![]() |
4th gen seats Do 4th gen seats bolt right into a third gen. Ive heard you need to drill holes to make them work. |
Direct 100% no-mod bolt-in perfect fit. :nod: |
d@am right! |
d@am right! |
yup, go for it |
Really, they bolt right in!!!! Cool. :D |
(8) 14mm fasteners for the fronts and (4) for the rears thats all youi have to remove & replace.:) :) |
|
does anyone have any pictures of it? -fly |
i don't think anyone has done it yet:D biker |
1 Attachment(s) Lookie Lookie!!! I got mine to work after 3 days of modification! I was about to give up. :D :D :D :D :D 100% bolt in unless you have a split fold rear seat then you need to loose the little bar thingy on the drive shaft tunnel....right? |
1 Attachment(s) What modifications??? There is none on 4Th Gen seat install. Did mine in less then 2 hrs and that included cleaning the carpet. |
Originally posted by Z28DJP1987 What modifications??? There is none on 4Th Gen seat install. Did mine in less then 2 hrs and that included cleaning the carpet. |
1 Attachment(s) :D |
1 Attachment(s) Here's mine, came out of a '00 Z28. |
Billsfirebird, what 4th gen did those come out of? If i can't get aftermarket those look like a nice set. |
Just to confirm. I do beilve that they MIGHT fit. I can neither confirm, nor deny that. But I have it on good athority that they will fit. I also have it on good athority that they wont fit. I guess you will have it work, or it wont work... |
DUDE MAN its so Hard to put 4th Gen Seats in you have to weld and cut in like 50 places its so not worth it man than you have to drop the gas take and Pull the Trans its a big pain in the but... i think im gona start being the new Search Nazi Try the Search KEY next time |
Originally posted by 86IROCNJ Billsfirebird, what 4th gen did those come out of? If i can't get aftermarket those look like a nice set. |
Originally posted by billsfirebird Came right out of a 93 Camaro. :D |
Originally posted by Saywhut How'd 'ya get 'em to fit in your car? Duct tape and bubble gum. (in case it was a serious question...just used all the existing hardware. no mods) :D |
Duct tape and bubble gum. LOL |
So wait a second........I can actually remove the seats from a 4th Gen and place them directly in a 3rd Gen......???? But the body styles are different.......??? I wouldn't recommend doing this swap, you need to remove the engine for saftey precautions so it can be a long drawn out process......;)......plus you need a engine lift....:cool: |
Originally posted by FLYNLOW92rs So wait a second........I can actually remove the seats from a 4th Gen and place them directly in a 3rd Gen......???? But the body styles are different.......??? I wouldn't recommend doing this swap, you need to remove the engine for saftey precautions so it can be a long drawn out process......;)......plus you need a engine lift....:cool: how about the rear hatch, to get the rear seats in?? lol :D |
I heard you need one of those chassis roller thingies. Also, I heard that the swap isn't possible with hardtops, need t-tops or a convertible to get the seats in. |
seats? what are seats? |
Double Post :lala: :lala: :lala: |
So what do you do after you drop the tank. Cant get mine to work, what kind of bubble gum did you use... Damnit anybody wanna buy a set of 4th gen seats. Thanks for the help guys. |
:sillylol: You guys are rotten :nod: :D |
I thought it went something like you had to weld in subframe connectors and a main hoop from a six point roll bar and then drill and tap the upper left side of the passenger side seat whith the car in park. But I could have heard wrong. I once had a friend that did that swap and he had to get his front end aligned. Good luck on the this very challenging swap, it will be a long hard road but worth it. |
You guys are such jerks. The guy asked a simple question....it only required a simple answer. YES, they do bolt right in. Of course, you'll have to bolt the rear seat in backwards...kinda like the old caprice station wagons....or it won't fit. If you want your passengers to face forward, then it's a different story all together. :lala: |
Originally posted by TheLG4Whore I thought it went something like you had to weld in subframe connectors and a main hoop from a six point roll bar and then drill and tap the upper left side of the passenger side seat whith the car in park. |
I'm SOOOOOO confused!:doh: |
seats YOUR ALL WRONG !!!!! You have to take the carpet out first, then install the seats, then put the carpet back in ! If you don't then the heater won't work.:doh: |
i know that the seats are a direct fit but the door panles aren't right |
Originally posted by mess21 i know that the seats are a direct fit but the door panles aren't right |
any way to make them fit probally not worth it though huh |
Wait a minute, I had to cut the roof off of mine to get the back seat in because it wouldn't fit through the doors or the hatch! I guess next time ill know just to cut the car in half, it'll save alot of trouble!:D :D :D :D :D |
i heard that if you have a 305tbi the seats will not work since the engine is such a torque monster it will actually rip the seats off the of the floor:p |
well actually I've learned from my experience that you should install a wheelie bar and a 4 link rear suspension cause the 4th gen seats completely mess up your weight distribution when running under 15,000+ feet altitude. I could be wrong but I had a near death experiance when I floored it in 5th gear after my 4th gen seat swap, the car almost completely flipped over and so on. and for a safety precaution you might wanna consider a pre-'75 dual points distributor setup but that's only for safety purposes. I've also found that oil pan windage trays help when running the seat swap without the proper suspension setup. Hope I was helpful. peace |
:sillylol: :sillylol: :sillylol: :sillylol: :sillylol: Thanx I needed that, started to turn into a bad day. And as far as the seats go, the modifactions, and yes there was at least one, was the power, if the seats are powered, be sure and get the harness. I think it's worth it, I love mine. |
Huh I have Power Seats..Can i just splice the wires? Or do i gotta Rip the doors, hatch, hood,groundeffects off? The hood has a light that takes to much power and your car dies with it on there. Doors need to come off for the front seats to come out and put the 4th gen in. Hatch comes off for the back seats. Groundeffect got to come off or you will scratch them. |
Hey, does anybody know if 89 IROC seats will fit in a 89 RS? What would I have to do to make 'em fit? If they were power IROC seats, and I wanted to put 'em in a RS that had power seats, would I have to swap the IROC harness also? I was thinkin' I could just wire them into the cigarette lighter, then all I'd have to do would be hold the liter in with one hand and adjust the seats with the other. Maybe. |
YES, they do bolt right in. j/k:p :p |
I dont remeber this post. But I seem to have replied to it earlier. andewayz I am the Seach Nazi, so do a Search, and all you wishes will come true.... :p What was the question again??? |
I like pizza!!!!! :lala: :lala: :lala: |
Im gonna laugh when some innocent 16 yr old hacks there car in half with ye ole' chainsaw :lala: :lala: :lala: |
My personal opinion is that all you "so called comics" have had your fun with this question, so put it to rest. The real impression I get is you are AH's and have no knowledge of the subject or did this conversion. |
I do have knowledge on this topic! Why? because I actually searched and looked at other 4th-gen seat swap threads that other people have posted. Now, see how much grief, time, and frustration that silly little mistake of the guy not searching, or looking for another thread on 4th-gen seat swap caused? Now, I know I replied with a stupid post, but we all joke around right? I think this thread should be closed! |
That would be the smartest thing said about this Post lately. |
All times are GMT -5. The time now is 06:52 PM. |
© 2024 MH Sub I, LLC dba Internet Brands