Third Generation F-Body Message Boards - Search Results

 
Search: Posts Made By: Tuned Performance
Showing results 1 to 50 of 499
Search took 0.07 seconds.
Forum: V6
Yesterday, 10:51 PM
Replies: 1
Views: 42
Posted By Tuned Performance

Re: 2.8 v6 will not start

Whatís your fuel pressure?
Yesterday, 05:45 PM
Replies: 6
Views: 89
Posted By Tuned Performance

Re: Putting a 1991 T5 into a 1989 TH700R - speedo cable

You might check with tpi parts.net to see if this would do the trick.
https://www.tpiparts.net/inc/sdetail/7587
Forum: DFI and ECM
Yesterday, 02:56 PM
Replies: 3
Views: 72
Posted By Tuned Performance

Re: the problem with the emulator

If it has a ribbon cable make sure it’s orientation is correct.
Forum: DFI and ECM
Yesterday, 02:22 PM
Replies: 3
Views: 72
Posted By Tuned Performance

Re: the problem with the emulator

How does it connect to the ecm without a memcal ?
error code 51 ?
Forum: DFI and ECM
Yesterday, 12:18 PM
Replies: 8
Views: 424
Posted By Tuned Performance

Re: Camaro 305HO TPI 1988 5speed

There are two sensors on the front of the intake . One for the cold start injector. The other for the ecm to tell it the engines coolant temperature. I don’t think that’s the stalling issue. When the...
Yesterday, 12:03 PM
Replies: 3
Views: 100
Posted By Tuned Performance

Re: OBD1 readers

Moates.net xtreme aldl or 1320 electronics
06-16-2019, 07:09 PM
Replies: 1
Views: 146
Posted By Tuned Performance

06-16-2019, 02:24 PM
Replies: 1
Views: 146
Posted By Tuned Performance

91,92 hood blister decals

Carbon fiber look, $20 shipped priority in the states...
Forum: DIY PROM
06-16-2019, 02:16 PM
Replies: 4
Views: 226
Posted By Tuned Performance

Re: Maf sensor disassembled with a question? Help

I do t see the diodes but I see two resistors.
06-16-2019, 12:10 PM
Replies: 17
Views: 25,769
Posted By Tuned Performance

Re: How to I read check engine codes?

Look at the link on post #10
06-14-2019, 08:41 PM
Replies: 4
Views: 320
Posted By Tuned Performance

Re: Good engine oil tube?

The zz4 dipstick and tube works on the l98
06-13-2019, 07:24 PM
Replies: 3
Views: 287
Posted By Tuned Performance

Re: 1991 Z28 Fuel pump only 10 PSI

You need to stick to one thread
https://www.thirdgen.org/forums/tech-general-engine/762030-1991-z28-tpi.html

ep241 delco
Forum: TPI
06-13-2019, 12:12 PM
Replies: 14
Views: 369
Posted By Tuned Performance

Re: No spark

https://easyautodiagnostics.com/gm/4.3L-5.0L-5.7L/distributor-mounted-icm-tests-6
Forum: TBI
06-12-2019, 10:29 PM
Replies: 17
Views: 2,555
Posted By Tuned Performance

06-12-2019, 08:31 PM
Replies: 2
Views: 317
Posted By Tuned Performance

Re: 1991 Z28 TPI

What’s your fuel pressure at ?
Have you ohmed your injectors cold and hot ?
Forum: TBI
06-12-2019, 07:52 PM
Replies: 5
Views: 352
Posted By Tuned Performance

Re: Tbi problem please help

Any stores codes ?
Have you checked base timing and fuel pressure ?
Forum: DIY PROM
06-12-2019, 07:42 PM
Replies: 2
Views: 326
Posted By Tuned Performance

Re: 1988 l98

Yes, but if there oem multecs there not worth swapping in.
contact southbay fuel injectors.
Forum: Electronics
06-12-2019, 12:43 PM
Replies: 5
Views: 352
Posted By Tuned Performance

Re: Is it possible to disable check engine light???

https://www.thirdgen.org/forums/electronics/255251-light-driver-module.html

Picture of the module
Forum: DIY PROM
06-12-2019, 12:08 PM
Replies: 29
Views: 822
Posted By Tuned Performance

Re: Knock retard w/o knock detected?

