Body shell or roller needed
#1
Body shell or roller needed
I am restoring my 85 Bird that only needs the body shell for an automatic transmission. I live in SW Ohio near Dayton. I have some transportation for pick up. I HAVE hood, fenders, 2 hatch backs, front and rear suspension , engine,automatic transmission , rear end and wheels. I will consider anything .Thanks, Frank
Last edited by windsurfer; 08-05-2014 at 12:23 PM. Reason: additional information
#2
Moderator
Join Date: Jul 1999
Location: 51°N 114°W, 3500'
Posts: 17,110
Likes: 0
Received 120 Likes
on
101 Posts
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: rolling chassis needed
A rolling chassis in a third gen is everything except the engine/transmission. There is no removable chassis. It's all part of the body.
What exactly are you looking for?
If you have just a body then you need all the suspension components and yes they are all interchangeable from 82-92
What exactly are you looking for?
If you have just a body then you need all the suspension components and yes they are all interchangeable from 82-92
#3
Re: rolling chassis needed
Yes I need the body without the fenders, hood, doors and hatchback. I understand it is unibody but did not know how to describe what I need. I have the steering , rear springs, engine tranny and rear end. Thanks for the years that are interchangeable.
#5
Supreme Member
iTrader: (1)
Join Date: Aug 2008
Location: Short Summer, VT
Posts: 1,485
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1985 Trans Am T-Top
Engine: 305 TPI
Transmission: T-5 5 Speed
Axle/Gears: 3.42 posi 1LE 10 bolt
Re: rolling chassis needed
Ok, you need a new body, any year will work, I would stick with an 85-90 just because I think they are slightly better sorted out that 82-84.
You should specify ttops or not and auto or manual trannys.
You will also need to post your location , not like it's going ups.
You should specify ttops or not and auto or manual trannys.
You will also need to post your location , not like it's going ups.
#6
Member
Join Date: Dec 2011
Location: West Haven, Utah
Posts: 420
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 trans am
Engine: 350 TPI
Transmission: T5
Axle/Gears: 3.27
Re: rolling chassis needed
I have two body's shells, one is a t top titled GTA 1989 and the other is a hard top titled GTA. they have been in my shop out of the weather with ZERO rust anywhere. the t top is NOT a roller, it is stripped to its nuthins. the hardtop does have the rear axle and front end under it, other than that there is not a thing left on this body. Now the real question.... where are you?? cuz that can be a deal breaker for allot of people. I am in Utah.
#7
Re: rolling chassis needed
KBD85 Thanks , either one sounds like what i need. I live in SW Ohio near Dayton but I have friends that travel to pick up cars. I will check with them about transpo. In the mean time what do you need for either one? Thanks, Frank
Trending Topics
#9
Member
Join Date: Dec 2011
Location: West Haven, Utah
Posts: 420
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 trans am
Engine: 350 TPI
Transmission: T5
Axle/Gears: 3.27
Re: rolling chassis needed
well the hard top would be the one we could roll around if needed. i have them on a local site here for 200 for that one and 150 for the t top one. the reason i have the t top one lower, not only cuz there is nothing on it drive train wise, but it has a funny dent on the back floor near the hump. So if i was recommending one i would go with the hard top. I would want to send a bunch of pics first tho just to make sure your good with what it all looks like. Let me know, Ken.... oh and they are both set up for auto, nothing left if the t top one at all, like its stripped to the firewall. The hard top i cant remember if pedals are in there. I would have to look and see for ya.
#10
Member
Join Date: Dec 2011
Location: West Haven, Utah
Posts: 420
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 trans am
Engine: 350 TPI
Transmission: T5
Axle/Gears: 3.27
Re: Body shell or roller needed
Frank, i just sent you a PM with my email so I can send you some pics if you want
#11
Supreme Member
iTrader: (2)
Re: Body shell or roller needed
This guy has a decent roller up for sale:
https://www.thirdgen.org/forums/fire...ler-950-a.html
https://www.thirdgen.org/forums/fire...ler-950-a.html
#12
Re: Body shell or roller needed
OK Ken Sounds like the hard top is best. . Pictures of the under body is what I need most. What year is it? I will start looking for transpo. Thanks ,Frank
#13
Member
Join Date: Dec 2011
Location: West Haven, Utah
Posts: 420
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 trans am
Engine: 350 TPI
Transmission: T5
Axle/Gears: 3.27
Re: Body shell or roller needed
I think that one is the 87. when i get off work i will roll it out of the garage and get a plethera a pics for ya! email me if you would so i can send more at a time rather than fill this thread up with a bunch of pics. (my email is in a personal message under your name) ill also take a pic of the title for ya to see all the info there
Thread
Thread Starter
Forum
Replies
Last Post