Post Your 60ft with Suspension Setup Heres Mine 60ft- 1.27 Tire- M/T 28x10.5 slick Spohn Anti Roll Bar Spohn LCA's Spohn Torque Arm -2.5 pinion Angle LCA Relocation Brackets (using stock hole) QA1 DA Rear Shocks Set at 12 Comp, 12 Rebound Lakewood 90/10 Fronts limited to 3" of travel (I'am converting to Strange Mustang Struts soon) |
Re: Post Your 60ft with Suspension Setup 1.82 street tire lcarbs one hole down boxed lca's 3 way adjustable ce eninering drag shocks v8 1le springs in the rear 1le swaybar rear stock front struts stock v6 springs no front swaybar 1.74 same as above except on a 28x10.5x15 drag slick |
Re: Post Your 60ft with Suspension Setup Should also post tranny/gearing/weight and estimated power to get an idea how well the car is working. 1.41 60 foot 383 HSR + 150 shot my best. ~500-520whp 26x11.50x15 ET Streets/ skinnies up front. stock 10 bolt 3.42 gear, 3600 stall (3800-4000 on 150 shot) Th700R4 trans 3450lb raceweight Full bolt on factory style Spohn suspension, LCA's with relocation brackets on bottom hole. Spohn SFC's, Spohn torque arm ~ 2.5 pinion angle. Panhard bar Eibach pro-kit springs, tokico 5 way adjustable shocks/struts. Softest setting up front, medium out back 8 point roll bar. Stock 36/24mm sway bars TDS wonderbar steering brace |
Re: Post Your 60ft with Suspension Setup Iroc adio : Please post your E.T/MPH/60FT with the 377 motor you were selling. Post with the 200 shot also. |
Re: Post Your 60ft with Suspension Setup
Originally Posted by Fast 383
(Post 4542278)
Iroc adio : Please post your E.T/MPH/60FT with the 377 motor you were selling. Post with the 200 shot also. |
Re: Post Your 60ft with Suspension Setup 1.17 - with the rear tires, lol. Rear: std 4-link(3/4 holes, not a trick one yet), arb, QA1 single adj/95# springs, 33x10.5W's Front: stock strut/spindle(monroe gas-matics FTW!), 10" 175# springs, 1-2" down travel, custom k-member/lower rails & control arms. 3000-3050 race weight, 4.56 gear, Th400, bbc + spray |
Re: Post Your 60ft with Suspension Setup 1.51 60ft lcarbs, using middle hole spohn rear sway bar no front swar bar spohn lca spohn crossmember mickey et street radials |
Re: Post Your 60ft with Suspension Setup 1.33 no front sway bar pa racing coilovers 90/10 lake woods jegster ta jegster lca's relocation brackets in bottom hole stock sway bar preloaded on the left side airbag right rear custom valved shocks 325/50/15 Hoosier Dr's |
Re: Post Your 60ft with Suspension Setup this topic sounds familiar :) 1.25 spinning with 4.56 gear, 1.25 on the rear tires with 3.90 gear and 1.29 on the bumper ! random tech torque arm (stock length) homemade lcarbs. sbc on a single kit, with a progressive controller and it isnt all in at the 60 lol 225 shot 28/10.5 at 3340 race weight |
Re: Post Your 60ft with Suspension Setup
Originally Posted by car_fixer
(Post 4543090)
this topic sounds familiar :) 1.25 spinning with 4.56 gear, 1.25 on the rear tires with 3.90 gear and 1.29 on the bumper ! random tech torque arm (stock length) homemade lcarbs. sbc on a single kit, with a progressive controller and it isnt all in at the 60 lol 225 shot 28/10.5 at 3340 race weight 9.30 on NOS |
Re: Post Your 60ft with Suspension Setup
Originally Posted by Iroc Adio
(Post 4543108)
the 377 went 10.70 N/A 9.30 on NOS Thanks!!! |
Re: Post Your 60ft with Suspension Setup
Originally Posted by Fast 383
(Post 4543316)
Thanks but I am really looking to know what the MPH was on those runs. I have the same times and the same NOS kit and want to know if your MPH was like mine. Thanks!!! 9.30 was 148mph |
Re: Post Your 60ft with Suspension Setup Awsome I would love to see a 9.0- 9.39 @ 150MPH pass with my combination going 126 on motor. That would be hitting with the 250 pills. |
Re: Post Your 60ft with Suspension Setup You would have me covered :) |
Re: Post Your 60ft with Suspension Setup 1.56 60'. this was on a 12.02 @ 111 pass stockish ls1 with boltons, 3600 stall converter, 4.11 gears, 29x9 hoosier -Jegster torque arm, non adjustable -bmr lcarb's -spohn non-adj panhard rod -spohn spherical rod ended 'moly lca's -cut v6 springs all the way around -chassis engineering cheapo shocks set in the middle (30/70 maybe?) -iroc rear sway bar -no front sway bar -8pt roll bar -jegster bolt in sfc's that i welded in. |
Re: Post Your 60ft with Suspension Setup 1.7 on a 11.98 @ 111mph pass 9x30x15 M/T slicks 4.10 gears bone stock torque arm Founders Performance LCA's Jegster SFC's |
Re: Post Your 60ft with Suspension Setup 1.55-11.52@120 moroso trick springs up front/ v6 cargo springs in the back with a bag on the right lakewood 90/10 struts, comp enginering 50/50 shocks spohn torque arm boxed lower control arms lcarb with arms mounted in the lowest hole stock sway bars front and back 28x9 m/t drag slicks no roll cage yet or frame connectors, and the car launches perfectly level Done with a 305 with heads, cam, and blower. t-56 with a stock clutch and 4.11 gears |
Re: Post Your 60ft with Suspension Setup
Originally Posted by Orr89RocZ
(Post 4543394)
You would have me covered :) |
Re: Post Your 60ft with Suspension Setup haha, same here man. I've been 1.41 60' above on the stock rear as well but not close with the turbo motor. Your car on a 250 hit would seriously stress that rear but if you progressive hit it or spray top of first gear, it should hold :) You'd still have me |
Re: Post Your 60ft with Suspension Setup I think the rear is smoked after the last track outing(12/09). I just put it on the trailer and wrote it off. Now I'm back together after the new 10 point cage install and will have it out on Saturday. If it's not broken and still ticking I bought the 100HP pills to set up for 10.0 index. Hopefully it will stay together with that tune but I doubt it. Would suck to get all the way out in your area for the big grudge match (:D) to find out it was maxed out 100HP ago :( . |
Re: Post Your 60ft with Suspension Setup Well I just got my best 60ft the other day. Oh and I did it with 26x10's!!!!!!!!!!!! stock suspension. Car also ran a new best et as well... stock suspension vari shocks in rear sw coilover in front 4.10 gears glide 26x10 et drags. 1.24 60ft 8 sec 1/4 mile |
Re: Post Your 60ft with Suspension Setup Would suck to get all the way out in your area for the big grudge match () to find out it was maxed out 100HP ago |
Re: Post Your 60ft with Suspension Setup 1.38 3200 lbs, stock suspension on a true 28x10.5 glide w/ 4.11 gear |
Re: Post Your 60ft with Suspension Setup 1.61 60ft all stock V6 car suspension with air bags well worn V6 front shocks M/T 26x8.5x 15 et streets 3530# w driver 11.92@115 |
Re: Post Your 60ft with Suspension Setup 1.22 60 ft. backhalved 1985 with 4 link, 4.56 gears, 32x14 Hoosiers, glide .040 over 350 SBC + 200 HP N20 ~2800 lbs with driver 8.95@148 best time (so far) Some nice cars-heavy hitters-on here ... great to see! Mike |
