1984 Trans Am build thread - turbo LQ4 & 4L80E 9 Attachment(s) i've been working on a 1984 Trans Am for awhile and figured i should start a build thread at some point. it's slow go due to having kids, but things have been progressing over the past year. i always liked the body lines of the 3rd gen TAs. my overall plans are a 500-600HP turbo LQ4 with a 4L80E and all your other typical upgrades - suspension, brakes, rear end, paint, etc... will mainly be a street cruiser, but would like to go to the track and autocross a couple times. my goal is to have the car ready for the 50th anniversary of the f-body event in Detroit, MI 2017. two years seems like a long time, but i've already have this car for 7 years and haven't done much until recently. it'll be here before i know it. i've been mainly accumulating parts the past couple years and slowly doing the bodywork with a friend of mine. the first f-body i had was a 1984 Trans Am. bought it for $50 in 2001. i ended up restoring it, but i was always chasing issues from previous owners. here's some before and after pics. Attachment 327982 Attachment 327983 i sold that car in 2008 after buying a clean roller for $500. i figured it was a better starting point for a ground-up build, but then i got sidetracked with a 1972 Camaro project. sold the Camaro last summer and am using those funds to get back to work on the TA. interior was worn & faded, but the body was pretty rust / rott free for being in WNY. Attachment 327984 Attachment 327985 Attachment 327986 Attachment 327987 Attachment 327988 Attachment 327989 Attachment 327990 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 8 Attachment(s) the first few things i did was install a non-A/C dash and clean up the floor. to property switch to A/C delete, i had to cut a hole for the vent in the upper dash cowl on the driver side. i made a template of the vent from another 3rd gen, transferred it to the cowl and made the new hole with a cutoff wheel. Attachment 327974 Attachment 327975 Attachment 327976 Attachment 327977 next i prepped the interior side of the floor boards for paint. i scuffed everything up and had to patch two small areas. i also welded in two mounting brackets for the hatch door option that this car didn't have. i'm not very good at welding, but no one will see these areas so it was good practice. i painted the whole floor with Duplicolor truck bed coating. looks nice and should hold up well. Attachment 327978 Attachment 327979 Attachment 327980 Attachment 327981 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 9 Attachment(s) we started working on the removable body parts first - doors, hood, fenders, etc... unfortunately the driver door had a bad dent right down the middle. we got that straightened out though. Attachment 327964 Attachment 327965 Attachment 327966 front fenders were in really good shape. Attachment 327967 Attachment 327968 Attachment 327969 next was the main body of the car. i thought it was pretty straight and rust free, but we did find some hidden stuff - mainly near the rear wheel wells. Attachment 327970 Attachment 327971 Attachment 327972 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 11 Attachment(s) since my friend who's helping with the bodywork is an hour away, he said it would be easier if i brought the car to his garage. that was this past fall. now he's doing stuff in his spare time, but making great progress. Attachment 327953 Attachment 327954 Attachment 327955 he even flushed in the rear side marker lights and fender vents. Attachment 327956 Attachment 327957 Attachment 327958 doors looking good. Attachment 327959 Attachment 327960 Attachment 327961 Attachment 327962 sneak peak - i'm planning to install door handles from a 2011+ dodge charger, but still working on how to do it. i quickly mocked up a handle in a spare door, but the handle depth inside the door could be a problem. it might fit if i have a glass shop trim the bottom corner of the window though. Attachment 327963 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 1 Attachment(s) i had planned to do an LS1 swap on this car, but then started researching turbo LQ4 builds on LS1tech. as luck would have it, a family member bought a new truck last year and sold me his 2000 Chevy 2500 pickup for $2,000. the truck had 200K on it, the LQ4 engine and a 2WD 4L80E. i ended up keeping the engine, tranny and all wiring and then parting out the rest of the truck. i ended up making $2500 so far and still have some parts laying around to sell. Attachment 327952 i've been picking up engine parts the past few months on craigslist and LS1tech mostly. so far i have a complete LS6 intake & DBC TB, f-body front accessories, plastic LS1 gas tank, f-body oil pan, LS6 dual radiator fans, f-body engine harness & PCM and aluminum 317 heads (since my engine had the iron 317s). still debating whether i want a machine shop to check the crank, pistons and rods or just buy new stuff. i don't have ton of money, but i also only want to build this thing once. i'll be doing all the standard upgrades to the engine - cam, pushrods, 5315 morel lifters, pac 1218 springs, LS9 head gaskets, ARP bolts, blah blah... i think i'm going to get the denmah turbo kit. read all his stuff on LS1tech - very informative. going to try and build all the piping myself. will also be upgrading to dual in-tank walboro pumps. not sure about the wiring of everything yet. i hate wiring so i might just buy a pre-made harness. