TBI to carb conversion?
#1
Member
Thread Starter
Join Date: Dec 2006
Location: Oklahoma
Posts: 183
Likes: 0
Received 0 Likes
on
0 Posts
Car: Too many to list...
TBI to carb conversion?
I would like to know about converting from TBI to carb. Other than intake, carb, and dizzy, what hard parts would be required and what is the general procedure for this swap?
Truck: 1990 Chevy. 350 TBI - 700-R4
The truck has a slew of bolt ons, + cam (crane2030) and ported heads, Bored .060 .
Please share with me anything you would be kind enough to share
Truck: 1990 Chevy. 350 TBI - 700-R4
The truck has a slew of bolt ons, + cam (crane2030) and ported heads, Bored .060 .
Please share with me anything you would be kind enough to share
#2
Member
iTrader: (1)
Join Date: Nov 2007
Location: Sacramento CA
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1982 Z28
Engine: 385ci w/carb
Transmission: TH350 w/3200ish Stall
Axle/Gears: 10 bolt :( 3.23 gears w/ posi
Re: TBI to carb conversion?
You will also need a return style fuel pressure regulator or a fuel pump designed for a carb.
#3
Junior Member
Join Date: Jun 2002
Location: Syracuse, NY
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2005 Audi A4 Avant
Engine: 1.8T
Re: TBI to carb conversion?
There is an excellent technical article on how to perform this conversion. It's one of the top articles on the list, definitely check it out. I'm also in the process of converting from TBI to carb.
#4
Junior Member
Join Date: Nov 2008
Location: Mobile, AL
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro IROC-Z
Engine: 305ci 5.0L (TBI to carb)
Transmission: manual
Re: TBI to carb conversion?
got the fuel injectors off... after i took this pic i cleaned off that manifold as best i could, as you can see its pretty nasty, stuff all over it. anyways, after that i removed the manifold, and when i took my foot off the front end, the car shifted, and part of an acorn fell from somewhere, directly into the #3 port. i couldn't believe it, a hole in one. anyways, i rigged up a piece of 3/4" plastic tube to the end of a vacuum cleaner and was able to get it out of there, and then i vacuumed the other ports just to make sure nothing fell in there... they were clean. as soon as i get the new manifold i will post some more pics.
#5
Junior Member
Join Date: Nov 2008
Location: Mobile, AL
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro IROC-Z
Engine: 305ci 5.0L (TBI to carb)
Transmission: manual
Re: TBI to carb conversion?
also... i'm not totally familiar with all of the un-necessary items (when switching to carbed), any chance anyone could point out in this picture what i don't need and can remove? thank you very much, everyone here has been extremely helpful so far.
#6
Re: TBI to carb conversion?
Trending Topics
#8
Moderator
iTrader: (14)
Join Date: Mar 2000
Location: Littleton, CO USA
Posts: 43,169
Likes: 0
Received 35 Likes
on
34 Posts
Car: 82 Berlinetta/57 Bel Air
Engine: LS1/LQ4
Transmission: 4L60E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
It's linked in the "welcome to the carburetor forum" sticky in the top section of this forum.
It can also be found by going to the thirdgen.org homepage and clicking on the tech articles link on the left side of the page.
It can also be found by going to the thirdgen.org homepage and clicking on the tech articles link on the left side of the page.
#9
Junior Member
Join Date: Jun 2012
Location: florida
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 k15000
Engine: 305
Transmission: th400 (m80) 4x4
Axle/Gears: original
Re: TBI to carb conversion?
the biggest issue I notice is the 700r tranny how to control it
look at my conversion and if any questions reply
look at my conversion and if any questions reply
#10
Supreme Member
Thread
Thread Starter
Forum
Replies
Last Post
GeneralIesrussi
Tech / General Engine
0
09-03-2015 03:23 AM