TPI and SBC parts for sale
#1
Member
Thread Starter
iTrader: (2)
Join Date: Nov 2004
Location: Innisfil, ON ,Canada
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
Engine: 360 .060 over TPI
Transmission: T-5
TPI and SBC parts for sale
1 set of 14101081 305 heads- stock vlaves, aftermarket springs, guideplates and screw in studs. less than 4 hours on rebuild heads. These are 1 of the 2 SCCA approved GM heads for American Sedan.
$250/OBO
Complete MAF TPI setup from 1988 IROC Ex players A4U/1LE car. CPU, TB, manifolds, distributor wiring harness, 24 lb Accell injectors, JET adhustable fuel pressure regulator. includes 3 MAF sensors+++
$400/OBO
ZZ4 camshaft hydraulic roller new in box, GM take out would work GREAT with a TPI- $175
New in box Speed pro Hypereutectic 350 dished pistons H423NCP 4.060 over full set of 8. coated skirts with rings and pins .- $180
1993 LT1 cam- maybe aftermarket has "1??2 244 CPC BC" after the fuel pump lobe. appears to be a steel and heat treated $40
3/31/04- put it in a blcok and put my dial gauge on a lifter. .288 lobe lift = .288 x1.52=.438 valve lift. mild street cam
1991 stock 350 Z28 hyd roller camaro cam # on end of cam 109356 $40
balanced Rotating assembly-
350 cast crank .010/.010 turned, 1 piece rear main seal.
set of 8 resized connecting rods with ARP bolts, less than 4 hours on rods and crank. Stock 1988 IROC Flywheel for 1 piece rear mian seal and damper. This assemlby was all ballanced together. Had +.060 forged speed pro flat top pistons on it. get new pistons and don't need to rebalance.
NEW in box Rod bearings included.
$300/obo.
used, less than 4 hours-High volume oil pump with welded in stock pickup sealed power #55HV $40
Have matching oil pan with welded in bung for oil temp sender and front timing cover $40
BEST offer or trade for sbc performance parts, distributor headers, 9 bolt rear end 3.73 gears? or T-5/Richmond gear T-10 stuff. etc.
thanks
Steve
Barrie, Ontario Area
--------------------------------------------------------------------------------
$250/OBO
Complete MAF TPI setup from 1988 IROC Ex players A4U/1LE car. CPU, TB, manifolds, distributor wiring harness, 24 lb Accell injectors, JET adhustable fuel pressure regulator. includes 3 MAF sensors+++
$400/OBO
ZZ4 camshaft hydraulic roller new in box, GM take out would work GREAT with a TPI- $175
New in box Speed pro Hypereutectic 350 dished pistons H423NCP 4.060 over full set of 8. coated skirts with rings and pins .- $180
1993 LT1 cam- maybe aftermarket has "1??2 244 CPC BC" after the fuel pump lobe. appears to be a steel and heat treated $40
3/31/04- put it in a blcok and put my dial gauge on a lifter. .288 lobe lift = .288 x1.52=.438 valve lift. mild street cam
1991 stock 350 Z28 hyd roller camaro cam # on end of cam 109356 $40
balanced Rotating assembly-
350 cast crank .010/.010 turned, 1 piece rear main seal.
set of 8 resized connecting rods with ARP bolts, less than 4 hours on rods and crank. Stock 1988 IROC Flywheel for 1 piece rear mian seal and damper. This assemlby was all ballanced together. Had +.060 forged speed pro flat top pistons on it. get new pistons and don't need to rebalance.
NEW in box Rod bearings included.
$300/obo.
used, less than 4 hours-High volume oil pump with welded in stock pickup sealed power #55HV $40
Have matching oil pan with welded in bung for oil temp sender and front timing cover $40
BEST offer or trade for sbc performance parts, distributor headers, 9 bolt rear end 3.73 gears? or T-5/Richmond gear T-10 stuff. etc.
thanks
Steve
Barrie, Ontario Area
--------------------------------------------------------------------------------
Last edited by player 88; 04-02-2006 at 02:48 PM.
#2
Supreme Member
iTrader: (4)
Join Date: Apr 2006
Location: Windsor Ontario
Posts: 1,128
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1987 Z28
Engine: 2005 5.3L, LS6 Cam
Transmission: T56
Axle/Gears: DTS 9" 3.50 TrueTrac
hey Im probaly picking up a 91 TBI RS so I may pick up the TPI setup from ya if u still have it in a few months....I need to save some cash then start modding it...its a project car.
You have any pics etc?
Send to jamesrichard727@hotmail.com
thanks Jay
You have any pics etc?
Send to jamesrichard727@hotmail.com
thanks Jay
Thread
Thread Starter
Forum
Replies
Last Post
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
08-12-2015 03:41 PM