Suspension / ChassisQuestions about your suspension? Need chassis advice?
Welcome to ThirdGen.org!
Welcome to ThirdGen.org.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!
while it may not be the best thing for the balljoint or swaybar endlink... IF you are careful then sometimes putting the jackstands underneath the a-arms works out much better and gives you more room to work on underneath. It's possible to set it up so the jackstands don't break anything there, Just an idea.
LOL, oh great, so you're one of the few that actually knows what a piece of crap my car is. I'll send you a PM, I don't think I've ever seen your car around here.
why is this not a sticky yet?
This is by far the best post i've ever read, (espescially related to suspension...)
I regularly use the spring perch as a stand point, it gets the car much higher as the front suspension doesn't unload and "drop" as when you use the frame for example.
Thanks Cayse! (now where's the rear suspension one?)
In various other threads, the question has come up on what size the endlinks should be when lowering a car. I was able to determine through some (rough) measurements, that the FRONT endlinks should be about 1/4" shorter for every inch the ride height is dropped. (It's actually a little under 1/4" for a little over an inch of drop, but these numbers will suffice). So for the Prokit springs, 1/4" shorter, and the Sportlines 1/2" shorter.
And wouldn't you know it, the Prothane endlinks that Spohn sells are about 3/8" shorter. This means they are perfectly fine for both Prokits AND Sportlines.
Again these numbers are approximate, but the swaybar position can be off a bit and not affect performance, so I don't see it being a problem. I haven't taken a look at the rears yet.
Excellent post on front end parts. I got the front end kit from Spohn and I think they use heavy duty tie rod adjust sleeves. Thanks again for the class.
OK, OK I hear you. I have not seen this thread, as it is a couple of years old now. When I started looking through it, I thought wow, how did this one get by. Thanks CaysE.
You really shouldn’t jack under the sway bar bushings. If you’re lucky you’ll just crush them slightly causing them to bind, if you’re unlucky you’ll bend a preload into your bar.
Jacking and jackstands under the control arms is sometimes the best way of doing things, just make sure you’re very careful to place them in a way that they can’t move/slide off.
Finally, the end link lengths would be a lot more useful with actual lengths, rather the x shorter than stock, since I doubt many of us could come up with a stock endlink at this point anyway and I’d bet that most “stock replacements” are all sorts of different lengths..
Not that I know of… the reason is that it will move various suspension points outside of the wheel lips making the car extremely dangerous if you had a flat tire.
...the end link lengths would be a lot more useful with actual lengths, rather the x shorter than stock, since I doubt many of us could come up with a stock endlink at this point anyway and I’d bet that most “stock replacements” are all sorts of different lengths..
The only part of the endlink of concern is the spacer sleeve in the middle. The Prothane spacer is 1+3/4" long, while the stock spacer (on a '92 RS) is ~2+1/8" long. As long as there's enough thread on the bolt, you can continue to shorten the sleeve about 1/4" for every additional inch the car is dropped to keep the swaybar flat (1+3/8" sleeve for a 3" drop in front, for instance).
Very useful tips. As far as a good place to find stock replacemnet parts, Moog offers high quality replacement parts that are much thicker and beefier in most cases that stock.
i got some REALLY NICE 1LE endlinks off of TDS awhile back... i think they were like 40 bucks apiece, but they're zinc-coated and really beefy with some stiff nylon bushings that's lasted a year and a half now and still look great. they were at least a 1/4" shorter than the ones i took off the car, but work fine on my stock height car. nothing but a 36mm sway and wonderbar up front.
Saw a post requesting a picture with the IROC replacement springs installed. I bought the springs from NAPA for a bit under $70, other new parts installed but the ride height was not affected by that. The springs raised the car at least an inch too high, I'm hoping it will sag an inch or so pretty quick. (Poor picture, poor digital camera)
Finally, the end link lengths would be a lot more useful with actual lengths, rather the x shorter than stock, since I doubt many of us could come up with a stock endlink at this point anyway and I’d bet that most “stock replacements” are all sorts of different lengths..
