Vortec 350 Engine & Everything for Swap - Third Generation F-Body Message Boards

VortecTBI350GMC · 04-11-2008, 04:05 PM

Hey guys. I went through all the pains of collecting the stuff to make the best quality SBC install into my 94 TBI Sonoma 4x4. I have EVERYTHING to make the swap- the engine was in the truck and drivable but only got a total of about 10 miles on it! Never got to completely dial in the computer...Now I decided I want to go diesel so I need money! I am not putting prices on right now because I am just checking for interest. I don't have pics at the moment because I am in college 3 hrs away from my garage. Would be very easy to convert back to 96 & Newer Vortec Intake and distributor to run in a newer FSC truck- or slap a carb on the intake for non-computerized swaps! I also have the stock oil pan for camaros or other cars.
Will have pics by the end of May.

Here's some of the things I have:

1-1996 Vortec 350 4 bolt main Complete Engine (ran fine/ 110k miles/no ridge prior to freshening--Est 300 HORSEPOWER!!!)
~New rod/main/cam bearings/moly rings/Hone Job/HV Oil Pump/Shaft/frost
plugs/timing set/complete gasket set
~Nice gloss black paint job- not rusty and looks real sexy with the aluminum intake!

~S10 4x4 oil pan and sump (fabbed by a friend via JTR ext kit)
~JTR 4x4 Motor Mounts (block side- use 2.8 shells)
~Used stock grind LT1 roller cam w/ Z28 springs and roller tip rockers
~Aluminum 4BBL Summit brand Carb intake manifold
~Holley TBI adapter to intake
~50mm Ebay Bored TBI w/ stock 350 injectors/18 psi regulator spring/fuel press
gauge
~Exhaust Manifolds
-1 set from Camaro 305 TBI
-1 set from 1995 LT1 350 (have pics of these right now)
~Remote Oil Filter omitted (short filter mounts to block)

Price: $1200 Complete Motor/ $850 Long Block

1-TBI Chips.com Custom Burned Chip
~Made for engine above with 4L60E tranny and no EGR
~Works with 94-95 GM OBD1.5 Computers

Price: $125

1-1997 5spd 4x4 S10 8.5" 3.42 Factory POSI rearend- Great width for Camaros too!
~Has 120k miles but no real signs of wear
~Really hard to find rearend!

Price: $300

1-Magnaflow dual 2.25 In/3" out High Flow Catalytic Converter
~New IN Box!
~O2 Sensor Bung near dual inlet
~Paid $65 New on ebay

Price: $50

1-Complete Rebuilt 700R4 4x4 Tranny with receipts
~NEVER USED! Clean as a whistle and still has transgel around seals!
~Rebuilt 4.3 Stock Converter
~Kevlar band
~"The Beast" sunshell
~.500 Oversized Boost Valve
~Corvette Servo
~Wired for direct lockup in 4th (OD)- Just 2 wires to make it work!

Price: $750

Anything I missed? I probably have it! Email: beefiest101@yahoo.com or PM me
-Lance

F_N_JUNK · 04-12-2008, 01:16 PM

Location???
Price for parts???

VortecTBI350GMC · 04-12-2008, 02:32 PM

Sorry, didn't realize I hadn't put my location in my profile...
I'm from Appleton, WI.
As for price, I added figures to the listing.

DMX69785 · 05-20-2008, 04:25 AM

willing to part out just the block?

VortecTBI350GMC · 05-20-2008, 12:45 PM

Sorry I forgot I posted this here...Engine has been sold complete. Still have other S10 V8 parts.