jnsbill

Need a T5 for my 84 TA, located in NJ - pls contact me at jnsbill@msn.com

84pontiac

i have a 1984 pontiac trans am with the t5 might be willing to sell if the price is right. only 100k on the transmission

jnsbill

Whats a "right price"? and where are you located?

86camaro383

I have a t5 out of a 87 camaro. Bellhouseing, clutch, and flywheel, Shifts threw all the gears just fine, and reverse worked fine. 200 obo Im in Lower NY zip 12566.

jnsbill

To - 86camaro383 - am very interested in your trans, your not too far away - but - trying to be careful your only reference for sales is a bad one
Got any good references? E-mail me directly at jnsbill@msn.com - thanks

86camaro383

what do you mean I only have a bad referance? I been selling parts on here since im a member. As far as I remember, The only conflict I had on here is I shipped a bumper and it got there cracked, but we settled that and I ended up paying him half the repair cost, that was because UPS wouldnt cover it. Besides, If you go to my classifieds rating has 2 positive feedbacks in it. I would say come by the my friends house tomarrow to drive it, but were pulling it out at 7 in the morning and junking the car after that.

jnsbill

Hey the only info I found was http://www.thirdgen.org/techboard/cl...html?highlight (86camaro383 =BAD SELLER)=

I am still interested in the trans, I was just looking for references

jnsbill

When you pull it send me the ID Tag number - thanks

86camaro383

click on the classifieds rating on the left, right below my user name. You have to click on the (2)

jnsbill

New to the site never noticed the feedback rating - we're good

Send me the ID Tag number and we should have a deal - it's a V8 Trans correct

86camaro383

yes. Ill get that tag ID for you.

86camaro383

Im looking at this thing and I dont see any tags.... I see casting numbers on the case...The deal is gotta be without the bellhouseing, my friend sold that yeasterday (friday)

jnsbill

Look for a number that begins 1352-xxx the last 3 numbers ID the trans, just to confrim this is a V8 trans. What do you want for it w/o the bellhousing?

86camaro383

I looked up everything online, everyone is saying this is a 5 spd out of a 85 s-10. wierd cosidering is was bolted up to a tbi 305.....I dont know if you still want it or not.

jnsbill

Couldn't find the 1352-xxx numbers? How did ya figure it was an S-10 trans?If its out of a 305 Camaro it should fit the T/A. Happen to keep the driveshaft? Still interested, let me do some checking, get back to you by Tues.

86camaro383

no I couldnt find any numbers. I just looked at the casting numbers on the case. There was some numbers underneith the borg warner name. I do have the old driveshaft as well. If you want i can give you that with the trans. I just want to be honest.

86camaro383

only numbers I found are 13520669, that was on the 'tailshaft" so to speak case of the trans.

jnsbill

Are you sure its 13520669, the closest number that matches to is 1352-069 Nissan 1984 300 ZX NA/EUR thats bizarre - do you know the history of the car? But if it was in a Camaro 305 it should be OK
just confirm that it's a 26 spline input shaft
How long is the trans and the driveshaft so I know it will fit in my trunk

86camaro383

there was a little space between the casting number and there was a '20'. I dont know if will make a difference. The trans should fit in your trunk, driveshaft, im not sure, I have to go back over there and measure it up. Im going to meet up with my buddy on thursday night ( all my parts are at my friends house because I cant keep them in my apartment. I know the kid bought the car off his uncle because the motor had a knock, he re-built the motor with his dad and then crashed it into a tree about 3 months ago. My buddy bought it and where parting it out. Thats all I know about the history of the car.

jnsbill

OK I'm still in - just confirm 26 spline and drivshaft length - final price?

86camaro383

Well i wanted 200 with everything, Hows 175 w.o the bellhousing?

jnsbill

$175 is OK - just confirm 26 spline and measure driveshaft - and we'll work out p/u

86camaro383

yup its a 26 spline.

jnsbill

Did you get a chance to measure the driveshaft, when is good to meet?

86camaro383

I completly forgot to measure the D/S. I will wed. when I hop over there again. As far as meeting up, you want to meet up this weekend?

jnsbill

86camaro383 - where'd ya go?

86camaro383

pm sent.

jnsbill

pm replied --- you were going to measure the d/s last Wed. and get back to me - I'll be in North Jersey Saturday night - contact me at jnsbill@msn.com and we'll work it out.

86camaro383

its like 41 inches, roughly.

jnsbill

Check your PM

86camaro383

didnt get one????

jnsbill

should be there?? check again and let me know

jnsbill

Bottom fell out of deal still looking - jnsbill@msn.com

88 IrocZ Vert