Replacing stock 4x6's with 2 ways?
#1
Supreme Member
Thread Starter
iTrader: (10)
Join Date: Dec 2000
Location: Somewhere around the South Side of Chicago just crusin' in one of the Niteriders
Posts: 3,242
Likes: 0
Received 3 Likes
on
3 Posts
Car: 92RS 25th Anniv./88 IROC Z28 Vert
Engine: 305 TBI w/Tpi Air / 305 TPI
Transmission: 700r4/700r4
Axle/Gears: Posi
Replacing stock 4x6's with 2 ways?
I have some used 4x6 Pioneer TS P461 2 ways. I want to replace my stock 4x6's. The Pioneers have a two prong wire that comes out the Tweeter. I also need to run a two prong wire from the woofer as well. Can I splice the woofer and tweeter wire into the wire that runs to the stock radio? Or do I need some type of crossover?
Last edited by 86NiteRider; 05-16-2010 at 09:38 PM.
#2
Supreme Member
iTrader: (1)
Join Date: Mar 2007
Location: Arlington, Tx
Posts: 3,525
Likes: 0
Received 6 Likes
on
5 Posts
Car: 91 Camaro RS
Engine: empty bay (for now)
Transmission: Built T-56
Axle/Gears: 3.42 stock posi disc
Re: Replacing stock 4x6's with 2 ways?
To get a decent sound you need a cross over. It kinda defeats the purpose of having a separate woofer and tweeter if you send the same frequencies to them both.
#4
Supreme Member
Thread Starter
iTrader: (10)
Join Date: Dec 2000
Location: Somewhere around the South Side of Chicago just crusin' in one of the Niteriders
Posts: 3,242
Likes: 0
Received 3 Likes
on
3 Posts
Car: 92RS 25th Anniv./88 IROC Z28 Vert
Engine: 305 TBI w/Tpi Air / 305 TPI
Transmission: 700r4/700r4
Axle/Gears: Posi
Re: Replacing stock 4x6's with 2 ways?
Any recommendations on brands and potential cost? Also where should I place the crossover as in best location so I have no rattles?
#5
Supreme Member
iTrader: (1)
Join Date: Mar 2007
Location: Arlington, Tx
Posts: 3,525
Likes: 0
Received 6 Likes
on
5 Posts
Car: 91 Camaro RS
Engine: empty bay (for now)
Transmission: Built T-56
Axle/Gears: 3.42 stock posi disc
Re: Replacing stock 4x6's with 2 ways?
Everyone will have an opinion on what they think the best crossover is. Its all mostly personal preference. I dont run a crossover so I cant suggest what I use. However, it doesnt matter where you put the cross over, just know that it takes one input wire for each speaker, and has 2 outputs per speaker with 2 wire per output. (hi and mid/low, pos & neg). So its usually easier to mount them near the speakers so the youre not running a lot of wires through the car.
#6
Supreme Member
Thread Starter
iTrader: (10)
Join Date: Dec 2000
Location: Somewhere around the South Side of Chicago just crusin' in one of the Niteriders
Posts: 3,242
Likes: 0
Received 3 Likes
on
3 Posts
Car: 92RS 25th Anniv./88 IROC Z28 Vert
Engine: 305 TBI w/Tpi Air / 305 TPI
Transmission: 700r4/700r4
Axle/Gears: Posi
Re: Replacing stock 4x6's with 2 ways?
Everyone will have an opinion on what they think the best crossover is. Its all mostly personal preference. I dont run a crossover so I cant suggest what I use. However, it doesnt matter where you put the cross over, just know that it takes one input wire for each speaker, and has 2 outputs per speaker with 2 wire per output. (hi and mid/low, pos & neg). So its usually easier to mount them near the speakers so the youre not running a lot of wires through the car.
Thread
Thread Starter
Forum
Replies
Last Post
Ghettobird52
Tech / General Engine
15
12-29-2023 08:23 AM
db057
TBI
10
08-11-2015 10:11 PM