Search



Go Back   Third Generation F-Body Message Boards > Tech Boards > Tech / General Engine
Sign in using an external account
Register Forgot Password?

Tech / General Engine Is your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!
Sponsored by Weld Racing
Click Here

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 10-17-2011, 06:20 AM   #1
Junior Member
 
Join Date: Dec 2000
Location: Los Angeles
Posts: 18

Classifieds Rating: (0)

Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

I've had what I thought was a classic head gasket problem: bad smell in the passenger compartment, bad smell from the exhaust pipes, unpredictable temp gauge action, sometimes a boiling, bubbling overflow tank, etc. And the radiator coolant level would slowly go down.

On the other hand....Other signs of head gasket problem seem to be "milky oil," and oil in the coolant -- neither of which I have. Performance-wise, the power is still good but the gas mileage does suck (12 MPG).

But then last week the sh#@% started hitting the fan. Actually, it started hitting the engine block. I drove the car about 6 miles and when i stopped steam started coming out from under the hood. I pop the hood and it turns out its coming from the top of the engine. Once it cools down, I add some water to the now bone dry radiator and I notice immediately water starting to trickle out and pool on rightside top of the engine block. The radiator level goes down as the water trickles down the engine. (When the engine was running and under pressure the water was probably gushing out, hitting the hot engine and steaming up.)

I've now looked at the engine and located a leak coming from the right front part of the intake manifold (see photos for location). So it looks like I have a bad intake manifold gasket. But is that my only problem?....which leads to my questions:

QUESTIONS: Would the symptoms I described be caused by just a bad intake manifold gasket? Or is it likely I do also have a bad head gasket? How do the symptoms for the 2 problems differ? And how can I be sure if it's one or both?
Attached Images
File Type: jpg T-A-Manifold-1.jpg (67.1 KB, 102 views)
File Type: jpg T-A-Manifold-2.jpg (62.2 KB, 87 views)
__________________
'89 Trans Am
350
WS6 w/Dual Cats
tsmash is offline vBGarage Page   Reply With Quote
Old 10-17-2011, 07:47 AM   #2
Supreme Member
 
Join Date: Sep 2010
Posts: 1,434

Classifieds Rating: (0)
Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

you don't have to worry because as you are replacing the head gaskets the intake manifold gasket gets replaced as well.

Also, since you were leaking coolant, you may have even given your bearing a nice bath in coolant.

Soooooo

replace the head gasket and while they are off, replace the valve seals

get as cheap of oil as possble and get 10 quarts and then 5 quarts of what you will end with.

You are going to have to change the oil 3 times to try and be sure you get out all of the coolant.


oh, please don't post that it won't fire up after you put it all back together. You stabbed the distributor in wrong. Just find TDC of cylinder 1 and wire it correctly.
torque_is_good is offline vBGarage Page   Reply With Quote
Old 10-17-2011, 08:19 AM   #3
Supreme Member
 
Join Date: Jun 2005
Location: Sydney, Australia
Posts: 1,365
Car: '86 TA
Engine: '74 350
Transmission: 700r4
Axle/Gears: 2.77

Classifieds Rating: (0)
Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

Do a compression test first before you start wrenching, to check the head gaskets. Looks like the intake gasket is leaking badly, that's a nasty looking mess.
TreeFiddy is offline vBGarage Page   Reply With Quote
Old 10-17-2011, 04:36 PM   #4
Junior Member
 
Join Date: Dec 2000
Location: Los Angeles
Posts: 18

Classifieds Rating: (0)

Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

I was actually happy when I discovered that the problem might just be the manifold gasket -- and not the head gasket. A bad head gasket seems to be a much bigger, and expensive, thing to fix (I won't be doing the work myself -- I have to pay a mechanic) -- so I was trying to avoid messing with the head gasket if I didn't have to.

That's why I asked if my symptoms go along with just the manifold gasket problem? I was trying to get an idea of the odds that that's my only problem before I start throwing money at it. So I'd appreciate it if someone could give me their best guess.

