[TX] Lloyd Elliott AFR 1040's AGAIN
#1
Member
Thread Starter
iTrader: (21)
Join Date: Dec 2001
Location: Texas
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Lloyd Elliott AFR 1040's AGAIN
I had these "sold" but things did not work out so they are for sale again. Here's a rundown.
AFR 195cc heads part number 1040. They were run for about 2 hours previously by Anethes here from Thirdgen. I bought them from IrocZ30589 here who did not personally run these heads. They have been milled .035 by AFR to get the chambers down to 60cc. Springs are the AFR 8017's good to .600 lift. Valves are 2.05/1.60 that AFR uses. I took them to Lloyd Elliott who is one if the best hand porters out there. I've used him for SBC, LT1, LS1 stuff and have been very happy with his work. Look him up he knows what he's doing. They received a full port job on the intake and exhaust runners. Chambers were left alone as they did not need additional porting since AFR CNC's them. I had Lloyd flow them afterwards and these things are ridiculous. Was going to run a 1205 gasket. Flow number are
149/122 @ .200
208/171 @ .300
263/204 @ .400
298/226 @ .500
310/235 @ .600
314/239 @ .700
There is over $2k in these heads. $1500 shipped FIRM. Shipping to the lower 48 only.
Zach
AFR 195cc heads part number 1040. They were run for about 2 hours previously by Anethes here from Thirdgen. I bought them from IrocZ30589 here who did not personally run these heads. They have been milled .035 by AFR to get the chambers down to 60cc. Springs are the AFR 8017's good to .600 lift. Valves are 2.05/1.60 that AFR uses. I took them to Lloyd Elliott who is one if the best hand porters out there. I've used him for SBC, LT1, LS1 stuff and have been very happy with his work. Look him up he knows what he's doing. They received a full port job on the intake and exhaust runners. Chambers were left alone as they did not need additional porting since AFR CNC's them. I had Lloyd flow them afterwards and these things are ridiculous. Was going to run a 1205 gasket. Flow number are
149/122 @ .200
208/171 @ .300
263/204 @ .400
298/226 @ .500
310/235 @ .600
314/239 @ .700
There is over $2k in these heads. $1500 shipped FIRM. Shipping to the lower 48 only.
Zach
Last edited by LT1Formula; 07-08-2014 at 11:14 PM.
#5
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: Lloyd Elliott AFR 1040's AGAIN
If I decide to build a 383 stroker I just may...good luck with sale for now
Trending Topics
#15
Member
iTrader: (1)
Join Date: Feb 2012
Location: vicksburg,mississippi
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 z28
Engine: 350 hsr
Transmission: probuilt 700r4/edge 2800
Axle/Gears: stock 4th gen 3.23
Re: Lloyd Elliott AFR 1040's AGAIN
What part of Texas are you located in? I live in Mississippi so maybe I could do a local pickup if you aren't too far?
#17
Member
Join Date: Jul 2011
Location: Delaware
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 Firebird, 91 Trans Am
Engine: L31 with HSR, LB9
Transmission: 700R4, 700R4
Axle/Gears: '99 10 bolt 3.90, '01 10 bolt 3.42
Re: Lloyd Elliott AFR 1040's AGAIN
Are guide plates included or they come as is?
Thread
Thread Starter
Forum
Replies
Last Post
355tpipickup
Tech / General Engine
5
09-28-2015 05:50 PM
355tpipickup
Tech / General Engine
9
09-13-2015 11:35 PM