anesthes

iTrader: (12)

Whats the deal with the heads? Guides junk?

What happened to the valves?

-- Joe

IWANNAROCAGAIN

Dissasembled heads to be cleaned up, may still have valves in a box somewhere, planned on putting all new valves and springs but project fell through.

IWANNAROCAGAIN

I'll have to check my storage in long beach, could swear I have a set of red ls1's somewhere

anesthes

iTrader: (12)

Well, I'd be interested in the heads if you had all the original valves + retainers. I have some new zz4 springs in the shop.

I just don't want to spend money on valves, keepers, retainers, etc cuz zz4 heads just are not worth what they used to be.

-- Joe

IWANNAROCAGAIN

I'll take a look tomorrow to see if I can find the valves, I have the retainers and locks in a box along with a set of springs

IWANNAROCAGAIN

Bump

anesthes

iTrader: (12)

Did you find 'em ?

-- Joe

Blizzard Bill

Are the heads a dead issue or are they available?

wesilva

iTrader: (35)

Are the roller rockers still available? Brand?