Tech / General EngineIs your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!
Welcome to ThirdGen.org!
Welcome to ThirdGen.org.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!
New starter, good batt, won't start, no lights, HELP
'86 305 auto....Son had car, ran rough, stalled , said he saw smoke, couldn't start, got towed.
Car had hard click and dome light worked, but wouldn't crank.
Replaced starter and now I have no click, no nothing, not even lights! Not even dome light. Any idea what I screwed up?
I placed two wires onto starter on same post as battery cable goes on and light weight wire on small stud nearest engine. Did all this with battery disconnected, then reconnected battery and...nothing.
Does not seem like any fuses are gone. Any ideas?
Thanks
Re: New starter, good batt, won't start, no lights, HELP
have u checked ur relays? also have u checked all the cables goin to the starter to make sure they weren't exposed wires loose nuts or bolts and there wasn't any corrosion on them? also may have a good batt but no juice?
Re: New starter, good batt, won't start, no lights, HELP
i believe that there are some fusible links close to the battery to check as well. you really need to give them a tug. lookin good isnt a good diagnosis. pull on them. get a test light and check the fuses for which has power (key on and key off) and which ones dont-it will start to steer you in the correct direction.
__________________ 1985 IROC Original Owner.Original silver paint, Roller 406c.i., 4 bolt, Superram, accel DFI 6. serpentine setup, Factory GM 1LE brake set-up, richmond 5 speed, 1 3/4 slp, jet hot, gale banks 2OTL power pack (vintage), eibach, grey leather flo-fits, A/C delete, 29k original miles and never been driven in the rain. all original parts are on the shelf. original window sticker and build sheets. 1996 Z28 M6 LT4 kit, hotcam, obd1, C5 brakes. And then theres the road runner.
Re: New starter, good batt, won't start, no lights, HELP
run a jumper wire from the solenoid start terminal up to the battery and try touching the battery positive terminal. by doing this you will take alot of wiring out of the loop and will see at least if you have good juice to the starter. make sure its in neutral if it is a manual tranny.
Re: New starter, good batt, won't start, no lights, HELP
if your solenoid is equipped with just a main battery (large terminal) and a start (small terminal) it is indeed the small terminal. some solenoids have an "r" terminal as well. for a total of 3 terminals. you want the small terminal closest to the block. with a flashlight you should see a small "s" molded into the solenoid as well.
__________________ 1985 IROC Original Owner.Original silver paint, Roller 406c.i., 4 bolt, Superram, accel DFI 6. serpentine setup, Factory GM 1LE brake set-up, richmond 5 speed, 1 3/4 slp, jet hot, gale banks 2OTL power pack (vintage), eibach, grey leather flo-fits, A/C delete, 29k original miles and never been driven in the rain. all original parts are on the shelf. original window sticker and build sheets. 1996 Z28 M6 LT4 kit, hotcam, obd1, C5 brakes. And then theres the road runner.
Re: New starter, good batt, won't start, no lights, HELP
You check your wiring that goes up to the starter? I once had a problem where nothing worked and eventually found out it was a busted wire down going down to the solenoid and starter sucked bad...took over a month for me to figure it out...XD