Could this be piston slap ?
Jeff had mentioned to me the engine was honed out to address oil burning.
was it honed to much to cause a loose fit of the pistons ?
Forum: Electronics
06-12-2019, 12:03 PM
Replies: 5
Views: 352
Posted By Tuned Performance

Re: Is it possible to disable check engine light???

https://www.thirdgen.org/forums/electronics/644213-engine-light.html

I think it’s on the passengers side under the dash.
Forum: Electronics
06-12-2019, 11:58 AM
Replies: 5
Views: 352
Posted By Tuned Performance

Re: Is it possible to disable check engine light???

Ccc there is a lamp driver module I think if you remove it the mil will go off.
06-11-2019, 06:47 PM
Replies: 5
Views: 409
Posted By Tuned Performance

Re: Need some help troubleshooting ECM PROM

https://cimg4.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/5863a0fa_f0c7_4fcb_a936_8d3309d705cb_5e25e7df66859b7edcc83eb05468f29e7419fb3e.jpeg
06-11-2019, 06:25 PM
Replies: 5
Views: 409
Posted By Tuned Performance

Re: Need some help troubleshooting ECM PROM

$135 for a anjf or $150 shipped for a $150 sold as is .
They are unmodified factory memcals
Forum: V6
06-11-2019, 02:36 PM
Replies: 22
Views: 961
Posted By Tuned Performance

Re: Wrong reading of the coolant temp

The fan command on is 106.25c or 223f
Forum: V6
06-11-2019, 02:09 PM
Replies: 22
Views: 961
Posted By Tuned Performance

Re: Wrong reading of the coolant temp

As far as a prom goes you need a pocket programmer or equivalent.
Your ecm uses a 2732 prom. You can solder in a adapter from moates.net and use a eeprom and a burn 2 programmer. For software you...
Forum: Electronics
06-11-2019, 01:03 PM
Replies: 15
Views: 396
Posted By Tuned Performance

Re: O2 heating time?

New ecm throwing a code 51 ?
Forum: Engine Swap
06-11-2019, 12:57 PM
Replies: 7
Views: 515
Posted By Tuned Performance

Re: Sourcing a Junkyard 350 for TPI Build

:yup: if you planning to use junk yard injectors they might be varnished up.
89-91 Vettes use a multec injector that the coils fail on.
budget money for injectors and contact southbay fuel...
Forum: Electronics
06-10-2019, 08:12 PM
Replies: 4
Views: 376
Posted By Tuned Performance

Re: Code 12 on '91 Trans Am with no start

Injectors ohms, Sounds like the vats is working since it give a voltage to the ecm.
For checking injector pulse use a noid light.
Forum: Electronics
06-10-2019, 06:01 PM
Replies: 4
Views: 376
Posted By Tuned Performance

Re: Code 12 on '91 Trans Am with no start

Check the voltage at the ecm pin f10. It should be 2.5v key on.
This is the passkey hz signal to the ecm.
Are you getting 12v to the icm pink wire ?
wouldn't worry about the code 12
have you...
06-10-2019, 12:45 PM
Replies: 20
Views: 1,317
Posted By Tuned Performance

Re: Idol Only???

The vacuum leak and higher idle while setting the base timing shouldn’t be effected. As long as you set the timing correctly with the est disconnected. As far as the high idle check for vacuum leaks...
06-10-2019, 12:31 PM
Replies: 5
Views: 409
Posted By Tuned Performance

Re: Need some help troubleshooting ECM PROM

If your using a piggyback adapter for the tune aujp, or any vette 90-91 l98 memcal will work.If you decide to buy a memcal lmk I have anjf and aujp.
Unfortunately I quit loaning out things after...
06-09-2019, 11:38 PM
Replies: 1
Views: 376
Posted By Tuned Performance

Re: Mystery Grey Connector

A picture would help, sounds like the ignition power wire and tach wire.
06-08-2019, 08:39 PM
Replies: 7
Views: 37,784
Posted By Tuned Performance

Forum: TBI
06-07-2019, 06:20 PM
Replies: 363
Views: 321,295
Posted By Tuned Performance

Re: How to: 305 To 350 swap....everything you need to know

The closest calibration for your ecm is atjp or anlu.
Forum: TBI
06-07-2019, 05:17 PM
Replies: 363
Views: 321,295
Posted By Tuned Performance

Re: How to: 305 To 350 swap....everything you need to know

Sonoma92 what are you working on ?
year make model, ecm service number?
Forum: DFI and ECM
06-06-2019, 12:25 PM
Replies: 9
Views: 963
Posted By Tuned Performance

