??Connector terminal for 1227727 ECM connector?? - Third Generation F-Body Message Boards

kevosiroc · 06-06-2006, 05:39 PM

Where can I get a connector terminal for 1227727 ECM.

I want to put my wideband O2 sensor into the MAP(2) input for the 8D_WB hac. I need to know where to find the terminal (and its' p/n)

Can anyone help??

This ad is not displayed to registered members.
Register your free account today and become a member on ThirdGen!

-=Jeff=- · 06-06-2006, 08:22 PM

C21

According tot he pinout conversion that was on Ludis' website

JP86SS · 06-06-2006, 10:37 PM

Some old info I found on the DIY-EFI site a while back.

Code:

Some GM part numbers:
If you're building/repairing a harness for the 1227165/727/730/749/808/747 ecms,
 you'll need 12047946 and 12045575.
 For 3 connector ECMs you'll also want 12089591.
 These are "car side" ECM connectors.
 Crimp terminals for the above are 12089660. 
The connector inside a 747/808/148 ECM is Packard #12020756.
The yellow connector on a 730/749 is 12048046

kevosiroc · 06-07-2006, 04:48 PM

Quote:

Some old info I found on the DIY-EFI site a while back.
Code:

Some GM part numbers: If you're building/repairing a harness for the 1227165/727/730/749/808/747 ecms, you'll need 12047946 and 12045575. For 3 connector ECMs you'll also want 12089591. These are "car side" ECM connectors. Crimp terminals for the above are 12089660. The connector inside a 747/808/148 ECM is Packard #12020756. The yellow connector on a 730/749 is 12048046

I did not think the terminals would be the same for the 7730 and the 7727 b/c the 7727 is an underhood ECM exposed to the harsh engine compartment environment. So doing extensive research (hours of searching around on www.delphisecure2.com), I was able to locate the p/n's I was looking for.... and then some. So here is what I found out:

12066132 - terminals
12052924 - seals for the terminals (package of 20 p/n 12048086 seals)
12065877 - Connector 'C' (Green on my Vette)
12065878 - Connector 'D' (brown on my Vette)
12065876 - Connector 'B' (Red on my Vette)
12065875 - Connector 'A' (yellow on my Vette - manual says Yellow or Gray)
12059155 - Header for connectors 'A' and 'B' (header is what is attached to the ECM and what the connector mates to)
12059154 - Header for connectors 'C' and 'D'

I think the connectors and headers are discontinued.

kevosiroc · 06-07-2006, 04:59 PM

Quote:

Some old info I found on the DIY-EFI site a while back.
Code:

Some GM part numbers: If you're building/repairing a harness for the 1227165/727/730/749/808/747 ecms, you'll need 12047946 and 12045575. For 3 connector ECMs you'll also want 12089591. These are "car side" ECM connectors. Crimp terminals for the above are 12089660. The connector inside a 747/808/148 ECM is Packard #12020756. The yellow connector on a 730/749 is 12048046

Not only did I look up the p/n's for the terminals...... I compared the p/n the connector drawing called out witht p/n 12089660 (that the DIY-EFI site references)

I found the terminals are not the same length for starters, and the dimensions and shapes are just a bit different. I do not know if the are interchangeable, so since p/n 12066132 is available, I will try that one.

Maybe this info should be catalogged somewhere????

Attached are the drawings

JP86SS · 06-07-2006, 06:10 PM

[quote=kevosiroc]Maybe this info should be catalogged somewhere????/quote]

I saved it for future reference, nice work

RBob · 06-07-2006, 07:54 PM

I stickied this thread. At a later point I'll merge it into the DIY_PROM Guide book.

Thanks for the info,

BobR.

kevosiroc · 06-08-2006, 09:24 AM

Quote:

Originally Posted by RBob

I stickied this thread. At a later point I'll merge it into the DIY_PROM Guide book.

Thanks for the info,

BobR.

Glad I could help!

kevosiroc · 06-08-2006, 01:36 PM

To add another piece of info.....

I was looking for this info so I could utilize the 8D wideband hac.

These are the pinouts needed for the 1227727 ECM:

C21 = MAP(2)
C18 = TPS(2)

I have all the documents to back this up, but they are too large to attach

91GTABird · 06-08-2006, 09:36 PM

Sorry: Repost

justa4 · 06-13-2006, 04:46 PM

I have the terminals available... still on the reels for use on assembly lines.

Drop me a note off list and I can send you some.

dariojuan67 · 02-16-2008, 09:31 PM

Hello friend,i have a 1984 corvette crossfire and need to identify the pinouts for the stock ecm #1226430 and reconect them to the ecm#1227747,so that i can use this newer ecm,i'll apreciate your help,i need to install this ecm in my crossfire,thanks alot,if there's anything that i could do for your just leet me know,thanks a lot.

vetteoz · 02-18-2008, 07:30 AM

Quote:

Originally Posted by dariojuan67

Hello friend,i have a 1984 corvette crossfire and need to identify the pinouts for the stock ecm #1226430 .

Might help

Vette
http://www.autozone.com/az/cds/en_us...rInfoPages.htm

747
http://www.chevythunder.com/1227747_ecm_198892.htm

oldred95 · 02-18-2008, 02:33 PM

www.eficonnection.com should have what you need. He is a member on here. S10Wildside is his name.

xtremesunfire · 05-19-2008, 11:05 AM

sorry for bringing this back up but I just need to know what part number this is off the ecu I have pics of that yellow connector and the ecu is 1227730 and it came out of a 92 beretta gt 3.1.

and inside it say E1 to 16
and the wire diagram I got from the dealership is saying that is post to be green can somebody clear that up also. thanks

topacho · 10-29-2008, 11:37 AM

any diagram conecction for connector M from ECM 96417551 XAHD DELPHI MR140 ?

the connection diagram it's neccesary for this problem: