Search



Go Back   Third Generation F-Body Message Boards > Tech Boards > Transmissions and Drivetrain
Register Forgot Password?

Transmissions and Drivetrain Need help with your trans? Problems with your axle?
Sponsored by Hughes Performance
Click Here

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 12-13-2000, 10:58 AM   #1
Member
 
Join Date: Mar 2000
Location: Winnipeg,Manitoba,Canada
Posts: 250

Classifieds Rating: (0)
Send a message via ICQ to GOLD85
How strong are 26 spline axels

well how strong are they. i'm planing a 406 swap in the spring as well as swaping out the old one legger 3.42s for some 3.73 or 4.10. the 406 should be close to 450 foot punds of torque. the thing is i dont want to invest in a set of gears and a posi unit and then strip my axels. also, do IROCs and GTAs have 28 splin axels and to the all have posi. thank you for your help.

------------------
when the green flag drops the bull$hit stops

350,performer RPM intake ,650dp, 700r4, headers, 3inch exhast
GOLD85 is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 02:03 PM   #2
Member
 
Join Date: Jul 1999
Location: Aruba
Posts: 134

Classifieds Rating: (0)
As long as your changing the gears and posi, go for the newer 28-spline axles... That's what I did and the shop got them for me from a yard at $50 a pair, i'd say that's fairly cheap insurance(comparing to the money for the gears and posi)... and they'll hold up just fine.
Baz89RS is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 05:39 PM   #3
ede
TGO Supporter
 
Join Date: Aug 1999
Location: Jackson County
Posts: 14,811

Classifieds Rating: (0)
Send a message via ICQ to ede
i don't think the 26 are any weaker than 28's, it's just that the posi units for the 28 spline are much better. i agree buy the 28's and the posi to match.

------------------
ICON Motorsports
1st & 3rd
ede is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 08:15 PM   #4
Moderator
 
AlkyIROC's Avatar
 
Join Date: Jul 1999
Location: 51N 114W, 3500'
Posts: 15,465
Car: 87 IROC L98
Engine: 588 Alcohol BBC
Transmission: Powerglide
Axle/Gears: Ford 9"/31 spline spool/4.86

Classifieds Rating: (0)

You'd probably break the gears before you break an axle. It's easy to swap to 28 spline axles. Even better aftermarket 28 spline axles are only $125 US each. www.drivetraindirect.com has them. Part number KAC7-A7

If you don't dump a clutch at 4000 rpm or use a transbrake then even 26 spline axles should hold up. It's the shock load that breaks the axles. Putting power through a normal automatic tranny or slipping a clutch won't put that kind of shock load to the axles.

Many of the IROC and GTAs came with 9 bolt diffs. I think these are 27 or 28 splines. I never pulled my axles to see. Somewhere around 88 or 89, the 10 bolts went from 26 to 28 spline. 93 and up are 28 spline but the axles are longer.

------------------
Stephen's racing page

87 IROC-Z Pro ET Bracket Race Car
383 stroker (carbed) with double hump cast iron heads and pump gas
454 Big Block buildup now in progress for the 2001 racing season

Best results before the 383 blew up
Best ET on a time slip: 11.857 altitude corrected to 11.163
Best MPH on a time slip: 117.87 altitude corrected to 126.10
Best 60 foot: 1.662

Racing at 3500 feet elevation but most race days it's over 5000 feet density altitude!
Member of the Calgary Drag Racing Association

87 IROC bracket car, 91 454SS daily driver, 95 Homebuilt Harley

[This message has been edited by Stephen 87 IROC (edited December 13, 2000).]
AlkyIROC is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 09:09 PM   #5
Supreme Member
 
Join Date: Nov 1999
Location: NE
Posts: 2,860
Car: 82 camaro SC
Engine: 350
Transmission: 700r4

Classifieds Rating: (0)

The added 2 splines aren't going to give you any more strength, the axle breaks it's not going to be from the lack of 2 splines. Chances are you will tear up the gears before anything else. Get the gears you want, install a powertrax locker in your existing carrier, the thick rear diff cover with the bearing preload, weld the axle tubes to the housing, install all new bearings. How long it will last depends on how hard you run it and how much traction you get(along with lots of other variables.

------------------
82 camaro--original steering wheel, brake/gas pedals, seats--everything else modified
82camaro
82camaro is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 10:14 PM   #6
Senior Member
 
Join Date: Jun 2000
Location: Glenbeulah, WI
Posts: 551
Car: 1988 Firbird
Engine: 355
Transmission: T-56
Axle/Gears: 3.91

Classifieds Rating: (0)

28 spline axles are 18% stronger then the 26 spline axles. The spacing between the splines is the same so the two additional splines can only be addded by increasing the diameter of the axle. The additional increase in diameter (even though it seems small) adds 18% more strength.

------------------
1988 Formula 5L/5sp 3.45 gears, SLP cold air kit, MAS gutted, TPIS air foil, TPIS AFPR, MAC headers, Mac under drive pulleys, MAC cat back, Relocated MAT.
Best ET street tires 13.85
Best 60 FT street tires 1.930
Best MPH street tires 99.29
bjankuski is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 11:10 PM   #7
Senior Member
 
Join Date: Aug 1999
Location: previously OKINAWA JAPAN,georgia, now new england
Posts: 626
Car: 1989 IROC--1989 T/A
Engine: 5.7 TPI in both
Transmission: W/C T-5 in both
Axle/Gears: B/W 3.27 in both

Classifieds Rating: (3)

i spoke to a guy from RANDY's RING and GEAR, Concerning my rebuild up(see my other post) and he said the 26 spline would be good in to high 12's. So my opinion would be if you have the money and need a new carrier then upgrade, but save your money if you only need gears. This reply goes more to the folks that are looking to upgrade for the sake of doing it. Good Luck to all

------------------
'89 SHAGGY IROC
L98 7r4, all free stuff,T.E.S.,HOOKER CAT BACK,KYB,ACCEL8.8,JET fan sw. etc.
so much to do , so little money
irocnroll89 is offline vBGarage Page   Reply With Quote
Old 12-13-2000, 11:10 PM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > Transmissions and Drivetrain

Tags
26, 28, 383, axels, axles, spilne, spline, stroker, strong, weaker
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 04:23 AM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
All content copyright 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details