Home Register FAQ Members List Photo Gallery Garage Search Today's Posts Mark Forums Read Vendors



Go Back   Third Generation F-Body Message Boards > Tech Boards > TPI
Reload this Page China Wall oil sensor
Sign in using an external account
Register Forgot Password?

TPI Tuned Port Injection discussion and questions. LB9 and L98 tech, porting, tuning, and bolt-on aftermarket products.

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 11-20-2007, 01:30 PM   #1
Member
 
Cambridge205's Avatar
 
Join Date: Jun 2005
Location: Tucson, AZ
Posts: 217
Car: 89 GTA
Engine: L98 350
Transmission: Swapped to a T-5
Axle/Gears: 3.27

Classifieds Rating: (0)
China Wall oil sensor
I got an open oil passage in the back china wall and I forget if a sensor goes there or not. I already have an oil sensor above the oil filter its black with a 3-wire connector. I heard an oil sender or something goes on the china wall also but I don’t remember any sensor being there. Does any sensor go on the china wall for my car? If not where can I get a plug, to plug that hole? Because the machine shop left the china wall oil passage open and plugged the passage above the oil filter. Thanks.
Cambridge205 is offline vBGarage Page   Reply With Quote
Old 11-20-2007, 01:32 PM   #2
Moderator
 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Rio Oro de Santa Ana, San Jose, Costa Rica
Posts: 19,797
Car: 1984 Z28 Hardtop / 1988 IROC T-top
Engine: 383 Carb / 305 TPI
Transmission: 4L60 / T-5
Axle/Gears: 3.54 Dana 44 / 3.08 10 bolt

Classifieds Rating: (0)
Re: China Wall oil sensor
Just plug it with the pipe plug that you took out of the hole above the oil filter.
Apeiron is offline vBGarage Page   Reply With Quote
Old 11-20-2007, 01:41 PM   #3
Member
 
Cambridge205's Avatar
 
Join Date: Jun 2005
Location: Tucson, AZ
Posts: 217
Car: 89 GTA
Engine: L98 350
Transmission: Swapped to a T-5
Axle/Gears: 3.27

Classifieds Rating: (0)
Re: China Wall oil sensor
I think its a different size, and the machine shop super glued it in or something I had to drill it out a little with out drilling to the other side of the plug and use an easy out so that plug is ruined.
Cambridge205 is offline vBGarage Page   Reply With Quote
Old 11-20-2007, 02:04 PM   #4
Moderator
 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Rio Oro de Santa Ana, San Jose, Costa Rica
Posts: 19,797
Car: 1984 Z28 Hardtop / 1988 IROC T-top
Engine: 383 Carb / 305 TPI
Transmission: 4L60 / T-5
Axle/Gears: 3.54 Dana 44 / 3.08 10 bolt

Classifieds Rating: (0)
Re: China Wall oil sensor
It's the same size. They didn't glue it in, they used thread sealer on it as they should have.
Apeiron is offline vBGarage Page   Reply With Quote
Old 11-28-2007, 06:31 PM   #5
Member
 
Cambridge205's Avatar
 
Join Date: Jun 2005
Location: Tucson, AZ
Posts: 217
Car: 89 GTA
Engine: L98 350
Transmission: Swapped to a T-5
Axle/Gears: 3.27

Classifieds Rating: (0)
Re: China Wall oil sensor
I know they didnt super glue it in they just did a good job. Anyways how tight should the plug be? Becuase it keeps leaking alot of oil.
Cambridge205 is offline vBGarage Page   Reply With Quote
Old 11-28-2007, 06:46 PM   #6
Moderator
 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Rio Oro de Santa Ana, San Jose, Costa Rica
Posts: 19,797
Car: 1984 Z28 Hardtop / 1988 IROC T-top
Engine: 383 Carb / 305 TPI
Transmission: 4L60 / T-5
Axle/Gears: 3.54 Dana 44 / 3.08 10 bolt

Classifieds Rating: (0)
Re: China Wall oil sensor
Did you use thread sealer on it?
Apeiron is offline vBGarage Page   Reply With Quote
Old 11-28-2007, 06:46 PM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > TPI
Reload this Page China Wall oil sensor
« Wire that I do not where it goes | 350 build up »

Tags
china, engine, sealer, wall
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 

1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 03:00 AM.

Contact Us - ThirdGen.Org - Advertising - Privacy Policy - Terms of Use - Jobs - Top

Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.5.2
All content copyright © 1997 - 2012 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details