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 10 Attachment(s) back to bodywork. next up was fixing the horrible fitment of the rear bumper. the bumper never lines up with the body lines. we'll fix that. Attachment 327942 Attachment 327943 Attachment 327944 Attachment 327945 Attachment 327946 bumper removed and epoxied to hold the cuts open. Attachment 327947 Attachment 327948 Attachment 327949 Attachment 327950 then mounted to hold it in position. now it fits like it should. Attachment 327951 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 5 Attachment(s) rear bumper is almost done. the ends fit smoothly with the quarter panels now. Attachment 327937 Attachment 327938 Attachment 327939 i also started fabricating an electric fuel door. i had a spare locking fuel door assembly without the thumb latch. i figured i could remove the lock, fill the hole and then mount some kind of popper on the door. smoothing the door was easy. finding a way to make it pop open was much harder. i got a fuel door assembly with an actuator from a VW jetta in the local junkyard. the latch part on the back of the jetta door was removed and grafted onto the TA door. still trying to mock up the actuator. the latch part definitely works, but the release may end up being something else. Attachment 327940 Attachment 327941 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Some great fab/body work! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E This should be a fun build!! Looks good so far! Justin |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Looking good so far! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Lookin good mofo |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Nice progress so far. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Subscribed! Very nice work! How did you smooth the marker lights and fender vents? I have an 83 I'm starting on body work. Those are some of the things I was unsure about how to do it properly. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by petrolhead
(Post 5888473)
Subscribed! Very nice work! How did you smooth the marker lights and fender vents? I have an 83 I'm starting on body work. Those are some of the things I was unsure about how to do it properly. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E i started a separate engine build thread on LS1tech. i'm hoping to get some input on my planned setup: http://ls1tech.com/forums/forced-ind...ut-please.html |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Cool build! Subd. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by battmann
(Post 5889253)
the marker lights and vents were installed using 3M panel bond on both sides. after that sets, you can do the body work to blend the body lines. I know that the vender vent gaps are pretty big, did you use anything special to fill those with? Thanks |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by petrolhead
(Post 5889656)
I know that the vender vent gaps are pretty big, did you use anything special to fill those with? Thanks |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 5 Attachment(s) rear bumper is done and in black primer. Attachment 327398 Attachment 327399 Attachment 327400 Attachment 327401 Attachment 327402 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 6 Attachment(s) i'll be installing the factory 1984 aeropackage ground effects on this car. the bumper i'm using is in great shape, but did not have these GFX. i bought the correct bumper with the GFX years ago so i'm using that bumper as a template to transfer the mounting holes i need onto the good bumper. the stock mounting brackets and hardware was totally rotted. we used flat steel and welded threaded rod to make new hardware brackets. then it was painted to prevent new rust. it turned out really well. the GFX still have a little waviness to them that we'll have to try and straighten out better. Attachment 327392 Attachment 327393 Attachment 327394 Attachment 327395 Attachment 327396 Attachment 327397 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 3 Attachment(s) my friend also worked on the electric fuel door some more and got it working. i don't know all the details of how he did it yet, but i'll be going there this weekend to check it out. apparently he used a Cadillac STS release. Attachment 327389 Attachment 327390 door latches disassembled, cleaned and reassembled. Attachment 327391 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Who is going to fab the 80E crossmember? I've been searching for months, can't find one for sale! Wanna make an extra??? :) |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by BrutalT/A
