power steering return hose size?
#1
Member
Thread Starter
power steering return hose size?
I'm out of state at the moment and do not have access to my car. But does anyone know off hand what size the oil return line is coming off of the power steering box? I would like to install an inline filter onto the line, but don't know which size to get. They make the filters in 3/8", 1/2", and 5/8".
#2
Supreme Member
Join Date: Jul 2007
Location: Howard Lake, MN
Posts: 1,293
Likes: 0
Received 4 Likes
on
4 Posts
Car: 86 Camaro
Engine: 355- hopefully a 5.3 this summer
Transmission: 700r4
Axle/Gears: 3.42
Re: power steering return hose size?
3/8". might as well buy a few feet of new hose while are at it if yours is still original- it's not that expensive.
#3
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,027
Received 1,662 Likes
on
1,261 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Re: power steering return hose size?
Get the right kind of hose if you do... fuel line won't cut it.
Trans fluid cooler hose will also work.
Trans fluid cooler hose will also work.
#4
Supreme Member
Join Date: Jul 2007
Location: Howard Lake, MN
Posts: 1,293
Likes: 0
Received 4 Likes
on
4 Posts
Car: 86 Camaro
Engine: 355- hopefully a 5.3 this summer
Transmission: 700r4
Axle/Gears: 3.42
Re: power steering return hose size?
just tell them you want power steering hose. it looks like someone wrapped tape around the outside of it and it's a lot stiffer than fuel hose.
#6
Member
Thread Starter
Re: power steering return hose size?
It is 3/8". Got it all sorted out. Had to make sure that the guy from the local parts store didn't give me fuel hose - its not compatible with power steering fluid. Sure is a mess replacing a pump and everything. I put in a Magnefine filter to keep my new steering stuff nice.
http://www.magnefinefilters.com/Magn...er-R038M-P.htm
http://www.magnefinefilters.com/Magn...er-R038M-P.htm
Trending Topics
#8
Supreme Member
iTrader: (56)
Re: power steering return hose size?
yes the 6an hose will work on the low pressurized side. its set up for all oils and most fuels...(I checked with 2 diff makers of the stuff..) use the Teflon lined for the pressurized side with the fitting for it.. reg AN fittings for the low/return side..
The colors are off just a bit with the 2 dif type of hose fitting Hi vs low pressur
Compression fitting to 6AN. for the low press return hard line fitting not shown. this way no hose clamps are used.
The colors are off just a bit with the 2 dif type of hose fitting Hi vs low pressur
Compression fitting to 6AN. for the low press return hard line fitting not shown. this way no hose clamps are used.
Last edited by articwhiteZ; 04-26-2016 at 07:40 PM.
Thread
Thread Starter
Forum
Replies
Last Post
colton_carlson
Firebirds for Sale
7
03-08-2019 12:21 PM
evilstuie
Engine/Drivetrain/Suspension Wanted
15
04-14-2016 08:52 PM
toronto formula
Engine/Drivetrain/Suspension Parts for Sale
15
11-10-2015 06:17 AM
knight72
Engine/Drivetrain/Suspension Wanted
0
08-10-2015 09:32 PM