Differences and Pics of Both Types of Overhead Consoles
04-13-2002, 04:31 PM
#1
Pics of Both Types of Overhead Consoles
Overhead Console: RPO DK6 (84-87).
I've noted that some people are unaware of the differences between the two. By the way, the accessories--sun glass pouch, flash light (though physically the same, there are two versions, one with "Camaro" lettering, the other with "Firebird") map light bezel, map light, felt piece(s), and bulb are all the same. Check the following link for pics and info about that:
https://www.thirdgen.org/techbb2/sho...03#post2138603
First, is the general shape. The coupe version is not only much more curved to fit the roofline but also has a reinforcement piece that slips under the headliner. Also, note that the area just in front of the dome light (the area that houses the flashlight) is wider.
I've noted that some people are unaware of the differences between the two. By the way, the accessories--sun glass pouch, flash light (though physically the same, there are two versions, one with "Camaro" lettering, the other with "Firebird") map light bezel, map light, felt piece(s), and bulb are all the same. Check the following link for pics and info about that:
https://www.thirdgen.org/techbb2/sho...03#post2138603
First, is the general shape. The coupe version is not only much more curved to fit the roofline but also has a reinforcement piece that slips under the headliner. Also, note that the area just in front of the dome light (the area that houses the flashlight) is wider.
Last edited by JamesC; 05-03-2012 at 03:15 PM.
04-13-2002, 04:34 PM
#2
A second difference is how the console mounts. In the pic, the t-top version is on top.
The mounting 'slots' are not only in different positions but also slide onto the mounting studs from an opposite direction.
The mounting 'slots' are not only in different positions but also slide onto the mounting studs from an opposite direction.
Last edited by JamesC; 07-24-2004 at 07:26 AM.
04-13-2002, 06:48 PM
#4
Banned
Join Date: Nov 2001
Location: rochester ny
Posts: 212
Likes: 0
Received 0 Likes
on
0 Posts
ive been wanting to get one of those for my t tops car.whats involved in installing one of those?what kid of hardware,if any is needed?and are they too hard to wire up?thanks!
04-13-2002, 07:01 PM
#5
Check the tech articles for installation, which is straightforward (In my 85 IROC, for example, the holes were pre-drilled for the mounting hardware). I have several consoles, complete and otherwise, that I'll list in the classifieds soon.
JamesC
JamesC
Last edited by JamesC; 02-20-2005 at 07:00 AM.
04-14-2002, 12:46 AM
#6
Supreme Member
iTrader: (1)
Join Date: Mar 2001
Location: Cherry Hill, NJ
Posts: 2,181
Likes: 0
Received 1 Like
on
1 Post
Car: 92 Trans Am 'Vert
Engine: 305 TPI
Transmission: 5 Speed
So James, which one is which? Is the curved one for hard top or t-tops? I have 3 of em, and theyre all straight ones, and I havent tried to put it on my GTA yet.
04-14-2002, 07:02 AM
#7
The curved version fits the coupe/hardtop. I've read on this board that some guys have used the t-top version on a coupe, but given the differences, I would think that conversion would be very difficult.
JamesC
JamesC
Last edited by JamesC; 07-24-2004 at 07:27 AM.
Trending Topics
04-15-2002, 06:27 AM
#9
Please note that in the first pic, there are no sun glass pouches. This area would be an excellent for mounting switches and/or switch boxes of varying sorts. Blocking off the hole for the flash light would provide yet another option.
JamesC
JamesC
Last edited by JamesC; 07-24-2004 at 07:27 AM.
04-15-2002, 05:50 PM
#10
Supreme Member
iTrader: (5)
Join Date: Jan 2001
Location: Evansville,IN,USA
Posts: 2,025
Likes: 0
Received 1 Like
on
1 Post
Car: 89' T/A, 00' Firehawk
Engine: 406 Roller
Transmission: TH700R4 w/2800 stall
Axle/Gears: 3.23 Posi
i am looking for the light and the retaining ring that goes in the front of the counsle. anyone have one or know where to get one? thanks.
04-18-2002, 06:40 AM
#11
In answer to a couple of questions: The mounting hardware consists of four mounting studs, two screws (dome light), and one screw for ground. On the coupe version, the reinforcement piece goes in foam side up. The console can be mounted without removing the headliner. I made a simple cardboard cutout (put the console on the cardboard and draw around it, marking where all the holes should be), then used the two dome light screws as positioning guides. When you cut the headliner cloth, cut X's so that the material can be tucked under the headliner. Cut a little at a time and you can't really go wrong. Mine below. Also, check out these pics and write-up from noahTHEpurdy, which puts the above in better perspective:
https://www.thirdgen.org/forums/inte...d-console.html
JamesC
https://www.thirdgen.org/forums/inte...d-console.html
JamesC
Last edited by JamesC; 11-03-2006 at 07:05 AM.
