Third Gen Association of OntarioRegional message board for everyone in Southern Ontario and nearby regions.
Welcome to ThirdGen.org!
Welcome to ThirdGen.org.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!
Sold: Well actually traded for a front brake job on my 99 Jimmy when (if) I get the transmission fixed. *sigh* Alpine head unit, CD changer, amp, cross over, speakers and all wire except speaker wires.
Last edited by KnottyBuoyz; 06-28-2009 at 12:17 PM.
Selling a pre 1985 355 sbc bored .030 over, 2 bolt main, has corvette l98 heads with 3 angle valve job,mild cam. Only put 3k on the motor,did put down over 300hp with ported tpi intake.
- heads may need a rebuild and new gaskets
- needs new starter,have the old one but recommend a mini starter
- needs new dipstick tube
Asking $400 obo, picked up a newer vortec motor to build and need this gone as is.Would be great for carb intakes..efi didnt like the cam with tpi speed density with tuning.
New Moroso Stroker/Kick out oil pan - $200
New Moroso Pick-up - $50
New Melling hi-volume oil pump - $100 *Can have all 3 pump, pickup and pan for $300*
Holley/Barry Grant "claw" 750 Double pumper - $300 (new but needs rebuild)
V-belt March underdrive pullies - alt/w.pump/crank - $300 (comes with new delco alternator and bracket - trade for serp march pullies)
XE284 Camshaft and Lifters - 100 kms run time - $150
Dynomax Bullet muffler - has 3" over axle attached - $50
Harwood 4" Show series cowl hood - $450
240km/h Speedo - Good shape - $100
High Rise Z28 Spoiler - decent shape - $100
All prices are negotiable. PM or Email me. Pics can be available.
I'm thinking about going a different direction with the rims on the car. Maybe if I can sell off the GTA wheels it could help my situation. How much you figure? These rims are in pretty good shape. Some curb rash but nothing that can't be fixed by Carcones. No dents, no cracks etc. I painted them black last summer (gold starting to show) but they're still good. Come with WS6 caps.
The tires are Cooper Cobra 245/50/16 on the front and 255/50/16 on the rear but theres about 60% tread on the rears left. I might keep the tires so price would be made on rims with/without tires. Heres a few pics...
I figure I'll ask $500 obo. Rims are in good shape besides the fronts having minor curb rash. Rims look mint on the car!
SOLD.
Up for sale are a full set (2 front, 2 rear) of gold 5 spoke OEM 16" IROC-Z rims with Geostar 245/50R/16 tires. They also have 2 black center caps.
The tires have between 5/32 and 7/32 tread left on them. I also have another pair of Geostar tires, same size and unmounted that would be good for replacements on the rear rims.
For sale :
Year : 1988
Make : Pontiac
Model : Trans-Am GTA
Colour : Flame-Red Met.
Engine : 5.7L TPI
Transmission : THM700R4 4speed automatic
Rearend : 3.45 Posi 9bolt
Vehicle has 191,000km, runs and drives like new. Has 1997 Trans-Am leather seats front and back, black carpet inside. Has factory Digital Dash (in perfect working order). Transmission has ~20,000km on it, Corvette stall convertor, Corvette servo and govenor, Kevlar bands, Built @ GM dealer. Recently replaced rad hoses upper and lower.
Never seen winter, NO rust on body or underbody, floors/subframes are solid with no signs of rust!
Comes with custom build trunk subbox (with or without Kicker Comp C12 Sub/Jesnen Amp, can be discussed in price)
Engine is stock except for Accell High Output Coil, CAI and custom Dual exhaust (From Manifolds to under trans member is 2.25" Duals, into a 2-into-1 convertor then 2-3/4" pipe into Raven Crossflow muffler with stainless tips). Passed emission test with flying colours in April.
I have had Four of these generation of car, looking to go to a 4th gen Camaro or Trans-Am, bought this to help out a friend, and it is a beautiful driving/looking car, but I guess I am just bored.
