No turn signals...running out of ideas.
#1
Supreme Member
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Guilford, Connecticut
Posts: 1,428
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1988 IROC-Z camaro
Engine: 355 TPI
Transmission: tko 500
Axle/Gears: Dana 44 3.31 posi pbr brakes
No turn signals...running out of ideas.
I just noticed the other day that i dont have any turn signals on the car out of the blue. The hazzards still work however like normal. I pulled the turn signal relay (flasher?) and replaced it with no success. I also checked the fuse and it was good. Whats my next move?
#3
Supreme Member
Join Date: Jan 2006
Location: Mooresville NC
Posts: 3,341
Likes: 0
Received 10 Likes
on
10 Posts
Car: LOWERED ♦ CRIMSON METALFLAKE
Engine: ► 400 KUBES ◄
Transmission: 765R4
Axle/Gears: EATON POSI 4.56
Turn & Learn
Turn the ignition key to the RUN position.
Using a test light (the type for testing for voltage, not a continuity tester) probe the purple wire going to the steering column connector.
It’s the larger of the connectors located on the right side of the steering column.
If there’s power there, turn the blinker to the left position, then probe the LIGHT blue wire at the same connector.
Is there power there?
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
After The Fourth Barrel Roll I Lost Control Of The Car
.
Using a test light (the type for testing for voltage, not a continuity tester) probe the purple wire going to the steering column connector.
It’s the larger of the connectors located on the right side of the steering column.
If there’s power there, turn the blinker to the left position, then probe the LIGHT blue wire at the same connector.
Is there power there?
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
Happy Racing!
◙◙◙◙◙◙◙◙◙◙◙◙◙◙◙
After The Fourth Barrel Roll I Lost Control Of The Car
.
#4
Supreme Member
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Guilford, Connecticut
Posts: 1,428
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1988 IROC-Z camaro
Engine: 355 TPI
Transmission: tko 500
Axle/Gears: Dana 44 3.31 posi pbr brakes
Re: Turn & Learn
I fixed it!! Turns out the Haynes manual is lacking a bit in where the actual flasher is located. I thought i replaced it but instead i replace a relay right next to the hazzard flasher. I found the turn light flasher stuffed up above the convenience center and under the tach. It wasnt even c-clipped in like everyone on this board was saying. At any rate its all set now! Thanks for the help though.
#5
Junior Member
Join Date: Jun 2012
Location: Porterville, CA and Escondido, CA
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Camaro Iroc
Engine: 305 V8
Re: Turn & Learn
can you take a picture of it and post it here? i have the same problem and i have NO clue what the flasher looks like.
#6
Supreme Member
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Guilford, Connecticut
Posts: 1,428
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1988 IROC-Z camaro
Engine: 355 TPI
Transmission: tko 500
Axle/Gears: Dana 44 3.31 posi pbr brakes
Re: Turn & Learn
Here is a picture i grabbed off the net of what it looks like.
Mine was right above the convenience center in the car. I had to drop it down and feel around up there until i found it. It wasnt mounted to anything so i just yanked it down, unplugged it and plugged the new one in and problem was solved.
Mine was right above the convenience center in the car. I had to drop it down and feel around up there until i found it. It wasnt mounted to anything so i just yanked it down, unplugged it and plugged the new one in and problem was solved.
#7
Senior Member
Join Date: Oct 2005
Location: England
Posts: 941
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1987 GTA
Engine: 350 TPI w/ extras !
Transmission: 700R4
Re: No turn signals...running out of ideas.
mine was just stuffed under the dash, i only discovered it when i had to move the convienience centre and it fell down !
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
83 Crossfire TA
Suspension and Chassis
0
09-08-2015 12:06 PM