Go Back   Third Generation F-Body Message Boards > Tech Boards > Tech / General Engine
Sign in using an external account
Register Forgot Password?

Tech / General Engine Is your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 09-28-2009, 08:31 PM   #1
Junior Member
 
Join Date: Dec 2008
Location: Chicago, Illinois
Posts: 53
Car: 1991 Camaro RS

Classifieds Rating: (0)
Send a message via AIM to wildviper44
how to change oil dipstick tube

hey i know this is probably one of the most simple things one can do on a car, but i've never done it and need to know exactly how. who can tell me how i would go about changing my oil dipstick, with the tube as well? because my current dipstick is from a junkyard and is a POS and leaks oil out near the bottom, so i needed a new one. i just bought a brand new oil dipstick with the tube and i don't know how i would go about installing it. i'm guessing the first step would be to jack the car up and get underneath it since it doesnt seem to be accessible from the top. do i have to drain oil first? or does it not matter if there's oil in the pan or not? all i have to do is unbolt that one bolt that mounts the tube and pull it out, and put the new one in and bolt it in the same spot, right?? thanks for any feedback
wildviper44 is offline vBGarage Page   Reply With Quote
Old 09-28-2009, 10:49 PM   #2
Senior Member
 
Join Date: Jan 2009
Location: Ogden UT
Posts: 742
Car: '88 Camaro (Gone...)

Classifieds Rating: (15)
Re: how to change oil dipstick tube

Thats correct, just remove the single bolt holding the bracket to the block and it will pull out. No need to drain the oil

--Are you sure it's the dipstick thats leaking and not a bad oil pan gasket? I don't see how the dipstick itself would leak?
Primetime91 is offline vBGarage Page   Reply With Quote
Old 09-28-2009, 10:50 PM   #3
Supreme Member
 
Pocket's Avatar
 
Join Date: Jun 2005
Location: NC
Posts: 6,038
Car: 92 Firebird
Engine: Supercharged 6.0
Transmission: 4L80E
Axle/Gears: 8.8 3.55 locker

Classifieds Rating: (19)
Send a message via AIM to Pocket
Re: how to change oil dipstick tube

There is only one anchor bolt

Remove it by gently twisting it out. It will not want to move but be gentle. You absolutely dont want to snap it off even or inside the block
Pocket is offline vBGarage Page   Reply With Quote
Old 09-29-2009, 10:06 PM   #4
Senior Member
 
Join Date: Jul 2007
Location: MA
Posts: 1,141
Car: '87 IROC/'68 SS
Engine: 5.7L/350
Transmission: 700R4/Muncie 4-spd
Axle/Gears: 3.27 9 bolt / 3.31 12 bolt

Classifieds Rating: (1)
Re: how to change oil dipstick tube

The challenge is in the access. Be patient and you'll persevere. :-)
jv9999 is offline vBGarage Page   Reply With Quote
Old 09-30-2009, 12:04 AM   #5
Supreme Member
 
Join Date: Dec 2005
Location: Macon, GA
Posts: 3,339
Car: 1992 Camaro RS
Engine: Vortec headed 355, xe262
Transmission: T56
Axle/Gears: 9-bolt 3.70

Classifieds Rating: (3)
Send a message via AIM to InfernalVortex
Re: how to change oil dipstick tube

Quote:
Originally Posted by Primetime91 View Post
Thats correct, just remove the single bolt holding the bracket to the block and it will pull out. No need to drain the oil

--Are you sure it's the dipstick thats leaking and not a bad oil pan gasket? I don't see how the dipstick itself would leak?
+1

I doubt it's the dipstick that's leaking unless it's broken/cracked or something... but even then... oil doesnt really travel up the dipstick where it goes into the block at all.
InfernalVortex is offline vBGarage Page   Reply With Quote
Old 09-30-2009, 08:52 PM   #6
Junior Member
 
Join Date: Dec 2008
Location: Chicago, Illinois
Posts: 53
Car: 1991 Camaro RS

Classifieds Rating: (0)
Send a message via AIM to wildviper44
Re: how to change oil dipstick tube

okay thanks for the replies. yeahh idk.. we'll see just where it leaks from. my friend said the dipstick but i haven't actually checked it out yet. about to go change the stick regardless here in a few minutes
wildviper44 is offline vBGarage Page   Reply With Quote
Old 09-30-2009, 08:52 PM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > Tech / General Engine

Tags
305, 3rd, 57, 700, body, broken, camaro, change, dipstick, genorg, oil, remove, replace, stick, tube
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 09:45 PM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.5.2
All content copyright © 1997 - 2012 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details