04-18-2002, 07:18 AM
#12
Member
Join Date: May 2001
Location: Staten Island, New York, USA
Posts: 317
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Iroc Z "Classic Roc"
Engine: 5.7 350
Transmission: Auto
All of that posting and nobody mentioned the Pacman going on in the background?! 
:lala: Sorry dude, had to do it! 
:lala: Sorry dude, had to do it!
04-18-2002, 07:27 AM
#13
Supreme Member
Join Date: Jan 2002
Location: Here and There, Kansas
Posts: 1,175
Likes: 0
Received 1 Like
on
1 Post
Car: 89 Camaro RS
Engine: 2.8L V-6
Transmission: T-5
Hey, I would like to put one of those in my 89 RS. Would I have drill holes or are they already there for me, just have to get the console and cut the headliner? I got the domelight and thats it
04-18-2002, 07:38 AM
#14
USA-1, PacMan rules (and you know it!).
Disturb, my IROC had the holes pre-drilled, so it should be a simple matter of finding an appropriate console, cutting the headliner, splicing a bit of wiring, and mounting. I'm unsure that I read you right, but the stock dome light is removed and replaced with the overhead, which contains a dome light.
JamesC
Disturb, my IROC had the holes pre-drilled, so it should be a simple matter of finding an appropriate console, cutting the headliner, splicing a bit of wiring, and mounting. I'm unsure that I read you right, but the stock dome light is removed and replaced with the overhead, which contains a dome light.
JamesC
Last edited by JamesC; 07-24-2004 at 07:28 AM.
04-18-2002, 07:43 AM
#15
Supreme Member
Join Date: Jan 2002
Location: Here and There, Kansas
Posts: 1,175
Likes: 0
Received 1 Like
on
1 Post
Car: 89 Camaro RS
Engine: 2.8L V-6
Transmission: T-5
Thanx for the info JamesC. How much would one of those cost new from a GM dealer? I'm not really fond of putting stuff out of junkyards in my car unless I'm POSITIVE that they are in excellent condition.
04-18-2002, 10:20 AM
#17
Member
Join Date: Jun 2001
Location: Missouri
Posts: 319
Likes: 0
Received 0 Likes
on
0 Posts
Its sooo easy! there are four little clips. and 2 screws that are in the Light cover... then the power clips right up... i could take mine down, run a mile, and have it back up in 6.5mins! theres nothing to it!
04-24-2002, 04:25 PM
#19
Mounting hardware (the wiring can be seen above) and flash light. The bulb for the flash light can be purchased at Radio Shack: part # 272-1124, packaged as # 243 (222) Flashlight Lamp.
JamesC
JamesC
Last edited by JamesC; 10-20-2010 at 06:20 AM.
05-17-2002, 12:56 PM
#21
05-17-2002, 02:47 PM
#22
Supreme Member
Join Date: Jan 2002
Location: Here and There, Kansas
Posts: 1,175
Likes: 0
Received 1 Like
on
1 Post
Car: 89 Camaro RS
Engine: 2.8L V-6
Transmission: T-5
JamesC,
Do you still have any for a non T-top car? I will be making a good amount of money this summer (bout $3500) and would like to buy one from you if you have one in good condition, black, and would like to have the camaro flashlight if possible in it. thanx for any info.
Do you still have any for a non T-top car? I will be making a good amount of money this summer (bout $3500
) and would like to buy one from you if you have one in good condition, black, and would like to have the camaro flashlight if possible in it. thanx for any info.
02-16-2004, 12:02 AM
#25
Whoa, old thread. Does any one know where I can find these mounting bolts? The 4 silver ones that are used to hold the biggest part of the console in place?!?!? I bought a console, but it did not come with the hardware and I am now out of luck.Thanks fellas
Will
Will
02-16-2004, 12:42 AM
#26
Member
Join Date: Jun 2003
Location: British Columbia,Canada
Posts: 327
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Firebird
Engine: L03
Transmission: 700r4
Axle/Gears: ?
anyone in canada want to trade a hardtop console for a t-top console(my hardtop console, looking for a t-top console) it doesnt have the camaro flashlight, but u may keep yours if u have one...PM me if intersted
02-18-2004, 03:02 PM
#28
Junior Member
Join Date: Feb 2004
Location: Central Florida
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89/'87/'82 "TransMaro L-81"
Engine: '82 Corvette L-81 (carbed)
Transmission: 700R4
Originally posted by USA-1
All of that posting and nobody mentioned the Pacman going on in the background?! :lala: Sorry dude, had to do it!