(Post 5891127)
Who is going to fab the 80E crossmember? I've been searching for months, can't find one for sale! Wanna make an extra??? :) actually BMR used to make a 80E crossmember for third gens, but i just checked and they must not carry it anymore. i probably won't get to the engine & tranny mock-up until early summer. i'll post pics of what i come up with and can make another one to sell if you like it. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by battmann
(Post 5891178)
i plan to fab the crossmember myself. i had to fab one when i put a 4L80E in a 1972 Camaro i used to have so i'm pretty sure i'll be able to figure something out. i'm going to be using BMR's trak pak torque arm kit so i won't have to worry about connecting the torque arm to the tranny. actually BMR used to make a 80E crossmember for third gens, but i just checked and they must not carry it anymore. i probably won't get to the engine & tranny mock-up until early summer. i'll post pics of what i come up with and can make another one to sell if you like it. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E
Originally Posted by battmann
(Post 5890942)
i just filled the gap with panel bond and made it flush with the fender. after that a skim coat of body filler. i'm hoping i won't get any cracks down the road. the best way to do it would be to have a fender vent fabricated out of metal and then weld it on, but i don't have the skills or money to pay for that to happen. I just bought some panel bond for another project, I like the look, so I will try it too. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Nice thread. Subscribing! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 1 Attachment(s) worked on the car some more a couple weekends ago. unfortunately we didn't get too much done, but we did get the hood and fenders mounted on the car and aligned for blocking. the gaps look great and are about the width of a paint stir stick everywhere. my friend says he's going to try and fabricate the rear hood bulge trim piece out of metal so it can be welded on and smoothed. he said this piece can't be glued in with 3M panel bond because the heat from the engine and direct UV from the direct will eventually make it crack. hopefully he can fabricate this piece. i also checked out the electric fuel door popper and i guess it's from a early 90s Cadillac Eldorado. the release works with a catch on the back of the fuel door. a car alarm hood sensor actually pops the fuel door out. the sensor is spring loaded and makes an alarm go off if your hood is opened, but in my application when you hit the release button the spring sensor pushes the fuel door open. pretty slick. there's also a cable emergency release on the assembly in case the thing fails. Attachment 327104 i also officially started my engine build. the LQ4 was completely torn down. everything inside looked great. cylinders weren't scratched and no bearings were burned up. some of the main bearings still had a sheen on them and this engine had 200K miles. i took the block, crank and heads to a local machine shop. they quoted me $300 to clean all the parts, check the parts for cracks and measure everything. if everything checks out then i'll probably bore the block 30 over, get a valve job done on the heads and start reassembling the engine. i'm still researching the parts i want, but hope to finalize that soon. it looks like i'll be putting all new stuff in the engine and only keeping the stock crank. it's a little more expensive, but i only want to put this thing together once. i'm not sure if i'll have the machine shop assemble the shortblock or if i'll do it myself. i'll have to see what they charge. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E been awhile since i posted an update. haven't really done much on the car lately. i did purchase all my engine parts from Colorado Speed mid-April. i've received everything except the ARP head studs, rods and pistons. as soon as those parts come in, i'll be able to have the machine shop do all their work and assemble the short block for me. also been selling extra stuff i have laying around so i can buy more parts. not sure what i should focus on getting next: fuel system, computer / wiring, rebuild the 4L80E or get the turbo kit. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 3 Attachment(s) i finally received the rest of my engine parts last Thursday. Friday i took off of work and got all of the engine parts to the machine shop. i should have took pictures, but i'm never very good at remembering. engine should take about two weeks to machine and assemble. pretty much everything but the crank and valves will be new. i got all of the following:
