Bypassing VSS buffer box
 

I have a question on the VSS buffer box for a LS swap. I know that the buffer box (yellow box behind the passenger side dash panel) is not needed and needs to be bypassed. I do not know how, which wires need to be connected.

I believe this is what I have:
https://cimg7.ibsrv.net/gimg/www.thi...9d16b85911.jpg

I seem to be unable to start the car without grounding the ground wire in that circuit, and I currently have no Speedometer or Tach working. Do these wires need a jumper on them?

It also looks like I could use the pnk/blk wire for a boost wire on the speedometer if need be.

Thanks,

Re: Bypassing VSS buffer box
 

I haven't actually done this so you might take my advice with caution, but I also have a 1989 Firebird so I had to research it. My understanding is that you already have an electronic speedo that can understand the speed output of the LS1 PCM. You don't even need the buffer box any more. The goal is to get the speed signal from "R50" of the LS1 PCM to your speedometer input, which is "pin C" of the connector at VSS buffer box.

* You can do it directly

OR

* You can tie LS1 PCM "R50" to the C207 connector pin K, and then jump pins C and F at the connector for the VSS buffer box. Most people do it this way because they have other connections at C207 anyway and it is a more tidy layout.

Re: Bypassing VSS buffer box
 

That's probably what I need to do. I forgot the box was removed at some point, and the connector was stuffed behind the dash. I reached back there looking for loose wires and pulled that connector out going "well that's probably why it doesn't work!

Re: Bypassing VSS buffer box
 

I know on the LT1 (looks like the same on LS1) the VSS goes directly into the ECM and there is an output for the speedometer. No box required. You only need a box (SGI-5) when you're using the wrong VSS signal.. IE a T5 where the ECM wants the 4L60E/T56, and only because the VSS generated is completely different than what the computer expects. If you're using cruise then there's an output for that too.
As for the ground, there is a wire on that side if memory serves that you ground to kinda bypass the VATS.. I'm running MegaSquirt so I grounded it, but I think on the LT1 (likely same on LS1) there is actually an input for it. So that may be why it won't start without grounding it. Assuming when you say it won't start, you mean no crank and even the relays aren't picking up.

Re: Bypassing VSS buffer box
 

You can bypass PASSkey (what people call VATS) one of three ways.

1. Keep the PASSkey module and install a resistor, that matches the key, across the two key switch wires located under the steering column. The PASSkey will always see the correct resistance and let the engine start.

2. Remove the PASSkey module and jump terminals A3 and B1 at the PASSkey connector. This will energize the start relay whenever the key switch is in crank position and let the engine start.

3. Eliminate both the PASSkey module and the start relay. The relay is located on the driver side kick panel. Unplug the relay permanently and jump the large purple and yellow wires. The wires will be energized whenever the key switch is in the crank position. All the relay and PASSkey wiring is not needed.

Re: Bypassing VSS buffer box
 

Well I got the car started by grounding the blk/wht wire from the VSS connector. This appears to be a common ground used in several other circuits from my reading. I also connected C and F as well. I haven't been able to try it out again, but at least the car starts now. I still have to figure out the tach though, this is using a harness Pocket built for me so it is very much plug and play. However, I don't know if I will still need to boost circuit tied into the tach feed to get it to work. Setting the tach to 4/6/8 doesn't seem to matter in HPtuners.

Re: Bypassing VSS buffer box
 

I recommend this way