WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
#1
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Jul 2001
Location: San Jose, CA
Posts: 1,828
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2002 Z28
Engine: LS1
Transmission: 4L60E
Axle/Gears: 3.23
WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
Have: 24mm 1LE Rear Sway Bar w/ poly bushings and non-stock brackets.
Need: 21-22mm Rear Sway Bar w/ poly or low mileage rubber bushings.
Don't Need: 18mm, 19mm, 20mm, 23mm, 24mm or 25mm or any front bars
I would also like to see some pictures with measurements verifying the size, I can send pictures if requested (on wednesday)
David
Need: 21-22mm Rear Sway Bar w/ poly or low mileage rubber bushings.
Don't Need: 18mm, 19mm, 20mm, 23mm, 24mm or 25mm or any front bars
I would also like to see some pictures with measurements verifying the size, I can send pictures if requested (on wednesday)
David
#2
Supreme Member
iTrader: (2)
Join Date: Mar 2005
Location: East Tennesse
Posts: 2,820
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1991 RS Camaro
Engine: L03 (want LS1)
Transmission: 700R-4 (and T56)
Axle/Gears: 4th Gen 3.23 posi
Re: WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
You and I are in the same boat...I hope it's not 6 months before I find me a bar.
#4
Supreme Member
iTrader: (2)
Join Date: Mar 2005
Location: East Tennesse
Posts: 2,820
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1991 RS Camaro
Engine: L03 (want LS1)
Transmission: 700R-4 (and T56)
Axle/Gears: 4th Gen 3.23 posi
Re: WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
The 24 and 25mm rear bars are usually too much sway bar for the cars unless you lowered the pan hard bar. They cause the car to over-steer under throttle exiting turns. At least in my case. Sometimes, bigger isn't always better.
#5
Member
Join Date: Jul 2006
Location: Kent, WA
Posts: 365
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 z28
Engine: boat anchor 305 (ex CFI)
Transmission: 700r4
Axle/Gears: 3.23 10 bolt
Re: WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
I have either a 22 or 23 behind my early Z. I will measure and let you know.
Cheers!
Cheers!
#6
Supreme Member
iTrader: (2)
Join Date: Dec 2005
Location: Beaufort South Carolina
Posts: 1,739
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1983 Camaro Z/28
Engine: LU5 305 CFI
Transmission: 700R4
Axle/Gears: J65/G80/G92-3.23
Re: WTT: My 24mm Sway Bar for your 21-22mm Sway Bar
Klause if it's the rear bar off your '83 Z28,and if it was the original one - best to mic it,then it should be a 21mm that they are looking for.
Thread
Thread Starter
Forum
Replies
Last Post
darwinprice
Organized Drag Racing and Autocross
17
10-11-2015 11:51 PM