caster camber plate "spacers"
#2
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,650
Likes: 0
Received 44 Likes
on
42 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: caster camber plate "spacers"
No one does
#4
Supreme Member
iTrader: (33)
Join Date: Jul 2000
Location: Boosted Land
Posts: 5,945
Likes: 0
Received 1 Like
on
1 Post
Car: 92 Z28
Engine: Boosted LSX
Re: caster camber plate "spacers"
I dont think mine is 1inch. but are you talking like this?
http://www.cecoatings.com/images/Car...-51-19_497.jpg
http://www.cecoatings.com/images/Car...-09-39_543.jpg
http://www.cecoatings.com/images/Car...-51-19_497.jpg
http://www.cecoatings.com/images/Car...-09-39_543.jpg
#6
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,694
Received 747 Likes
on
506 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: caster camber plate "spacers"
A lot of guys used to make them but they were prototype stuff.
#7
Member
iTrader: (1)
Join Date: May 2004
Location: new york
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 pontiac trans am
Engine: Procharged 5.7l
Transmission: t-56
Axle/Gears: stock 9 bolt 3.71
Re: caster camber plate "spacers"
Materials and the machine time cost is the biggest problem. I'm currently working on a set made out of Delron. Since there is only compression load it should be just fine, not to mention much lighter than a 1" thick piece of aluminum.
I'm currently waiting to hear back from my design group on the cost to produce these.
I'm currently waiting to hear back from my design group on the cost to produce these.
Trending Topics
#8
Junior Member
iTrader: (3)
Join Date: Jan 2012
Location: Palm Desert, CA.
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 RS Camaro
Engine: LS6
Transmission: Tremec 6 Speed
Axle/Gears: FAB 9, Floater, 370 True Trac
Re: caster camber plate "spacers"
I am interested on spacers!!!!
As in Yesterday.
Dennis
As in Yesterday.
Dennis
#10
Supreme Member
iTrader: (15)
Re: caster camber plate "spacers"
I have some 11/16" T6 aluminum spacers that I had made for a coil over setup. I had 2 sets made. the look like the above version but at 11/16" tall. They allow almost 3/4" spacing. I currently put on a set of 1/2" spacers for mine. and this is what they look like.
I can sell a set of the 11/16" ones if someone wanted them. they are threaded for 5/16-18 bolts.
I can sell a set of the 11/16" ones if someone wanted them. they are threaded for 5/16-18 bolts.
#11
Supreme Member
Join Date: Jul 2007
Location: Howard Lake, MN
Posts: 1,293
Likes: 0
Received 4 Likes
on
4 Posts
Car: 86 Camaro
Engine: 355- hopefully a 5.3 this summer
Transmission: 700r4
Axle/Gears: 3.42
Re: caster camber plate "spacers"
Materials and the machine time cost is the biggest problem. I'm currently working on a set made out of Delron. Since there is only compression load it should be just fine, not to mention much lighter than a 1" thick piece of aluminum.
I'm currently waiting to hear back from my design group on the cost to produce these.
I'm currently waiting to hear back from my design group on the cost to produce these.
#12
Junior Member
iTrader: (3)
Join Date: Jan 2012
Location: Palm Desert, CA.
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 RS Camaro
Engine: LS6
Transmission: Tremec 6 Speed
Axle/Gears: FAB 9, Floater, 370 True Trac
Re: caster camber plate "spacers"
the struts are trying to push sideways towards the engine as the car sits, and they get pushed in every direction as the car drives down the road and hits bumps and takes corners and what not... i wouldn't be trusting any form of plastic to hold under those kinds of loads..
#13
Supreme Member
iTrader: (6)
Join Date: Aug 2011
Location: San Diego, California For Now
Posts: 2,379
Likes: 0
Received 10 Likes
on
10 Posts
Car: 88 Formula, 90 Iroc RIP, 92 RS Sold
Engine: 305 to 350
Transmission: 700r4
Axle/Gears: 10 Bolt
Re: caster camber plate "spacers"
You guys see any benefit ride quality with spacer and aftermarket camber plates
Thread
Thread Starter
Forum
Replies
Last Post
morrow
Suspension and Chassis
78
01-13-2024 12:29 PM
monte87cortez
Transmissions and Drivetrain
2
09-26-2015 08:10 PM