Would you run these roller rockers?
#1
Junior Member
Thread Starter
Join Date: Oct 2006
Location: Manteno, IL
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Z28, yamaha vmax, and zuki vitar
Engine: TPI 350
Transmission: WC T5
Axle/Gears: 3.23 posi, soon 3.73
Would you run these roller rockers?
Hey guys was just looking around on fleabay and came across these 1.6 ratio ss self alighning rr new a for about 125! Would you guys run them? The seller has them in billet aluminium for the same price.
http://www.ebay.com/itm/1-6-7-16-SBC-Stainless-Steel-Self-Aligning-Roller-Rocker-Arm-Set-16-CNC-V8-350-/151154768310?pt=Motors_Car_Truck_Parts_Accessories&hash=item233186b9b6&vxp=mtr
http://www.ebay.com/itm/1-6-7-16-SBC-Stainless-Steel-Self-Aligning-Roller-Rocker-Arm-Set-16-CNC-V8-350-/151154768310?pt=Motors_Car_Truck_Parts_Accessories&hash=item233186b9b6&vxp=mtr
#5
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,040
Received 1,667 Likes
on
1,265 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Re: Would you run these roller rockers?
Looks a lot like yerbasic typical People's Liberation Army special.
No I would not run that.
No I would not run that.
#6
Moderator
Join Date: Jul 1999
Location: 51°N 114°W, 3500'
Posts: 17,110
Likes: 0
Received 120 Likes
on
101 Posts
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86
Re: Would you run these roller rockers?
Offshore copy of Comp Cams stainless rockers at 1/3 the price. Probably have 1/4 the quality and reliability. They may look the same but if you took it apart and compared it to a real one, it would probably be obviously different. Considering the only place the part number pops up is on ebay, I'd say they're not a brand that sells in regular performance parts stores.
In a bone stock engine with stock springs, they might work just fine but even then, they could fail or wear out in a short period of time. Want to use them in any sort of built up engine and I'd say no. Since you're buying rockers like this for performance, spend the extra money for a known brand rocker with some reliability and quality. Even the brand name entry level rockers will probably be a better choice than those.
In a bone stock engine with stock springs, they might work just fine but even then, they could fail or wear out in a short period of time. Want to use them in any sort of built up engine and I'd say no. Since you're buying rockers like this for performance, spend the extra money for a known brand rocker with some reliability and quality. Even the brand name entry level rockers will probably be a better choice than those.
Trending Topics
#8
Re: Would you run these roller rockers?
C'mon... You guys are being a little harsh, aren't you? I'd think those rockers would be good up to at least 0.7000 RPM and should handle lifts of at least 0.00500" at the valve, even over the famed full-race (why go half-race?) Monkey Spank springs.
Would I run the aluminum version? You bet, without hesitation! I'd run them right down to the local recycler - Aluminum is going for over 60¢ a pound right now.
Would I run the aluminum version? You bet, without hesitation! I'd run them right down to the local recycler - Aluminum is going for over 60¢ a pound right now.
Thread
Thread Starter
Forum
Replies
Last Post
junkcltr
Tech / General Engine
6
08-02-2019 11:12 PM