I read in "How to Make Your Car Handle" that the spacer length is determined by keeping the sway bar parallel to the ground at ride height.
tips on removing coil springs without the factory J-23028 tool, and should i go with stock z28 coil spring or go iroc springs?
Warning you can kill your self. If at anytime you feel unsafe or something is going to slip STOP.
With the car on jack stands. stand placed on frame rail inline with door hinges.
remove sway bar links.
remove nuts for the a-arm to frame bolts. Then put a floor jack under the spring perch. Lightly jack up perch untill tension of off the a-arm bolts. Remove the bolts.
Carefully lower the jack. The springs should be loose.
loosen the top nut for the strut. make sure there is no spring pressure on the strut.
remove the nut.
remove springs.
If your putting the sportline springs in. You can install the strut nut. And then put springs into the sub frame. The stock springs are longer and will not fit, unless the strut is off as well.
i have a 87 berlinetta... i know sorry. but i have 245/55/16 mounted on WS6 wheels on the back and 215/55/16 up front. now when i pull outta my drive way or where evere with my wheels turned it rubs.
Now i was wondering if IROC's had different contorl arms?
My friend has 245's up front on his and they dont rub
here's my thoughts. 1st, are your front struts good? they can get week and lower front end a little bit. after that i'd say, my 87 iroc rides on 225/55/16 on front and 255/55/16 on back. i have original rims. my front right only rubs cause i need to screw/secure the wheel well liner back down. this means i only have 1/4 inch clearance. so really my tires don't rub. i don't know about other makes like rally or berlinetta being different. i'd say sell it and get a Z28 3rd gen. ha ha ha. good luck...
lightwolf - Your car is probably a coupe as the Berlinetta was discontinued in 86...... More to the point: Are the 16" wheels on the front of the car marked "FRONT". The 16" wheels have different offsets for the front and rear wheels. Factory 16" wheels should NOT be rubbing.
If the correct wheels are installed on the right hubs than it's possible there is some damage somewhere causing the rub. The control arm, fenders or even the frame might be "tweeked' just enough to cause the tires to rub when cornering. It could also be a problem with the internal "stops" inside the steering box or improperly installed tie rods. On some F-Body's I'v owned the front wheels will SLIGHTLY rub on the plastic fender well - but that is usually the result of the plastic fender well being a bit warped or installed wrong.
Take a good look at the front end and find out exactly where the rub is occuring......it might help lead you to where the problem is originating !
i know this is an old post, but im kinda new to this forum. I have a 87 camaro that im trying to get the factory front coil springs back into. do i just un bold the a-arm to put the spring back in? or will i need some kind of compressors? the inner type? THANK YOU so much!! I really need help!!
i know this is an old post, but im kinda new to this forum. I have a 87 camaro that im trying to get the factory front coil springs back into. do i just un bold the a-arm to put the spring back in? or will i need some kind of compressors? the inner type? THANK YOU so much!! I really need help!!
Lol good question to end on?? How did u do it then?
Unless he unbolted the a-arm and then used a jack to compress the spring using the weight of the car, he would have needed to use the inner type spring compressor.
Unbolting the A-arm is a piece of cake for drop springs, but putting stock ones in takes some struggling since they're pretty tall.
I have a parts car almost down to the shell. I had taken the drivers sd spindle off , but never dropped the A arm bolts (just at the ball joint). It wasn't pretty. As I dropped the jack down and the A arm started to swing towards 90 degrees the spring still had some tension. So I pry it out till it shot like a bullet. It did hit my hand but dint hurt too bad. Funny thing was that I learned thats not the best way to do it lol.
I got 200k on my set up, & thought struts would be good but reading on, springs are recomended a lot. Darn it. So one inch lowering springs will give me stock ride till they are broke in, and sag some???
Last edited by STRIKER911; 10-23-2009 at 02:03 PM.
