You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!
89 2 bolt 350 bored .040 over (357) 1 pc rear main block
New Scat crank
New KB hyper pistons
5.7 reconditioned rods New ARP bolts
New rings & bearings
New cam bearings & freeze plugs
New Howard hyd roller cam 280/292 dur 504/504 lift 112 centerline
New hyd roller link lifters
New Comp Cam double roller timing chain
New Alum timing cover
New balancer
New HV oil pump & pickup w/steel shaft
New Moroso oil pan w/1 pc oil pan gasket
New flexplate w/bolts
Balanced rotating assy prof built ready for your topend over $2,800 invested
very interested in motor.. what cr are pistons setup for? Are you sure it was an 89 block?? havent seen many that werent allready setup for roller cam.
very interested in motor.. what cr are pistons setup for? Are you sure it was an 89 block?? havent seen many that werent allready setup for roller cam.
any v8 camaro/firebird block past 87 is a roller cam block, which uses a roller cam, IIRC
mmm I need more like 9.5.... 87 octane friendly... 10.1 is premium fuel territory if memory serves.. especialy with a cam like LT1 with 117 degrees lobe angle
mmm I need more like 9.5.... 87 octane friendly... 10.1 is premium fuel territory if memory serves.. especialy with a cam like LT1 with 117 degrees lobe angle
i have an 89 355 with cam around .525 lift hyper pistons crane rockers high flow oil pump new oil pan and gasket, also has a wieand intake. needs crank turned and bearings. + 400 cash
i have an 89 355 with cam around .525 lift hyper pistons crane rockers high flow oil pump new oil pan and gasket, also has a wieand intake. needs crank turned and bearings. + 400 cash
Sounds like a decent small block but i can't pay that much for one that needs a rebuild
holy buggering crap sticks batman! you are crazy! 1200 is a smokin deal, and if i werent going BBC then id snatch that up in a heart beat. problem is i got too many engines alreay :S im being tempted to snatch it up for my 78 gmc!
bump, Bump, BUMP for a good sale, this is a retarded deal for that nice of an engine, huge loss here
p.s.- is that beasty trans am yours? grr i wish i had that thing...and on the compression question. why not run 91 octane or more in your sports car, i do and my block is only 9.15/1, but i run premium cuz i loves my car plus if you do have to run it cus of 10/1 then all the better, mo-powah!!
Last edited by ModPog84z28; 03-22-2009 at 03:00 PM.
holy buggering crap sticks batman! you are crazy! 1200 is a smokin deal, and if i werent going BBC then id snatch that up in a heart beat. problem is i got too many engines alreay :S im being tempted to snatch it up for my 78 gmc!
bump, Bump, BUMP for a good sale, this is a retarded deal for that nice of an engine, huge loss here
p.s.- is that beasty trans am yours? grr i wish i had that thing...and on the compression question. why not run 91 octane or more in your sports car, i do and my block is only 9.15/1, but i run premium cuz i loves my car plus if you do have to run it cus of 10/1 then all the better, mo-powah!!
I know i've had a few offers $900 and $1,000 if i can't get my $1,200 i'll keep it
P.S. Yes the 2000 Formula in the pics is also mine and For Sale too