i also scored an AMAZING deal today. i found a bolt-in Ford 9" rear end for third-gen f-bodies locally on craigslist. rear is a professionally made product with Moser 31 spline axles and stock bolt pattern, new auburn posi unit, 4:11 gears and was all rebuilt with new parts this past fall. guy was asking $1250. these rears go for anywhere between $2500 and $3300. guy said he wanted to put his car back to stock and this rear was way overkill for the factory tuned port engine so he figured he'd sell it to help fund the restoration. he said he needed to get a stock rear end so i offered to give him mine plus cash and he agreed. ended up getting this differential for $1000 cash and my stock rear. i'll probably change the brakes over to LS1 or Corvette discs and install lower gears in it, but i'm pretty excited i found this locally. Attachment 325876 Attachment 325877 Attachment 325878 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Sweet deal on that axle! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 6 Attachment(s) made some more progress recently. i had a local shop (Northeast Machine in Tonawanda, NY) do the machine work and assemble the short block for me. that got done a couple weeks ago. here's the finished product. Attachment 325243 Attachment 325244 last week i started assembling the rest of the engine at my friend's shop. he's an hour away from me so it's hard to get there. i got the block prepped & painted and then put the heads on. i'm using all ARP hardware to make sure this thing stays together. i tried putting the oil pan on, but it looks like the windage tray i got with some other parts is from a 5.3 engine and won't allow the f-body oil pickup tube to bolt on. just my luck. Attachment 325245 Attachment 325246 also made a little progress on the body. this Trans Am didn't come factory with the full ground effects so we had to weld on the correct rocker brackets to hold them on. luckily i saved these brackets from a car i parted out years ago. Attachment 325247 Attachment 325248 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Coming along nicely! Cant wait to see future updates. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Looking good clint |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E ordered my turbo kit yesterday. i had a $250 gift card i got from work that i forgot about so that helped offset the cost a little. i should receive everything in about a week or two. i ended up getting this kit: http://www.vsracing.net/catalog/prod...03008384cbc014 then i upgraded to this turbo: http://www.vsracing.net/catalog/imag...04_1811471.jpg http://www.vsracing.net/catalog/prod...386d44cd2ac694 also ordered v-band clamps & flanges for my truck exhaust manifolds and a turbo blanket: http://www.vsracing.net/catalog/imag...%20Blanket.jpg http://www.vsracing.net/catalog/images/P1010023.jpg |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 4 Attachment(s) been awhile since i posted progress pics. got the engine finally buttoned up last month. also received the VS racing GT45 80mm billet turbo kit. Attachment 323727 Attachment 323728 Attachment 323729 also won an ebay auction for a Pontiac arrow dealership sign. was $250 with shipping. the guts of the sign was missing, but i bought two $30 LED undercounter lights from Home Depot and got it working. looks awesome! Attachment 323730 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Cool build & I like the light! :thumbsup: |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 1 Attachment(s)
Originally Posted by PurelyPMD
(Post 5963452)
Cool build & I like the light! :thumbsup: i actually have a vintage, unused 1984 Trans Am billboard too. it's 8' high by 21' wide. got it off ebay years ago for $100. i need a bigger garage to display all this accumulated stuff. Attachment 323684 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Gotta love the sign! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 8 Attachment(s) got a lot done this past weekend. engine and tranny went in. i used Spohn's LSX swap mounts and the engine sits about 1/4" low on the passenger side. i'll probably put shims between the engine mounts and block. 