Re: Post Your 60ft with Suspension Setup Not a drag racer, just a once a month special event racer. I have a modded 1991 L98 with Edelbrock LCA and Panhard Bar with 3:73 and Goodyear CS-C tires. My 60' times are around 2.10, but I just had a set of ALSTON SFC welded in. My question is will the SFC help at all with my launch? |
Re: Post Your 60ft with Suspension Setup 1.31 so far with the 275 goodyear drag radials. stock shortblock LT1, factory ported heads, hydro roller, ~210-250ish shot of nitrous. hughes th400, fti converter. ~3100lbs. s&w torque arm pa kmember/arms lca's, panhard relocation brackets stock '99 ss springs moroso front springs wolfe swaybar koni spa-1's all around i think the car should go a 1.29 next time out. |
Re: Post Your 60ft with Suspension Setup We posted a 1.58 60 ft last night at 99.80 mph. The E.T. was a 7.01. That is on a stock chassis with only a 100 shot of nitrous. It ran like an 8.15 on motor no NOS. |
Re: Post Your 60ft with Suspension Setup
Originally Posted by thumper115
(Post 4545569)
We posted a 1.58 60 ft last night at 99.80 mph. The E.T. was a 7.01. That is on a stock chassis with only a 100 shot of nitrous. It ran like an 8.15 on motor no NOS. 6.560 594 ft 7.018 1/8 et 98.46 1/8 mph shifting at 6500 rpm's 1.583 60 ft 6.586 594 ft 7.037 1/8 et 99.80 1/8 mph shifting at 7,000 rpm's |
Re: Post Your 60ft with Suspension Setup little behind on this post but hey better late than never. TH350,4200 stall, moser 12 bolt w/4.30, jegster non-adj. torque arm, lakewood lift bars, 90/10 lakewood in front and 3-way summits in back set on 50/50. 1.563 60ft. 11.68 @ 115.04 on hoosier drag radials P255/50R16 |
Re: Post Your 60ft with Suspension Setup bone stock suspension minus both sway bars, no frame connectors, 27x10.5 QTP's = 1.56 added a set of spohn non adjustable lca's and relocation brackets = 1.51 |
Re: Post Your 60ft with Suspension Setup ^put the rear sway bar back on and i bet it runs 1.49 :) |
Re: Post Your 60ft with Suspension Setup 1.29 is the best it`s been, norm is a 1.35 Stock suspension 29x10.5 hoosier slicks Qa1 r series single adjustables 110# 10 inch springs wolfe anti roll wolfe panhard spohn torque arm rod end LCA`s 90/10 lakewoods 200# 10 inch coil overs pro fab lower a arms and k member |
Re: Post Your 60ft with Suspension Setup I managed a couple of 1.29's but normally it's in the low 1.3 range. Depends a lot on track prep. |
Re: Post Your 60ft with Suspension Setup http://img20.imageshack.us/img20/5351/scan0002kf.jpg I'm in the left lane. You can see more here. Ths transition of a lowly Suburban motor to a high 11's street pounder for around $3000 Setup is Spohn performance torque arm and tranny crossmember with driveshaft loop. Hotchkiss boxed lower control arms and a Moser 12 bolt with a 4:11 gear. Need frame connectors but weld in only. Here's a short movie my son made. He couldn't get the camera to work right on the first pass and I had .5007 light. |
Re: Post Your 60ft with Suspension Setup Guess i will throw mine in: Slipping the clutch at 6000, 1.78 60 Spohn TA, BMOR non adj LCAs, BMR panhard, stock RS springs, stock replacement shocks and struts, WS6 swaybar still connected, CE welded in sub frames on a 26x11.5x16 ET street on stock 91-92 Camaro wheels. New 60 to be determined with no front sway bar, more weight reduction, carb that will not stumble off the launch, jetting up the carb. |
Re: Post Your 60ft with Suspension Setup 1.7 60' Spohn LCA relocation brackets bottom hole and boxed LCA's. Stock IROC-Z suspension except for lowering springs and poly bushings throughout. Monroe Sensa Tracs. 26x10 McCreary treaded bias ply slicks. 3700 lbs/700R4/3.27 Foot brake 3000rpm launch. 290 rwhp. 12.7 @ 105. |
