Power Adders Getting a Supercharger or Turbocharger? Thinking about using Nitrous? All forced induction and N2O topics discussed here.

Hey TTA guys.... plenum?????

Thread Tools
 
Search this Thread
 
Old 04-21-2004, 07:25 PM
  #1  
Member

Thread Starter
iTrader: (1)
 
2QUIK4U's Avatar
 
Join Date: Feb 2004
Location: Wisconsin
Posts: 438
Likes: 0
Received 0 Likes on 0 Posts
Car: 1991 Z28
Engine: 5.7 TPI L98
Transmission: 700-R4
Axle/Gears: Moser 9" with 4.11
Hey TTA guys.... plenum?????

A guy i work with drives an 87 GN. He heard about this thing called a plenum, which is some kind of plate that fits on his intake and smooths the air-flow and reduces lag... When i think of plenum i think of my TPI. He was explaining some plate with different slots and holes cut out... You guys ever hear of this mod???? Is it worth his money??
Old 04-21-2004, 10:53 PM
  #2  
Member
 
Greasemonkey's Avatar
 
Join Date: Oct 2001
Location: Anderson, IN
Posts: 414
Likes: 0
Received 0 Likes on 0 Posts
Car: 86 Cutlass
Engine: 350
Transmission: 200-4R
The RJC Power Plate. It goes BENEATH the plenum. I put one on my dads GN along with the Precision Plenum (according to the maker the best setup). Unfortunatly, I can't give any real results, as there have been a lot of problems with the car, not due to the plate. Most Buick guys like em, they're about $50 and while results vary, most have been able to get an extra lb or two of boost in before knock.
Old 04-22-2004, 10:39 AM
  #3  
Member
 
Bill87GN's Avatar
 
Join Date: Jul 1999
Location: Boston
Posts: 107
Likes: 0
Received 0 Likes on 0 Posts
Definitely worthwhile mod. For 50 bucks you can't go wrong and anything that evens out the airflow to all the cylinders, especially to those rear two.
http://www.rjcracing.com/RJC_Buick_P...wer_plate.html

Check out their other products too. Top notch quality and excellent service
Old 05-10-2004, 06:03 PM
  #4  
Member

iTrader: (3)
 
t-top89's Avatar
 
Join Date: Dec 2001
Location: midwest
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
the PP is a very good mod because is distributes the air evenly.

Goes between upper( dog house ) and lower plenum.

All of my plugs burn even and the 02 #'s are the same. 93 pump gas after the install and I ran 18psi 0.0KR on street..... Strip... same set up I ran 12.91. @108 0.0kr bad short time of 1.99 and that was the first time out.

Thrasher 92, THDP,TA49, 50# inj., street tires,and restalled stock vert.

Good mod in my book



Bo
89 turbo trans am
Old 05-16-2004, 05:46 PM
  #5  
Supreme Member

iTrader: (1)
 
fly89gta's Avatar
 
Join Date: Dec 1999
Location: Mays Landing NJ
Posts: 4,335
Likes: 0
Received 4 Likes on 4 Posts
Car: 2018 Camaro SS
Engine: LT1 w/Paxton 1500SL
Yes it's worth it.

You gotta tune for the leanest cylinders. This kinda puts all the cylinders on the same playing field so to speak(for lack of a better term)
Old 05-16-2004, 09:16 PM
  #6  
Member

Thread Starter
iTrader: (1)
 
2QUIK4U's Avatar
 
Join Date: Feb 2004
Location: Wisconsin
Posts: 438
Likes: 0
Received 0 Likes on 0 Posts
Car: 1991 Z28
Engine: 5.7 TPI L98
Transmission: 700-R4
Axle/Gears: Moser 9" with 4.11
thanx for the tip.....
boy, am i thirsty for a frosty Samual jackson beer.
Old 05-17-2004, 05:14 PM
  #7  
Senior Member

 
TTA850's Avatar
 
Join Date: Jun 2000
Location: NY
Posts: 645
Likes: 0
Received 0 Likes on 0 Posts
Car: 2013 C63C
Engine: M156 (P31)
Transmission: 7 speed MCT
Axle/Gears: AMG Limited Slip
I also have one on my car and it seems to work well. And dont belive anybody that tries to tell you it's a restriction in airflow, the maker of the peice has gone 9.96@133 with it and I've personally gone 10.69@125.8 with it. I think it's one of the reasons I've been able to run so well on pumpgas too, at 19psi, nothing but 93 octane in the tank, and 0.0 knock I've gone 11.20@119 w/1.55 60ft and 11.22@120 w/1.58 60ft.

HTH,
Steve
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
tglennon11
Electronics
10
09-23-2015 05:30 PM
Jk_Under
Tech / General Engine
1
09-08-2015 08:13 AM
apie2546
Tech / General Engine
8
09-05-2015 07:40 PM
90formulaVortec
Tech / General Engine
1
09-03-2015 09:26 AM
Jackrabbit501
Electronics
1
09-02-2015 09:14 PM



Quick Reply: Hey TTA guys.... plenum?????



All times are GMT -5. The time now is 08:51 AM.