Reason: Wrong
I would do dampers and springs at the same time and make sure they complement each other. For example, KYB GR-2 or Koni reds would match well with Eibach Prokit springs, but would wear out faster if matched with Sportline springs which are lower and softer.
If you only have money to do one or the other, I would do struts and shocks first.
Springs don't settle THAT much. The issue is that stock springs have sagged over time so they're already lower than they were when new, so lowering springs sometimes don't look like they lowered the car. Handling will be greatly improved though.
I would do dampers and springs at the same time and make sure they complement each other. For example, KYB GR-2 or Koni reds would match well with Eibach Prokit springs, but would wear out faster if matched with Sportline springs which are lower and softer.
If you only have money to do one or the other, I would do struts and shocks first.
Springs don't settle THAT much. The issue is that stock springs have sagged over time so they're already lower than they were when new, so lowering springs sometimes don't look like they lowered the car. Handling will be greatly improved though.
Thanks for the info. Helps a lot since I was thinking that the one inch lowering springs would be the way to go. Since I did put the kyb gt2's on it this summer That would have not been a good match. So ya, thanks.
Id love the car to handle better then stock, but shoot its so much better then the mustang I have with everything being worn. lol. So im good as long as its better then what it is now, with 200k on everything except the struts, and shocks.
I had posted this question elsewhere ( to no response ) so I thought I'd try it here.
What is the preferred camber setting for a typically driven OEM outfitted (a-arms, spindles,struts) street car?
I've read about an adjustment to the factory spec that helps reduce the excessive outside tire wear common with the 3rd gens.
Twice now I've rebuilt front ends on these cars, ALL componenets replaced right down to the a-arm bushings and strut mounts and gone to a reputable shop to have an alignment done. Both times I end up with premature outside tire tread wear. The vehicle does have a 2" dropped spring set. Could the problem be there?
I had posted this question elsewhere ( to no response ) so I thought I'd try it here.
What is the preferred camber setting for a typically driven OEM outfitted (a-arms, spindles,struts) street car?
I've read about an adjustment to the factory spec that helps reduce the excessive outside tire wear common with the 3rd gens.
Twice now I've rebuilt front ends on these cars, ALL componenets replaced right down to the a-arm bushings and strut mounts and gone to a reputable shop to have an alignment done. Both times I end up with premature outside tire tread wear. The vehicle does have a 2" dropped spring set. Could the problem be there?
Yep thats the deal dude. If u lower it then factory numbers wont work. I know at firestone they go by factory settings. I know cause I had to yell at the manager one day when i got mine worked on. Still pulled to the right. he said "well we get our info from the book" lol. U can also read this thread for more info.
If you want truly proper adjustment with a 2-inch drop, it's best to get some LCA relocation brackets welded up, and do the whole package for the rear: adjustable LCAs, adjustable panhard bar, and adjustable torque arm. For the front, you probably need to modify your toe setting if you have outside wear. Typically, a drop will induce negative camber, causing more wear on the inside, but the steering arms will cause more toe-in.
Have you noticed if the strut mounts are at full negative camber when you have outside wear?
Can someone list all the tool recomended to do this job? Further more I have had yet to find a front end kit that includeds a pittman arm. If I do this job myself i would have everything off and am wondering why wouldn't I replace the pittman while I was doing all this. Do they generally not go out?
Can someone list all the tool recomended to do this job? Further more I have had yet to find a front end kit that includeds a pittman arm. If I do this job myself i would have everything off and am wondering why wouldn't I replace the pittman while I was doing all this. Do they generally not go out?
The pitman arm doesn't have a bushing or bearing in it, so there's no need to replace it.
This isn't just one job, really (unless you're replacing absolutely everything). Most of the time, people will replace the steering links or the swaybar, and you would need a few wrenches and sockets for either, and a grease gun for the steering links. A-arms are more involved, since you'll need a press to change the bushings and ball joints.
I'll send you a PM, I don't think I've ever seen your car around here. 
Any input about air vs. gas struts(front, of course) on an 87 iroc z28.i put air shocks on rear end. how is the ride with air struts, bouncy? 
