92KRVZ28

Running 1000+ hp is very well possible. i have a friend whos twin turbo c5 made over a 1000 at the rear and he drove around on nice days in town highway he even drove it to the track to race.

mattsv8_03

iTrader: (2)

here in columbus there are at leat 10 cars i know of over 1000 whp. some are over 1200 and they are street cars. mor than they are raced.
3 are z06 on just went 9.66 at 155 on 9lbs of boost with 16 lbs made 1240 whp. he is on dr so bad 60 ft mid to high1.5s

TA88GTA

The house is a CSR piece. But a shaved a ton of material off the backside to get it to clear the iac housing. I shaved material off my HSR to make it clear the stock hood and shorten the runners so i have alot less room from the thermo housin to iac housing than you would normally have. The csr piece should work fine for you and if not just shave it, there is tons of material u can remove safely.

TurboedTPI

Very nice looking setup. No #'s yet?

hot92RS

Very clean. This is one of the nicest jobs that I have ever seen. Lot of forethought and even more skill shows in this project.

TA88GTA

Thanks,

Comfirmed tuning dates are now set for the 25 and 26 of this month. Will post numbers soon as there out.
On another note ive be doin some minor street tuning to shake out the bugs before the big day. U butt dyno says shes got got ***** lol. roll on to about 5psi at half throttle in third gear and it looks it someone hung two black paint brushes off the back bumper.

noroxus

iTrader: (1)

ha nicely put, looking forward to the numbers.
~Jeff

weberflorida

iTrader: (2)

Really nice looking man

lt1z350

iTrader: (2)

sorry havent been on in a few weeks. Here is a few of my project that is almost done. I have uploaded pics and it wont let me reupload them. How do I move them over here from the thread "post your single turbo set up pics here" ? Any way you can see them there attached to my name lt1z350. or if someone tells me how or can do it for me and move a few over here.

Street Lethal

iTrader: (16)

^ You have to attach them using the new thirdgen.org link. Double click the attachment you made in the original post, then right click on it to cut and paste it's new properties....

TA88GTA

So quick update. The car dynoed thursday friday along with a T trimed 421 camaro and badass Grand National. Thought the car was ready but of coarse if your gonna have problems, your gonna have them at the worst possible time. Anyways first day was shot after the plug wires caught fire and roasted some wiring. Over half of friday was wasted casing a possable fuel issue which turned out to be a spark issue. And once all that was figured out the and the car was again running on all cylinders we cased a boost issue for the rest of the day which still remains to to be sorted out. The problem is we would set boost at 20psi and it would boost to 5psi immediatly and then creep in to 14/15psi max over the rpm band. The boost controller wasnt working correctly and i believe the wastegate springs are too small for the boost we were trying to achive so were gonna give this another try to after i up the WG springs. At 15psi the mustang dyno is telling me were putting out 630 to the wheels but im not gonna concern myself with the numbers untill the problems are sorted out.
Also anyone ever used a mustang dyno. Owner of the grnd national told me he talked to a few people who said they call it the soulcrusher cause the tend to read low. Just wondering if anyone knew if there was some truth to this.

quadgoat

iTrader: (1)

Awesome buildup man! I'll be keeping an eye on this one!

As for Mustang Dynos...yes, the general consensus is that they do read lower than DynoJets and such. However, IMHO, they are more repeatable, and, since they are a loading dyno, much more useful for fine tuning drivability. Most people say they read about 30 HP "low", but the difference may be larger at your HP levels

-Paul

TA88GTA

I see, thanks for the info. Either way, who is to say if the mustangs are reading low or the others are reading high.

quadgoat

iTrader: (1)

Very true The most important thing is that you pick your dyno and stick with it throughout your tuning. That way when you make changes you can see whether you gain or lose power. "Dyno racing" is a somewhat pointless waste of time

-Paul

TA88GTA

So the boost issue is fixed. Problem was just lack of spring pressure in the gates. Car spools perfect now. Will have final numbers soon.

TA88GTA

Hey guys, update on the car is i had her back on the rollers for the second time and she put down 788@ 19psi. Ended up battling and few more issues and running outta time but im happy thus far and ill be bringing her back for the 20+ psi tuning. I had dyno video which i was gonna post but it got recorded over accidentaly. I do have some street video, so here you go. The last vid is a 4th gear roll on throttle and an accidental lane change at about 130km. Sorry for the shoty camera work but i dont blame him for wanting to grab the cage at that point lol. 1st through 4th are useless without the traction control setup.
Enjoy!!!

dark_daku89

whoa!!!

AC

iTrader: (3)

Holy SNART, I just SHART myself. Very nice man. Damn, turbos are so much fun it seems. They "almost" pull me away from buying my F1 procharger this spring.

drknow90rs_ss@y

iTrader: (3)

Awesome! So, youre running xfi? What are your intercooler dimensions? Thanks!

online170

:O thats a very clean car. I didnt think the rest of it would be that clean

Looks scary, and it doesnt look like you were gassing it much. Prolly not a bad idea to get some track time with it to 'really' practice driving....

Very very nice.

Plus... I know someone will ask down the line, so ill go ahead and ask now anyway. Size, dimensions and make of wheels and tires? Those look amazing on the car!

KJZ28/TA

iTrader: (1)

I was going to ask the same question^^^^^ THose wheels are awesome!!! But the whole car of course is just amazing!!! You must have fun in that car!!

TA88GTA

Yes im running the FAST XFI w/ traction control and the intercooler dimensions are 30/12/3.5

Tire sizes are 19by10.5 rear and 19by9.5 fronts. Backspacing was measured wrong so im running a 1/4spacers all around to make them work

Thanks for all the compliments again guys its been a few years in the making but shes almost done.