A compression test should determine that for sure -- right? But until I get that done, I'd kind of like to know what I might be getting myself into. Thanks.

Last edited by tsmash; 10-17-2011 at 04:55 PM.
tsmash is offline vBGarage Page   Reply With Quote
Old 10-17-2011, 06:21 PM   #5
Supreme Member
 
travis401's Avatar
 
Join Date: Mar 2007
Location: Arlington, Tx
Posts: 3,524
Car: 91 Camaro RS
Engine: empty bay (for now)
Transmission: Built T-56
Axle/Gears: 3.42 stock posi disc

Classifieds Rating: (1)
Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

head gaskets arent that expensive and its not at all hard to do with simple hand tools. the only specialty tool you need is a torque wrench. which you can rent from a local parts store. btw over the counter stock replacement head gaskets are like $30-$50 for a set. youre going to have to pay a mechanic about $200 min to do the job.
travis401 is offline vBGarage Page   Reply With Quote
Old 10-17-2011, 07:37 PM   #6
Supreme Member
 
Join Date: Jun 2005
Location: Sydney, Australia
Posts: 1,365
Car: '86 TA
Engine: '74 350
Transmission: 700r4
Axle/Gears: 2.77

Classifieds Rating: (0)
Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

A compression test should 99% rule out or comfirm a leaking head gasket. Easy to do, and much better to do some quick basic diagnosis rather than ripping things up when it may turn out to be unnecessary.

It could still be a head gasket leaking from a water gallery to the outside yet holding compression, but I would think very unlikely. Other possibilities are warped/cracked heads/block.

BUT since you don't have an oil milkshake, and you do have a big mess at the intake, I would start there. Leaking coolant can smell god-awful, and sounds like you have an overheating problem.
TreeFiddy is offline vBGarage Page   Reply With Quote
Old 10-19-2011, 04:07 AM   #7
Junior Member
 
Join Date: Dec 2000
Location: Los Angeles
Posts: 18

Classifieds Rating: (0)

Re: So how much should I pay to fix a Intake Manifold Gasket?

I'm taking the car in to the mechanic tomorrow to get the compression test and then to get the intake manifold gasket replaced (hopefully that's all it needs). So what's a fair price to pay a mechanic to get these 2 things done?
tsmash is offline vBGarage Page   Reply With Quote
Old 10-19-2011, 08:01 AM   #8
Supreme Member
 
TTOP350's Avatar
 
Join Date: Oct 2001
Location: central Il USA
Posts: 5,830
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt

Classifieds Rating: (4)

Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

I would also check the coolant hose that comes out of the lower pass side TBody right above the intake for pinholes.
TTOP350 is offline vBGarage Page   Reply With Quote
Old 03-31-2012, 12:50 AM   #9
Junior Member
 
Join Date: Sep 2011
Location: Strasburg, Pennsylvania
Posts: 46
Car: 1991 Chevrolet Camaro Z/28
Engine: 5.0L 305
Transmission: 700R4 W/ B&M shift kit
Axle/Gears: 3.23

Classifieds Rating: (0)
Re: Bad Intake Manifold Gasket or Blown Head Gasket? Or Both?

If your oil is milky your intake manifold gaskets are shot its the coolant leaking into your engine and mixing with the oil i just ran into this issue tonight while driving home and saw a trail of smoke and the oil/coolant was all the way up the dipstick none was coming out the exhaust but if you have smoke coming out the exhaust or notice an aggressive vibration as well as the milky oil chances are you got screwed with both problems but good luck hopefully it turns out to only be the intake gaskets
cactusman92 is offline vBGarage Page   Reply With Quote
Old 03-31-2012, 12:50 AM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > Tech / General Engine

Tags
bad, blown, compression, difference, gaskeet, gasket, gaskets, head, inlet, intake, lim, manifold, mess, symptom, symptoms, test
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 06:57 AM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.5.2
All content copyright 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details