Choke thermostat.
#1
Member
Thread Starter
Join Date: Apr 2005
Location: tasmania australia
Posts: 328
Received 0 Likes
on
0 Posts
Car: 1985 z28 camaro
Engine: 305 lg4,edelbrock,3"air cleaner.k&n
Transmission: turbo 700r4 w/b&m megashifter
Axle/Gears: Stock.
Choke thermostat.
Hi All,If i have the choke thermostat out,ie, the type with the metal coil,if i apply
power to the connector where the choke power wire goes to normally,should it heat up or should the coil move at all,as i tried this and nothing happened.I checked at the coil itself with a multimeter and got 12 volts so i dont know if its working or not.I'm just trying to work out my current problem and eliminate things as i go.Thanks for any help.
Alicat.
power to the connector where the choke power wire goes to normally,should it heat up or should the coil move at all,as i tried this and nothing happened.I checked at the coil itself with a multimeter and got 12 volts so i dont know if its working or not.I'm just trying to work out my current problem and eliminate things as i go.Thanks for any help.
Alicat.
#2
Supreme Member
Join Date: Aug 2005
Location: Yellowknife, NWT, Canada
Posts: 3,004
Likes: 0
Received 2 Likes
on
2 Posts
Car: 84 Z28
Engine: 357
Transmission: TH-350C
Axle/Gears: 3.43
Re: Choke thermostat.
The coil is bimetallic. When it has power applied to it, the 2 metals heat up at different rates and it causes the thing to spin slightly in turn opening/closing the choke plate.
If you have a full 12v on the wire going to the choke, chances are the choke has bit the dust. Especially if it doesnt feel warm(or hot) to the touch after a drive.
If you have a full 12v on the wire going to the choke, chances are the choke has bit the dust. Especially if it doesnt feel warm(or hot) to the touch after a drive.
#3
Moderator
iTrader: (14)
Join Date: Mar 2000
Location: Littleton, CO USA
Posts: 43,169
Likes: 0
Received 35 Likes
on
34 Posts
Car: 82 Berlinetta/57 Bel Air
Engine: LS1/LQ4
Transmission: 4L60E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
If you take the thermostat off of the carb, and apply 12 volts to the terminal, you have an open circuit.
It needs a complete circuit, so you have to ground the coil as well.
If you did that and it didn't move, then you've got a defective thermostat.
Assuming this is a stock carb, that is, which only has one wire and is grounded through the carb. Aftermarket carbs/choke thermostats often are 2-wire.
It needs a complete circuit, so you have to ground the coil as well.
If you did that and it didn't move, then you've got a defective thermostat.
Assuming this is a stock carb, that is, which only has one wire and is grounded through the carb. Aftermarket carbs/choke thermostats often are 2-wire.
#4
Junior Member
Join Date: Feb 2004
Location: Sunny LaCrosse FL
Posts: 91
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 Firebird
Engine: LG4 feedback controlled 350
Transmission: used to be T5 now T56
Re: Choke thermostat.
Does the choke thermostate get a signal from the engine temperature sensor, or will the bimetal coil heat and open the choke regardless of engine temp?
How do the engine / computer communicate with the carb choke?
What happens if one heats up before the other? Like defective choke coil, or too cool a thermostat or defective engine temp sensor and both the carb and engine are not in sync with regards to temperature.
These questions are in reference to the feedback carb system.
Thanks!
How do the engine / computer communicate with the carb choke?
What happens if one heats up before the other? Like defective choke coil, or too cool a thermostat or defective engine temp sensor and both the carb and engine are not in sync with regards to temperature.
These questions are in reference to the feedback carb system.
Thanks!
#5
Moderator
iTrader: (14)
Join Date: Mar 2000
Location: Littleton, CO USA
Posts: 43,169
Likes: 0
Received 35 Likes
on
34 Posts
Car: 82 Berlinetta/57 Bel Air
Engine: LS1/LQ4
Transmission: 4L60E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
The computer has nothing to do with it. It's in the alternator - when there's enough voltage from the alternator, it kicks a relay that powers the choke thermostat.
#6
Member
Thread Starter
Join Date: Apr 2005
Location: tasmania australia
Posts: 328
Received 0 Likes
on
0 Posts
Car: 1985 z28 camaro
Engine: 305 lg4,edelbrock,3"air cleaner.k&n
Transmission: turbo 700r4 w/b&m megashifter
Axle/Gears: Stock.
Re: Choke thermostat.
Hi,I forgot to ground it,so i did that and the coil moved around about 1/4 inch and got warm as well so it works ok i assume.Now i'll have to keep checking things out until i find out what's wrong with the thing.It's defininitely something to do with the carby as far as i can see,i just have to work out what.
Alicat
Alicat
#7
Supreme Member
Re: Choke thermostat.
Aside from the "does it heat up?" test you also want to test it's resistance. You must do this when it's cold (room temperature)- not heated up. You should see 5-10 Ohms resistance on a good one. 20 Ohms max. If it's beyond 20-25 ohms it's getting "weak" and won't work reliably.
Trending Topics
#8
Member
Thread Starter
Join Date: Apr 2005
Location: tasmania australia
Posts: 328
Received 0 Likes
on
0 Posts
Car: 1985 z28 camaro
Engine: 305 lg4,edelbrock,3"air cleaner.k&n
Transmission: turbo 700r4 w/b&m megashifter
Axle/Gears: Stock.
Re: Choke thermostat.
Okay,i tested the resistance and got between 13 and 14 ohms so it's probably
not bad for a original one.
Alicat.
not bad for a original one.
Alicat.
Thread
Thread Starter
Forum
Replies
Last Post
MikkoV
TPI
2
09-09-2015 04:25 PM
56, alternator, carburetor, choke, cools, do, e2se, ohm, ohms, resistance, rochester, test, thermostat, thermostate, thermostats