Demon355

iTrader: (1)

That thing is truly a badass machine. You can hear the boost coming in and then seeing the nose of your car dart into the next lane hahah priceless!

drknow90rs_ss@y

iTrader: (3)

Thank you, TA88GTA! What kind of mods did it take to get it to fit? (Other than lowering the radiator) Love the car!

TA88GTA

Well other than cutting all of the lower rad support out and lowering the rad, we trimmed the upper rad support which you can see in the first vid and welded the mounting tabs to the sides of the IC. Really didnt take much work. We installed threaded inserts right in the frame rails so the mounting plates sit flat on the bottom side of the rails and are bolted right to them.

online170

how is your quest going for fresh air? I know you wanted to cut up the front a bit and feed it some air.

TA88GTA

Actually pretty good, we fabbed up an aluminum air scoupe that catches and diverts air to the IC and rad seperatly. It been workin pretty well but hangs a little low so were gonna fab a new one that doesnt scrape driveways as much.

icebird84

so no cooling or airflow problem ?

scoupe is it Mounted on the cooler or inside the nose

TA88GTA

No problems at all. Im running a restricter plate instead of a thermostat, after havin a stat stick closed on me. Car runs at about 180 max. The scoupe is mounted inside the nose and just presses up against the IC and rad. Trimmed the bumper support to fit it.

online170

So trying to picture this.... if i stuck my head under the front of the car, i would see sorta "two air-dams"?
1 for rad, and 1 for IC?

67nova

Hey, your twin turbo setup is the bomb...Where can I get a set of those turbo headers?

TA88GTA

Well yes and no, the scoupe is one piece but has a diverter or air dam fro each cooler. Ill take a picture its easier for you to see than for me to explain.

67NOVA- sorry but you wont be able to find these headers anywhere but on my car, they were custom built.

1fas92

iTrader: (1)

Hello,
Do you have any closer pics of the headers. I was trying to get a closer look!

Thanks,
Robbie

allenfre

This is the cleanest set up I ever saw here since last week. I wonder how far can this one go knowing this has been stalled now for past 2 1/2 years

TA88GTA

Thank you.

and for the guys waiting for photos of the air diverter, you'll have to wait a little longer. I was making a few 180+mph pulls and the tack welds on the aluminum came unglued. guess the aluminum was a little to thin and tore around most of the welds. Lucky it didn't damage anything else. But ill have pics of the new one soon as its done.

11sec92z

That is the sickest twin turbo set-up in a 3rd gen I have ever seen !!!

allenfre

We'll be happy to see that thing evolve to a something awsesome. Thanks for keeping us posted

BMR Sales

Nice job, looks good!

drknow90rs_ss@y

iTrader: (3)

Any updates?

RED_DRAGON_85

subscribed

GodSpeedGTA

iTrader: (1)

Hey man, well done. I didnt mean to doubt you earlier but you put all the real doubters to rest. Awesome job, you obviously know what your are doing and what you wanted.

I only hope my single setup will measure up in some way. Again, Nice job!

BMR Sales

Damn car sounds good!

Orr89RocZ

iTrader: (20)

Havent read this thread in a while. Great build, I am hoping my setup turns out somewhat as nice as yours You've done very well with this build, I am impressed.

what i meant was he made over 500 hp naturally aspirated before the turbos were on. Thats with 8 to 1 compression. I find that amazing because my 383 was over 11 to 1 built for power with a fair sized cam and i made around same 500hp. 8 to 1 should give up 15% in power or so. Or more. Thats an incredible n/a 383 to make that power at 8 to 1

1320_Guy

iTrader: (3)

I would also like to see a few pics of the headers.

Duratys

Nice clean car to start off with....Impressive work!

91z 2 8

that thins is BAD ***!!! Seeing clean TT 3rd gens AND 6spd make me wish i was loaded on money and could afford to build one. What kinda blow off valve do you have? or do you not have one?? Sounds bad ***

lt1z350

iTrader: (2)

get it down the track yet? just curious what it would run at that power level. I am not running close to that much boost and close to those numbers with a single turbo setup and 383. What is the rest of the motor? heads cam compression so on. My car seems to be a freak of nature for how fast it is on 6 lbs I have played with 10 lbs on the street not the track yet and am going above and beyond my 42 lbs injectors and cant get the afr right so have to keep it at 6 lbs. even at a 13 to 1 lean on 10 lbs feels like 100 more hp though. cant wait to start playing with 12 to 15 lbs on it but need more fuel first. What injectors your running and rest of fuel system. I am sure I will hit similar power levels and looking to see what i might need . I might be making more than I think as the car is heavy and fast. Right now dont want to put it on the dyno afraid to blow up hte rear as on the street or track it spins alot and think that is saving the rear end. on the dyno and not spinning might kill it. If you can go down all your combo that would be great. thanks.

Orr89RocZ

iTrader: (20)

i didnt think 42lb injectors could do over 500whp? most guys run 60's for 600-700whp. My buddy maxed out (100% cycle duty) 60's at lsx pressure (makes them like 72lbs) at 708whp.

Street Lethal

iTrader: (16)

Am I reading this right....?

1fas92

iTrader: (1)

Hello,
I would love to see that car in person! I will be in Vancouver, WA in July this year! I know you live in Vancouver, B,C, Canada would it be possible to see your car?

I live in Carrollton, TX which is a suburb of Dallas, TX. I will be a long way from home! And would love to take a look!

I guess let me know!


I am in the process of building my twin turbo 92 Z28.......

Thanks,
Robbie
1fas92