Go Back   Third Generation F-Body Message Boards > Tech Boards > DFI and ECM
Sign in using an external account
Register Forgot Password?

DFI and ECM Discuss all aspects of DFI (Digital Fuel Injection), ECMs (Electronic Control Module), scanners, and diagnostic equipment. Fine tune your Third Gen computer system for top performance.

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 05-27-2009, 03:30 AM   #1
Junior Member
 
Join Date: Apr 2009
Posts: 5

Classifieds Rating: (0)
ECM problem?

ok so ive been doing some reading around.I thought perhaps the 2.93 gears were the culprit but reading these forums that may not be the case. This car has no punch whatsoever. I literaly have to put my foot all the way to the floor when coming off a stop light to get it moving and if Im on a step hill have to keep it to the floor just to maintain 60 MPH. I have jad a tuneup done, changing all spark plugs and wires. I have had a new catalytic converter put on and intake manifold gaskets replaced ruling out any exhaust problems.

I had the tranny replaced its a 4l60E and the mechanic says its a possible ECM related issue. Does this mean that I need to replace it? I just find it really hard to believe that that little box can be causing so much. It shifts fine and im really at a loss and am really tired of throwing money away on this thing.

btw this is a 92 chevy caprice
tyriekfv is offline vBGarage Page   Reply With Quote
Old 05-27-2009, 12:37 PM   #2
Supreme Member
 
JP86SS's Avatar
 
Join Date: Apr 2004
Location: Browns Town
Posts: 2,933
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller
Transmission: 700R4 HomeBrew, 3.8K stall 3 diskLU
Axle/Gears: 3:73 Posi, 7.5 Soon to break

Classifieds Rating: (0)
Re: ECM problem?

Confirm your timing is set correctly with the "Bypass" unplugged.
Sounds like its way off and is probably overheating (or getting hotter than it should)
JP86SS is offline vBGarage Page   Reply With Quote
Old 05-27-2009, 01:34 PM   #3
Junior Member
 
Join Date: Apr 2009
Posts: 5

Classifieds Rating: (0)
Re: ECM problem?

I thought it was a timing issue as well which is why I had the tuneup and got that adjusted. But that didnt help. Outside of what I posted the car runs fine, doesnt seem to burn gas unnecessarily and only idles high when its cold. Some other symptoms I forgot to mention. The speedometer stopped working, then probably a week later the odometer stopped working. When I start the car I can see the needle on the speedometer jump like it just got power, but the thing does not move at all when driving. Not sure if the two are related but that is something else going on.
tyriekfv is offline vBGarage Page   Reply With Quote
Old 05-28-2009, 12:14 AM   #4
Supreme Member
 
JP86SS's Avatar
 
Join Date: Apr 2004
Location: Browns Town
Posts: 2,933
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller
Transmission: 700R4 HomeBrew, 3.8K stall 3 diskLU
Axle/Gears: 3:73 Posi, 7.5 Soon to break

Classifieds Rating: (0)
Re: ECM problem?

Check fuel pressure (or change the fuel filter) if you have any back fires when accellerating hard.
Do you have any way to datalog the car?
That would shed some light on how its running.
JP86SS is offline vBGarage Page   Reply With Quote
Old 05-28-2009, 12:52 AM   #5
Junior Member
 
Join Date: Apr 2009
Posts: 5

Classifieds Rating: (0)
Re: ECM problem?

I dont Jp. I dont have any backfires but sometimes it stumbles. Very random it seems when it does it. Havent done it for about 2 weeks but then did this morning. What I mean by that is. From a stop and seems to want to cut out, but never does. I take my foot off the pedal and back on to get it out of the stumble. Its the same feeling as if you had just ran out of gas. I do have a fuel filter in my garage that I have sitting for it because I thought that might have been the case for the stumbling, but since it hadnt been doing it, it sits. I'll put that on tomorrow and report back here.

On the dataloging thing again. Can I take the car to like autozone and have them do it or rent one?
tyriekfv is offline vBGarage Page   Reply With Quote
Old 05-28-2009, 12:52 AM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > DFI and ECM
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 01:52 PM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.5.2
All content copyright © 1997 - 2012 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details