Search



Go Back   Third Generation F-Body Message Boards > Tech Boards > Auto Detailing and Appearance
Register Forgot Password?

Auto Detailing and Appearance Share tips and tricks on how to make your Third Gen shine! Get opinions on products or how something tasteful looks on your Chevrolet Camaro or Pontiac Firebird.

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 06-02-2003, 10:51 PM   #1
Supreme Member
 
TransAm12sec's Avatar
 
Join Date: Aug 2002
Location: Milwaukee, Wisconsin
Posts: 2,074
Car: 1982 Trans Am
Engine: LG4
Transmission: 200C
Axle/Gears: 3:73

Classifieds Rating: (0)

Send a message via AIM to TransAm12sec
Painting bolts in engine compartment

I like to take what’s rusty in my engine compartment out to sand, prime, and paint it. Last time I did this to some bolts. I remember when tightening the bolts after the process some of the paint would come off and brown primer would show. What would be the easiest way to make it look good without the paint chipping off after using the wrench to tighten them?

Would detailing them after they have been tightened be the easiest way?
__________________
Online Drag Racing -------Reaction Time Tester!
Red 1982 Trans Am MSE Hooker 1 5/8 primaries, 3 inches back, 3:73s
Red 1990 Formula with ZZ4 motor, Hooker 2055s, American Thunder catback
Black 1991 GTA with 3 inch Flowmaster Catback system
Black 2002 WS6 Bone Stock

TransAm12sec is offline vBGarage Page   Reply With Quote
Old 06-03-2003, 12:19 AM   #2
TGO Supporter
 
Justins86bird's Avatar
 
Join Date: Jul 1999
Location: Another world, some other time
Posts: 3,806
Car: 86 & 92 Firebirds
Engine: The Mighty 305!
Transmission: 700R4

Classifieds Rating: (0)

You could wrap some masking tape around the bolt, tighten, then remove the tape.
__________________
-Justin- out of my mind and I'll never know why

'86 Pontiac Firebird 305-4bbl / 700R4 T-Top WS6
'92 Pontiac Firebird 305-TBI / 700R4 T-Top
'76 Chevrolet Silverado C10 350-4bbl / TH350 longbed

click for my Homepage at CarDomain to see my mods
da computer: AMD A64 3400+ @ 2.6GHz in green Aspire SuperAlien case.click for a pic!
Teddy!

There can be only one!!
Justins86bird is offline vBGarage Page   Reply With Quote
Old 06-03-2003, 01:13 AM   #3
Senior Member
 
Join Date: Sep 2002
Location: Norwalk, Iowa
Posts: 1,834

Classifieds Rating: (0)
Or if you can get to the bolt after it's been installed you could mask it off real quick and spray it real quick to touch it up.

Or find yourself a model paintbrush and spray some of the paint on a piece of paper or cardboard and touch it up with the paintbrush.
joshp14 is offline vBGarage Page   Reply With Quote
Old 06-05-2003, 12:03 AM   #4
Senior Member
 
Mirror Image's Avatar
 
Join Date: Mar 2003
Location: Birmingham Alabama
Posts: 675
Car: 1991 Firebird convertible
Engine: 377
Transmission: 700 R4
Axle/Gears: 342 Limited slip

Classifieds Rating: (1)

Quote:
Originally posted by Justins86bird
You could wrap some masking tape around the bolt, tighten, then remove the tape.
Im with you the tape keeps from chiping the paint off
Mirror Image is offline vBGarage Page   Reply With Quote
Old 06-05-2003, 07:11 AM   #5
Supreme Member
 
Join Date: Jul 1999
Location: Plano, TX
Posts: 1,817
Car: 1992 RS
Engine: 406 Stealth Ram
Transmission: 700R4

Classifieds Rating: (0)
Quote:
Originally posted by Mirror Image
Im with you the tape keeps from chiping the paint off
Not if you need to put any sort of torque on it. I say take them out and either clean them up with a wire wheel, or get replacement stainless steel 12 point bolts from ARP or something
Scott_92RS is offline vBGarage Page   Reply With Quote
Old 06-05-2003, 07:25 AM   #6
Senior Member
 
Join Date: May 2003
Location: Lisbon, NH
Posts: 484

Classifieds Rating: (0)
I would say to use a brush applied paint. Just hit it after you torque it down.
MCas7 is offline vBGarage Page   Reply With Quote
Old 06-05-2003, 07:25 AM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > Auto Detailing and Appearance

Tags
86, arp, auto, bolt, bolts, camaro, car, compartment, engine, paint, painting, repainting, tape, tighten, tightening, tips, tools
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 01:44 AM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
All content copyright © 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details