 | 
11-20-2004, 04:03 PM
|
#1 | | Member
Join Date: Jul 2003 Location: Colorado Springs, CO
Posts: 166
| 16197427 pinout
Anybody have a harness connector pinout diagram for a 16197427 PCM?
Bill | | | |  
|  | |
11-21-2004, 09:59 AM
|
#2 | | Senior Member
Join Date: Jul 2003 Location: Dallas
Posts: 457
| Re: 16197427 pinout
Quote: Originally posted by MrBill
Anybody have a harness connector pinout diagram for a 16197427 PCM?
Bill | Here you go. ftp://ftp.diy-efi.org/pub/gmecm/manuals/16197427/ . HTH
__________________
If it doesn't make it go fast, stop fast, or look cool, its fluff! | |
| | |
11-21-2004, 10:04 AM
|
#3 | | Member
Join Date: Jul 2003 Location: Colorado Springs, CO
Posts: 166
| Sweet. Thanks! | |
| | |
11-21-2004, 11:17 AM
|
#4 | | Senior Member
Join Date: Jul 2003 Location: Dallas
Posts: 457
| Are you cooking somethng up for this PCM? If so, count me in. I have a lot of info on this PCM and have been messing with it for a while.
__________________
If it doesn't make it go fast, stop fast, or look cool, its fluff! | |
| | |
11-21-2004, 11:38 AM
|
#5 | | Member
Join Date: Jul 2003 Location: Colorado Springs, CO
Posts: 166
| No, not really. I'm building a Prominator for a 512K PCM and just need to set up this 7427 I have to test it with.
Sorry to disappoint. LOL | |
| | |
11-22-2004, 10:27 PM
|
#6 | | Junior Member
Join Date: Mar 2004 Location: Atlanta, GA
Posts: 40
| Hey HaulinA$$,
I've been searching for a component/board level schematic like the ones on ludis' page for the 16197427. Any Ideas on where to find one??
Sorry, didn't mean to hijack the link but ...... the ? is semi-related.
Thanks
89350STRO | |
| | |
11-22-2004, 10:53 PM
|
#7 | | Senior Member
Join Date: Jul 2003 Location: Dallas
Posts: 457
| Hey 89350STRO, I have not found any specific schematics for the '7427. It has some similarities to the 1227747 such as the injector driver circuits but that is as far as I got before giving up. From what I can tell, it is a hybrid of the P4 ECM (faster cpu and aldl, no onboard ROM, etc.) and the older C3 ECM (peak/hold injector drivers) with added transmission control. Sorry, that is the best I can do. If you ever come across schematics, let me know. HTH
__________________
If it doesn't make it go fast, stop fast, or look cool, its fluff! | |
| | |
12-07-2004, 02:49 PM
|
#8 | | Member
Join Date: Jul 2003 Location: Colorado Springs, CO
Posts: 166
| What about pinouts for a 16196395? Same as the 6396? | |
| | |
12-07-2004, 03:34 PM
|
#9 | | TGO Supporter
Join Date: Aug 2001 Location: NJ/PA
Posts: 1,007
Car: Yes Engine: Many Transmission: Quite a few | try this website, lots of interesting stuff. look under wiring, and there should be numerous late model ecm stuff for trucks. http://www.megspace.com/cars/16147060/index_tk.html
good luck! | |
| | |
12-07-2004, 05:10 PM
|
#10 | | Member
Join Date: Jul 2003 Location: Colorado Springs, CO
Posts: 166
| Need a pinout for a 16191947 now. Anybody? | |
| | |
12-07-2004, 07:11 PM
|
#11 | | Senior Member
Join Date: Jul 2003 Location: Dallas
Posts: 457
| Quote: Originally posted by MrBill
What about pinouts for a 16196395? Same as the 6396? | They are the same as the 16197427. It is the same PCM. HTH
__________________
If it doesn't make it go fast, stop fast, or look cool, its fluff! | |
| | |
06-12-2006, 03:45 AM
|
#12 | | Junior Member
Join Date: Apr 2006
Posts: 11
| So i found this thread but im confused.
For the Jbody project i'm converting a ln2 pcm that runs in a s10 with the ln2 engine to run in a 95 cavalier with a manual trans and the ln2.
My question is, where can i find the pinout to the 16196285 and 16196395 pcms.
I have a sacrificial pcm to get female connectors and i have male connectors, and so what i need to know is where the pins plug. Im doing some google searching, so i will let you all know if i find what im looking for.
I still am benching the 16196285 pcm, but im finding the the 36 mask is uncommented and hard to figure out. | |
| | |
01-04-2010, 05:20 PM
|
#13 | | Junior Member
Join Date: Aug 2009 Location: New York
Posts: 60
Car: 1990 Jeep YJ Engine: 70's 350 w/87 Z TPI-MAP Conversion Transmission: Muncie SM 465 Granny Low 1st Axle/Gears: 4:10 Gears in both axles | Re: 16197427 pinout
Quote:
Originally Posted by kyanox  So i found this thread but im confused.
For the Jbody project i'm converting a ln2 pcm that runs in a s10 with the ln2 engine to run in a 95 cavalier with a manual trans and the ln2.
My question is, where can i find the pinout to the 16196285 and 16196395 pcms.
I have a sacrificial pcm to get female connectors and i have male connectors, and so what i need to know is where the pins plug. Im doing some google searching, so i will let you all know if i find what im looking for.
I still am benching the 16196285 pcm, but im finding the the 36 mask is uncommented and hard to figure out. | 3 years later, any luck with that 16196395 schematic? 1/04/2010  | |
| | |
01-11-2010, 05:10 AM
|
#14 | | Junior Member
Join Date: Aug 2009 Location: New York
Posts: 60
Car: 1990 Jeep YJ Engine: 70's 350 w/87 Z TPI-MAP Conversion Transmission: Muncie SM 465 Granny Low 1st Axle/Gears: 4:10 Gears in both axles | Re: 16197427 pinout
Quote:
Originally Posted by Glenno 3 years later, any luck with that 16196395 schematic? 1/04/2010 |
bump  | |
| | |
06-07-2011, 10:11 PM
|
#15 | | Supreme Member
Join Date: Oct 2002 Location: Idaho
Posts: 1,029
| Re: 16197427 pinout
Quote:
Originally Posted by Glenno bump | Same as the 16197427 is the 16197395. Wiring diagrams are here: http://www.gearhead-efi.com/Fuel-Inj...CM-Information
Last edited by EagleMark; 11-25-2011 at 12:56 AM.
| |
| | |
06-07-2011, 10:11 PM
| | ThirdGen 1992 Camaro
Paid Advertisement | |
|
| Tags | 16147060, 16196395, 16197427, 2000, 7427, aldl, diagram, ecm, gm, pcm, pinout, s10, schematic, transmission, wire  | | Thread Tools | Search this Thread | | | |
Posting Rules
| You may not post new threads You may not post replies You may not post attachments You may not edit your posts
HTML code is Off | | |
| | | |
