Cross threaded lug nuts
#1
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: UCIrvine or SFV, CA
Posts: 1,128
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1999 Pontiac Trans Am
Engine: LS1 - 346 ci
Transmission: 4L60E
Cross threaded lug nuts
One of the studs for the lug nuts was cross threaded. Do I have to replace all 5 or can I just replace one? It's the front right wheel. How hard is this to do?
Thanx
Thanx
#2
Supreme Member
Join Date: Jan 2001
Location: ****SoCal, USA****
Posts: 7,604
Likes: 0
Received 0 Likes
on
0 Posts
Two choices
DON'T BOTHER TO DEAL WITH IT
or
Remove the rotor & have one pressed out & pressed in
At SAME TIME redo all five!
It's just as cheap as doing one!
PS on mine?
One stud broke.
I need to install all five at one.
I've already purchased five studs.
Awaiting the time to do it.
Right now I just drive using four, as it's ok.
DON'T BOTHER TO DEAL WITH IT
or
Remove the rotor & have one pressed out & pressed in
At SAME TIME redo all five!
It's just as cheap as doing one!
PS on mine?
One stud broke.
I need to install all five at one.
I've already purchased five studs.
Awaiting the time to do it.
Right now I just drive using four, as it's ok.
#3
Banned
Join Date: Feb 2003
Location: Mostly in water off So. Cal
Posts: 1,455
Likes: 0
Received 1 Like
on
1 Post
Car: '87 Chev
Engine: 60*V6
Transmission: DY T700
Here's one of my suspension board links that might be of interest to you.
https://www.thirdgen.org/techbb2/sho...hreadid=156235
https://www.thirdgen.org/techbb2/sho...hreadid=156235
#4
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: UCIrvine or SFV, CA
Posts: 1,128
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1999 Pontiac Trans Am
Engine: LS1 - 346 ci
Transmission: 4L60E
Thanks for the link AGood2.8. How long does it take from start to finish? It's pull the rotor, and then hammer it out with something like a 16 oz hammer? Might as well find new rotors while I'm at it. You think chrome lug nuts would look good?
#5
Banned
Join Date: Feb 2003
Location: Mostly in water off So. Cal
Posts: 1,455
Likes: 0
Received 1 Like
on
1 Post
Car: '87 Chev
Engine: 60*V6
Transmission: DY T700
Originally posted by 89V6FBIRD
Thanks for the link AGood2.8. How long does it take from start to finish? It's pull the rotor, and then hammer it out with something like a 16 oz hammer? Might as well find new rotors while I'm at it. You think chrome lug nuts would look good?
Thanks for the link AGood2.8. How long does it take from start to finish? It's pull the rotor, and then hammer it out with something like a 16 oz hammer? Might as well find new rotors while I'm at it. You think chrome lug nuts would look good?
16oz. hammer is fine /i used a 20 oz. with ease.
Wheel stud replacements on all four corners of my car took me about 2-3 hours- cleaning things and replacing front bearings and such. I am fully air tool equipped though. (Always use a new cotterpin on the front spindle jamnut!, My father reused one years ago on the rear axle of his '63 356 bathtub Porsche and lost the LR hub assembly on the Culver Frwy here in L.A.- Talk about an E-ticket ride. He spun the car to the left and came out of it with the car barely damaged at all- Pops is a heck of a driver in his ownright.)
#6
Supreme Member
Thread Starter
Join Date: Dec 2000
Location: UCIrvine or SFV, CA
Posts: 1,128
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1999 Pontiac Trans Am
Engine: LS1 - 346 ci
Transmission: 4L60E
I'm finally going to have time to do this tomorrow. Basically pull the bearing & rotor. What do I use to knock it out w/ the hammer? A chisel? or the hammer alone? Then once I get it out, I slide the new one in place, use the new lug nut to seat it right? Repack, then I'm done?
Prolly start cleanin out the project car tomorrow too!!! :lala:
Prolly start cleanin out the project car tomorrow too!!! :lala:
Trending Topics
#8
Supreme Member
Join Date: Mar 2000
Location: Central NJ, USA
Posts: 13,414
Likes: 0
Received 6 Likes
on
6 Posts
Car: 1986 Firebird
Engine: 2.8 V6
Transmission: 700R4
You might want to spin an old lug nut onto the top of the damaged stud; it'll give you something "bigger" to aim for with the hammer.
Use an old lugnut (or one you bought but don't plan on using for the car) to pull the new stud on. When I changed a snapped lugnut on my junkyard rear axle, I put a washer between the lugnut and the axle hub. When the new stud was in, I put the lugnut I used onto the snapped stud, and threw it in the toolbox.
Use an old lugnut (or one you bought but don't plan on using for the car) to pull the new stud on. When I changed a snapped lugnut on my junkyard rear axle, I put a washer between the lugnut and the axle hub. When the new stud was in, I put the lugnut I used onto the snapped stud, and threw it in the toolbox.
Thread
Thread Starter
Forum
Replies
Last Post
drptop70ss
Engine/Drivetrain/Suspension Wanted
3
10-04-2015 09:44 PM
84 TA NV
Firebirds for Sale
1
09-06-2015 08:02 PM