Need to build a Wooden Engine Cradle
07-30-2010, 09:19 AM
#1
Junior Member
Thread Starter
Join Date: Dec 2008
Location: Hatboro, PA
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS
Engine: 87 350 2bolt main
Transmission: Looking for new 700R4
Axle/Gears: 3.23
Need to build a Wooden Engine Cradle
Help. I'm picking my engine up on monday and need a engine cradle to transport the engine home. I would like to build a simple wood cradle using 4x4 , 2x4 and traditional lag bolts.
Does anyone have plans or dimensions to build one?
Does anyone have plans or dimensions to build one?
07-30-2010, 11:03 AM
#2
Supreme Member
iTrader: (1)
Join Date: Jul 2004
Location: Calgary, AB, Canada
Posts: 10,763
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Re: Need to build a Wooden Engine Cradle
Is this going in the back of your truck?
If so, i'd just pile 2x4's under the engine mount brackets, and rest it on there. Then just strap it down if you like. It's 700lbs, sitting on it's engine mount brackets it's not going anywhere...
If so, i'd just pile 2x4's under the engine mount brackets, and rest it on there. Then just strap it down if you like. It's 700lbs, sitting on it's engine mount brackets it's not going anywhere...
07-30-2010, 12:31 PM
#3
Member
iTrader: (2)
Join Date: Feb 2007
Location: Byron, Illinois
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 camaro RS
Engine: superchargered 350
Transmission: t56
Axle/Gears: 4.10
Re: Need to build a Wooden Engine Cradle
I just had mine sitting inside of a old tire when i picked mine up
07-30-2010, 12:48 PM
#4
Moderator
Join Date: Jul 1999
Location: 51°N 114°W, 3500'
Posts: 17,106
Likes: 0
Received 120 Likes
on
101 Posts
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: Need to build a Wooden Engine Cradle
four 2x4 longer than the oil pan. two 2x4 wider than the oil pan
2 long ones on the floor. the 2 short ones across both ends. The last 2 long ones on top of the short ones. If they're just wide enough for the oil pan to fit into, the pan rails will sit on top of the top 2x4's. It would be 6" deep and fit the majority of oil pans.
I've had a 400 SBC sitting in a similar cradle for about 10 years.
As mentioned above, putting it inside an old tire can work also.
2 long ones on the floor. the 2 short ones across both ends. The last 2 long ones on top of the short ones. If they're just wide enough for the oil pan to fit into, the pan rails will sit on top of the top 2x4's. It would be 6" deep and fit the majority of oil pans.
I've had a 400 SBC sitting in a similar cradle for about 10 years.
As mentioned above, putting it inside an old tire can work also.
Thread
Thread Starter
Forum
Replies
Last Post