Re: 87 C100 Connector for Trans Am

Look at c207 for a hot wire. Iirc should be one with a pink/blk stripe.
Forum: Electronics
06-06-2019, 12:00 PM
Replies: 12
Views: 763
Posted By Tuned Performance

Re: Installing Holley Sniper, have questions

Do you have a schematic showing the yellow wire or does it say coil negative?
Forum: TPI
06-06-2019, 11:45 AM
Replies: 14
Views: 369
Posted By Tuned Performance

Re: No spark

Glad your on the right track, replace the mat/iat Is a good idea the 12v might of fried the resistor.
Forum: Electronics
06-05-2019, 08:13 PM
Replies: 12
Views: 763
Posted By Tuned Performance

Re: Installing Holley Sniper, have questions

Your correct on the white wire.
Forum: Electronics
06-05-2019, 07:01 PM
Replies: 12
Views: 763
Posted By Tuned Performance

Re: Installing Holley Sniper, have questions

https://cimg6.ibsrv.net/gimg/www.thirdgen.org-vbulletin/790x400/beeac7b9_ecdd_438a_abed_fe4088983d32_2442ffe200ca01bd6b43bfdb1cfc9303e058b635.jpeg
The tach wires run through c100 itís a white wire...
06-05-2019, 06:39 PM
Replies: 7
Views: 375
Posted By Tuned Performance

Re: OEMcats.com

If anyone has discontinued parts it’s vintage parts.org

https://www.vpartsinc.com/

They buy dealers nos parts
Forum: TPI
06-05-2019, 03:17 PM
Replies: 14
Views: 369
Posted By Tuned Performance

Re: No spark

Correct, I have seen a break in the jumper wire before.
if that checks out fine the new icm is more than likely the issue.
...
Forum: Cooling
06-05-2019, 03:05 PM
Replies: 9
Views: 676
Posted By Tuned Performance

Re: What Brand Thermostat and How to Make the Single Electric Fan Come On Sooner

https://cimg1.ibsrv.net/gimg/www.thirdgen.org-vbulletin/900x1266/c156da8d_8074_4516_86ca_c185482595ff_b25d35b69ba337b9295059ff063aa4e6f6e2f271.jpeg
Forum: Cooling
06-05-2019, 03:02 PM
Replies: 9
Views: 676
Posted By Tuned Performance

Re: What Brand Thermostat and How to Make the Single Electric Fan Come On Sooner

You can run the relay ground side to a sw555 temperature switch for lower on and offs but it’s much easier to have the memcal reburned. Stock 226-228f on is normal as gd said. 200f on and 185 off...
Forum: Electronics
06-05-2019, 12:47 PM
Replies: 12
Views: 763
Posted By Tuned Performance

Re: Installing Holley Sniper, have questions

Is your speedometer cable drive ?
The tach can be hooked to the negative side of the ignition coil.
Forum: Cooling
06-05-2019, 12:15 PM
Replies: 21
Views: 1,521
Posted By Tuned Performance

Re: Rpm problem once warmed up

Here is the adx needed

https://www.thirdgen.org/forums/dfi-ecm/759994-datalogging-w-1228746-a.html
Forum: Cooling
06-05-2019, 12:11 PM
Replies: 21
Views: 1,521
Posted By Tuned Performance

Re: Rpm problem once warmed up

The software is free, Tuner pro rt and $61 adx.
moates.net has the xtreme aldl cable 1.
06-05-2019, 11:52 AM
Replies: 1
Views: 517
Posted By Tuned Performance

Re: Stalls when put in gear or at a stop?

Could be your iac, clean and reset minimum idle speed.
This could also be injectors have you ohmed them ?
Forum: TPI
06-05-2019, 11:40 AM
Replies: 14
Views: 369
Posted By Tuned Performance

Re: No spark

Are you getting voltage at the icm pink wire ?
Forum: DFI and ECM
06-04-2019, 02:25 PM
Replies: 1
Views: 192
Posted By Tuned Performance

Re: Reprogram the ECU for OBD-I

You can get the best results by tuning it yourself.
You will need a few things from moates.net
xtreme aldl and cable 1, burn 2 and a g1 adapter.
You will also want to pick up a few eeproms...
Showing results 1 to 50 of 499
 


 
Forum Jump

Contact Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.