Re: Post Your 60ft with Suspension Setup 1.28 with a 4200 stall, all stock suspension. The front tire only lifts an inch or less. The car weight was 1900 front, 1550 rear. Th weight bias has changed for this year. Once the car is back together I'll post the front to rear ratio. |
Re: Post Your 60ft with Suspension Setup 1.629 footbrake, 3500 10" converter, 3.73 geared 10 bolt, boxed stock LCA's with alum. bushings, LCARB's, summit 3 ways, set at 50/50, Alston Race Cars TA, -2.0 pinion. 90/10's up front with trick springs. 28x10.5 Stiffies 12.2's @108 |
Re: Post Your 60ft with Suspension Setup
Originally Posted by 1BADRZ28
(Post 4795967)
1.28 with a 4200 stall, all stock suspension. The front tire only lifts an inch or less. The car weight was 1900 front, 1550 rear. Th weight bias has changed for this year. Once the car is back together I'll post the front to rear ratio. |
Re: Post Your 60ft with Suspension Setup
Originally Posted by 88IROC350TPI
(Post 4797363)
all stock? as in all factory original stock parts? or stock style? |
Re: Post Your 60ft with Suspension Setup 1.26 60 ft 9" with BMR T/A Wolf Double adjustable lowers Strange Single Adjustable Shocks 3200lbs |
Re: Post Your 60ft with Suspension Setup ^^so the BMR arm is worth .01 over the spohn? notice any other differences in the way the car left? consistency increase or decrease? which bmr arm did you get? |
Re: Post Your 60ft with Suspension Setup 1.43 60', Pete Z bars, stock rear springs and sway bar, air bag in both springs, QA1 shocks, stock torque arm. E.t. was 10.98 @ 118. |
Re: Post Your 60ft with Suspension Setup
Originally Posted by mw66nova
(Post 4800118)
^^so the BMR arm is worth .01 over the spohn? notice any other differences in the way the car left? consistency increase or decrease? which bmr arm did you get? |
Re: Post Your 60ft with Suspension Setup My old BBC Camaro: Spohn TQ arm, Comp universal Sway Bar, Stock mounting position, lakewood 90/10s.. 1.34 60ft (Rear tires) best.. My old 406 87 FBird: Jegs TQ arm, stock sway, Lakewood Fronts with coil overs, th700 trans.. 1.41 NA best ft brake, 1.38 spraying at 20MPH (Stock 10 bolt) :) My current 94 FBird: Same rear susp, Strange adjustable fronts with stock coils, T56 6 Speed...1.45 dumping the spec 3 at 6k.. Can still improve on that number though, looking to hit low 1.40s if I ever fix the cracked block.. |
Re: Post Your 60ft with Suspension Setup Update was a 1.6 60 letting off the clutch at about 5000. |
Re: Post Your 60ft with Suspension Setup
Originally Posted by stiletto
(Post 4800442)
BMR Xtreme T/A. i never had a spohn T/A |
Re: Post Your 60ft with Suspension Setup Best 60' I've ever had was at SGMP last Feb. 1.367 on 28x10.5's 3215 lbs. Spohn adjustable torque arm, rear drag sway bar and panrod bar. Hotchkis LCA's in stock location no relocation brackets. All stock front suspension with about 1" travel. |
Re: Post Your 60ft with Suspension Setup How did I miss this? anyways, here's mine. 1.52 60ft. 11.796 @ 118mph. pump gas 350sbc. 3.80 in a moser 9". Converter flashing at 5400rpm on the T-brake. approx 3200 lbs. no front sway bar Stock cut coils and stock shocks front and rear. Home made adj panhard bar Home made relocation brackets in bottom hole Sphoon lca's unknown adj torque arm with heims. stock sway bar preloaded on the left side airbag in the right rear |
All times are GMT -5. The time now is 06:51 PM. |
© 2024 MH Sub I, LLC dba Internet Brands