Feel free to contact me with an offer, I would like 6200 OBO, but give me your offer.
Thanks for looking!
allright the time has come to sell all my parts from my 83, all parts have under 300kms on it unless otherwise stated..
almost 99% of the parts have reciepts.
pics shall be uploaded tomorrow and posts will be updated as sold.
heres what i got up for grabs.
80-85 SBC 350ci:
76cc Heads on it, Cast iron intake manifold, QJET Carb(needs to be set properly or replaced). This engine is supposed to be rated at 275hp by the "re-manufacturer" but apparently thats not the case but i do have a reciept for what i spent...
the block ALSO comes with L98 heads i picked up from merc305 (needs new valve seals).
Block is fire red and is on an engine cradle ready to be picked up.
asking $1200 OBO (reciepts show over 2000$)
T5 Trans out of 84 Camaro, w/ brand new centerforce clutch on it and a Flywheel to match up to the above block,
the bellhousing is there along with the stock shifter, the drive shaft, and the transmission cross-member. asking 800$ firm. (i have it listed on kijiji for 900$ (100$ TGO discount ))
CVR lightweight starter. Speaks for itself, mounts onto a SBC (not sure about BBC) asking 150$
Hooker headers 2055. they arent coated or anything and the ypipe has damage to it. $300
Stewart high flow waterpump: non serp setup (part number 23113, CW rotation cast aluminum finish) $150
Alternator: $50 SOLD
MSD Street-Fire HEI Distributor and MSD wires: 150$ (paid 230 +90) SOLD
High-flow 3" Cat: $50 or $350 for headers and cat!
Thats it i will update my posts and get pictures added at somepoint today,
i can be reached via PM or email both shall be answered ASAP..Thanks
My buddy is picking up an '87 Camaro. He needs a passenger side tail light (or a set), a passenger side t-top, and a windshield. He might need a passenger side window too, not sure. Anyone parting out a Camaro around here?
Yukon/Motive 3.70 gears, newer posi (2k), TA diff girdle, disc brakes with ebc pads, fresh rebuilt this year. Offer me up a price, don't know how much it's worth.
Also for sale, my 4" Harwood Cowl hood. Heres the kijiji link... Harwood 4" Cowl Hood
My buddy is picking up an '87 Camaro. He needs a passenger side tail light (or a set), a passenger side t-top, and a windshield. He might need a passenger side window too, not sure. Anyone parting out a Camaro around here?
I've got a base model 87 hardtop that's heading to the scrap yard in the next couple of weeks.
It's a total rust bucket however there are a few bits and pieces that are salvagable.
No interior.
No sheet metal except the hatch.
No windshield.
V6 w/ a 700R4.
Near Barrie, Ontario.
I have a 1991 305 TPI small block chevy from a 1991 Trans Am GTA. Has a bit of a knock but other than that ran great. Has new rings, redone heads about 8000kms ago. Comes with TPI setup, all serpentine accesories, headers, starter, pretty much everything except the wiring harness (I have it but I need it for my project, I do have the ECM available though).
Email me if you want more pics or info. This is a great deal considering it comes with pretty much everything.
Those of you that have read my thread will know I had problems with this one sticking and the fact I broke one throttle blade screw (see pic) and doesn't affect operation. Other than that it's in it's original condition and packaging. It was on my car for an hour. If you're going for looks this is a nice choice to dress up your engine. There are no plenum gasket, coolant housing gasket or machine screws for the AIC housing in the box. The throttle cable adapters are there for other applications. Installation instructions included.
Check the Summit site for proper application of this part (P/N 69704).
1987 GTA
White, light saddle cloth interior.
5.7 L 104 000 original KM's
4 speed auto. T-Tops
WS6 Suspension
Digital Dash-all lights work.
Safetied and no e-test required
Insurance is on it if your serious and want to test drive it.
Very nice shape
I've got a base model 87 hardtop that's heading to the scrap yard in the next couple of weeks.
It's a total rust bucket however there are a few bits and pieces that are salvagable.