All of that posting and nobody mentioned the Pacman going on in the background?!
:lala: Sorry dude, had to do it! Pac Man rocks!:rockon:
02-19-2004, 05:35 PM
#29
Senior Member
Join Date: Feb 2002
Location: Lehigh Valley, PA
Posts: 830
Likes: 0
Received 0 Likes
on
0 Posts
Car: 00 T/A Firehawk
Engine: 346ci LS1
Transmission: MN6
Axle/Gears: 3.42 LSD
Very informative (and old) post! I'd love to get my hands on one of these, but they seem to be hard to find!
03-12-2004, 10:53 AM
#31
If age has caused the yellowing, there's not much to be done. If caused by smoking, the plastic can be freshened up with soap and water or a product called Soft Scrub (used on Convert rear windows).
JamesC
JamesC
Last edited by JamesC; 07-24-2004 at 07:30 AM.
07-23-2004, 01:55 PM
#32
Member
Join Date: Aug 2003
Location: Nogales Sonora, Mexico
Posts: 131
Likes: 0
Received 0 Likes
on
0 Posts
Car: Firebird 89' and Formula 87
Engine: 2.8 l and 350 v8
Transmission: 2.8 Manual 5 speed and 5.7 manual 5 speed
I got one of those consoles for my ttop trans am , but the one that i got is for a coupe car is it posible to install a cope one into a t top car?would any body be interested in trading a cope console for a t top one?
02-23-2005, 09:17 PM
#33
Supreme Member
Join Date: Sep 2002
Location: So Cal (SD)
Posts: 1,467
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 firebird now
Engine: 305
Transmission: 5 speed
Originally posted by LilJayV10
i am looking for the light and the retaining ring that goes in the front of the counsle. anyone have one or know where to get one? thanks.
i am looking for the light and the retaining ring that goes in the front of the counsle. anyone have one or know where to get one? thanks.
05-26-2005, 12:42 AM
#34
Supreme Member
iTrader: (1)
Join Date: Aug 2004
Location: colorado
Posts: 2,122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Trans/am convertible
Engine: 305 TPI
Transmission: 700r4
Axle/Gears: 2.73 drum WS6
Bringing this one up from the dead!
I installed a hard top camaro one on the T-top firebird. All you need to do is drill a hole at the front of the console (the one closest to the rear view mirror) and with a little persuasion (must be gentle yet firm) I screwed it with a self tapping screw. Now it fits perfectly.
I thought I post this with pictures so you can see that it is possible to mount a hard top one into a T-top car.
I installed a hard top camaro one on the T-top firebird. All you need to do is drill a hole at the front of the console (the one closest to the rear view mirror) and with a little persuasion (must be gentle yet firm) I screwed it with a self tapping screw. Now it fits perfectly.
I thought I post this with pictures so you can see that it is possible to mount a hard top one into a T-top car.
02-07-2006, 09:30 PM
#35
Junior Member
iTrader: (4)
Join Date: Jul 2005
Location: Minnesota
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1972 GMC
Engine: 355
Transmission: 700r4
Axle/Gears: 4:10
Just what I have been looking for, have a lead on an overhead in excellent condition, but needed to know install and difference to make sure I get a ttop console.
Thanks for thee info
JC
Thanks for thee info
JC
08-06-2011, 10:32 PM
#36
Supreme Member
Join Date: Jan 2011
Location: Lynden WA
Posts: 1,929
Likes: 0
Received 3 Likes
on
3 Posts
Car: 84 Trans Am, 84 Fiero, 86 944
Engine: 5.0, 2.5, 2.5
Transmission: 5spd
Re: Differences and Pics of Both Types of Overhead Consoles
sorry way old thread but, do the ones from hawks just go right in, i mean do they come with all the mounting hardware? and i dont have to worry about the headliner, its gone lol
12-19-2017, 05:10 PM
#38
Junior Member
Join Date: Oct 2017
Location: Stanwood, MI
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Camaro Iroc Z28
Engine: 305 5.0 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: Differences and Pics of Both Types of Overhead Consoles
I know these are old, but I thought of removing the old trip meter dials in the roof console and placing my switches there.
Thread
Thread Starter
Forum
Replies
Last Post
colton_carlson
Firebirds for Sale
7
03-08-2019 12:21 PM