4L80E tranny fits good though. i had to cut an ear off of the driver side bell housing for it to fit. tranny only slightly hits the tunnel on the passenger side. i'll need to massage the tunnel slightly and it will be good. we the started to fabricate the 4L80E crossmember. seems like what we came up with will work. need to finish welding it and then paint it. i wanted to make sure the member allowed clearance to take the pan off for tranny servicing. installed some of the steering so it's easier to move the car around. also installed the subframe connectors, suspension and Ford 9" rear. i have koni yellows but don't want to put them in until after paint. still need to weld in the BMR trak pack torque arm. springs are Eibach pros. car sits high, but it's also pretty much gutted. hopefully it'll settle down once the car is back together (which is going to be awhile). Attachment 322922 Attachment 322923 Attachment 322924 Attachment 322925 Attachment 322926 Attachment 322927 Attachment 322928 Attachment 322929 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 12 Attachment(s) made a little more progress lately. we've been working on getting the hood straighter and installed some door handles I bought from Kindigit Design. they look awesome! i was originally going to try and install handles from a 2011-2013 dodge charger, but the part inside the door is pretty bulky and they just don't fit. Attachment 320400 Attachment 320401 Attachment 320402 Attachment 320403 Attachment 320404 Attachment 320405 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E How do those work? Do you push them in? |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Yes - you push on the rear of the handle and the front pivots out so you can garb it & open the door. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E Sounds nice! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 3 Attachment(s) time to update this thread. didn't realize how long it's been since i added to it. we've really just been slowly doing bodywork since my last post. pics below were from the end of summer 2016. car finally all in primer. Attachment 316373 Attachment 316374 Attachment 316375 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 12 Attachment(s) now for some major news! the car finally has some paint on it. my friend is finishing the bodywork and painting the car at his work: Mill-Stream Collision in Tonawanda, NY. they're doing an AMAZING job! we're trying to go for a Foose inspired build. there's a lot of subtle modifications being done to the car. stuff most people wouldn't realize unless they are familiar with the third-gens:
Attachment 316361 Attachment 316362 Attachment 316363 Attachment 316364 Attachment 316365 Attachment 316366 Attachment 316367 Attachment 316368 Attachment 316369 Attachment 316370 Attachment 316371 Attachment 316372 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 10 Attachment(s) went to check on the car yesterday and the body now has paint on it. bumpers and ground effects are next. the pictures don't do it justice. it looks awesome. we're going to hold off on the engine bay for now. we need to figure out where all the holes need to be for the wiring and turbo piping. after that we can pull the motor to paint the engine bay. Attachment 316251 Attachment 316252 Attachment 316253 Attachment 316254 Attachment 316255 Attachment 316256 Attachment 316257 Attachment 316258 Attachment 316259 Attachment 316260 |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E You paint those Kin dig it handles body color or black? I really want them for my second gen |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E They'll be body color. |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E update!?!?! |
Re: 1984 Trans Am build thread - turbo LQ4 & 4L80E 6 Attachment(s) Updates you want - updates you get! LOL Two weekends ago we masked off the suspension and painted the undercarriage. I'll have to remove all the suspension later and paint some areas, but at least most of the underside has coverage now. Attachment 315758 Attachment 315759 Attachment 315760 i also had my friend add a fender well support on the driver side to match the passenger side one. i got the idea from the DSE build thread Attachment 315761 Attachment 315762 lastly was i saw a thread where gthmcty1 installed blinkers in his side mirrors . i thought it looked pretty cool so i started mocking up doing something similar on my mirrors. here's the shape i came up with. Attachment 315763 also ordered the CXRacing LS1 turbo kit. they're having a 10% off sale right now. all the pipes are pre-made which will save me a lot of time. so now i'll be selling the other kit i already bought last year. https://cimg2.ibsrv.net/gimg/www.thi...b7363581f8.jpg biggest score was i picked up an original Mecham rear spoiler somewhat locally. guy actually saw my build thread on LS1tech and PMed me seeing if i was interested in buying it. needs some work, but it will look awesome. https://cimg2.ibsrv.net/gimg/www.thi...3fc725afca.jpg next weekend i'm hoping to mock up the engine bay stuff and then pull the drivetrain to have the bay painted. it will be the same color as the body, but more eggshell sheen. |
All times are GMT -5. The time now is 04:32 PM. |
© 2024 MH Sub I, LLC dba Internet Brands