No interior.
No sheet metal except the hatch.
No windshield.
V6 w/ a 700R4.
Near Barrie, Ontario.
Here a few pics of the hatch. It's not in very good shape.
Didn't mean to waste your time. I thought it was in much better condition than it is.
Due 2 an electrical fire, there was some small damage 2 the dash (drivers side). Needs windshield and drivers side glass. NOT beyond fixing, but I dont have the time or patience. EVERYTHING ELSE on the car is good. Body is GREAT. rest of interior is good. Car has and IROC hood, and 16'' ZQ8 wheels (From an S-10) Engine runs GREAT. ASKING $2000 OR best offer. Can take pics if u wish.
WTB...
camaro rear impact brace (the steel piece that bolts onto the frame) and energy absorber (rivited onto the impact brace). Colour not important, but as rust free as possible.
TIA
-Andrew
I just got a new parts car for the T5 thats in it as I think I will be going stick next year and a few other pieces like the GFX and Rims are really it. The rest is up for grabs. It has no motor and is a drum rear end. Heres some of the stuff out of it so far that i took out tonight. All parts are located in alliston and can be brought down but i only go up there on wednesday and sunday nights. Pics can be taken but you will have to go up to take them. Not looking for alot just want to recover some of the money I paid for it. Shoot me an offer on what you would want from it as the body will be scrapped in 2 weeks as I need my spot back for my car for winter storage.
Some of the stuff not in pictures are
--- RS flat hood in awsome shape $60
--- both doors are decent but not immacutale little rust on both $50
--- both fenders are decent each one has 1 small dent in them $20
--- Hatch is decent has no rust but has a few holes drilled from a wing that was on it for some reason $40
--- Steering column seems to be fine and i have 1 key for it $60
--- auto meter water gauge
--- B and M line lock handle $30
--- Holley 670 street avenger (needs rebuild) $200
--- rear grey carpet $25
--- another set of black rear seats as well $40
If you need something not listed let me know as I can see if i have it for you
Grey door panels $50 for the pair
complete dash. Has a few holes drilled in it from after market gauges $60
Rear seats Mint no holes or rips $50
Almost complete grey interior seat belts, sun visors, rear carpet included as well as the tiny pieces you would need as well if you want the whole interior. Only missing the door stills, door panels, headliner and sail panels. $150
Some racing seats. Driver side is mint passenger side the sides and bottom of the seat are a little ripped up. I think you can make it out in the pic $60 for the pair
Power hatch motor. Havnt tested it as the car has no power but looks to be in working order $40
The crazy wing i found in the back seat and looked as it was actually on the car at one point. If you have a ***** friend you know he will want this LOL $40
Wanted - 3rd gen spoiler mounted third brake light switch.
the spring loaded one that mounts underneath the rear hatch.....its missing on my car, just the wire is hanging there
Also wanted - 4th gen aluminum driveshaft and aftermarket 3rd gen strut tower brace, lower control arms, panhard bar.....if you have some lieing around doing nothing.haha email dee.scott@rogers.com
Selling off some left over parts from my 87 Formie. All parts in Ottawa, can ship at buyers expense. All prices are cdn dollars. More to come as i clean out my basement...
I have a basically new Spohn Crossmember for an LT1 T56 with a Driveshaft loop, as seen in my T56 Swap sticky. Its powder coated black, has 1 scratch, and a bit of primer overspray. Spohn sells this for $145 USD + shipping +UPS duty + cdn Tax. It cost me 210 to get to my door.
Asking $145 firm.
Selling my auto/6speed shift plate. You get the bare shift plate, with the ashtray lid and working spring. No lighter, ashtray, switches. The PRNDD21 has been replaced with a "FIREBIRD" emblem that illuminates like the other acetate. The shiftplate has an invisible crack, and is very clean. I have the PRNDD21 and some spare FIREBIRD acetates somewhere, but dont count on me finding them. If they turn up, they will be included. This was used in my T56 car, with no binding or hitting.
)) 
) 
