Third Generation F-Body Message Boards - Search Results

Search: Posts Made By: Dholland17
Showing results 1 to 17 of 17
Search took 0.01 seconds.
11-06-2018, 08:41 PM
Replies: 3
Views: 279
Posted By Dholland17

Re: New to me - 1983 Z

Haven't done much to her besides pull the heads off. I'm dropping the oil pan with it in the car to replace it.
The engine looks fresh inside, pistons read bored .040 over.

I want the Vortec...
Forum: Exhaust
11-05-2018, 04:31 PM
Replies: 3
Views: 2,059
Posted By Dholland17

Re: build your own 3" direct catback

Anyone point me to an affordable 3" exhaust all the way back? The below is old but should I rely on the parts listed as known good? Thanks!
I need headers and Y pipe too...full redo of my exhaust if...
Forum: Electronics
10-19-2018, 05:07 PM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

Ok, success. G5 wire was out, looks like it disconnected somewhere along the firewall. Where does that connect? It is always hot so should I splice it in-line with the A4 wire? When I did that as a...
Forum: Electronics
10-19-2018, 02:31 PM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

Using this as well.

So looks like I have no power from the firewall on plugs F4 and G5. Need to back track those now...
Fun fun fun…
...
Forum: Electronics
10-19-2018, 01:07 PM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

These are my guides but I need help here for sure...

http://austinthirdgen.org/mkportal/modules/contents/images/Fig11_1983_body_wiring.gif
...
Forum: Electronics
10-19-2018, 01:01 PM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

Fusibles tested ok, and I have power at the firewall on these 2 ports only, the pink and red I am holding in the attached.


If I have no power at CTSY I guess I need to chase from the firewall in...
Forum: Electronics
10-19-2018, 09:18 AM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

ok I have measurable power at starter and one pin on the c100. Should I have more than one always hot at the c100?
I have power at some fuses but nothin gat the CTSY! Help, that must be my issue...
Forum: Electronics
10-19-2018, 08:30 AM
Replies: 6
Views: 948
Posted By Dholland17

Re: Bulkhead connector and electrical questions

Does the starter fusible link tie directly to a power distribution plug on the c100? Meaning, if some of my fuses have power and the CTSY does not, does that still point to possible fusible links?...
10-18-2018, 02:31 PM
Replies: 109
Views: 5,942
Posted By Dholland17

Re: 17x9 IROC wheels coming from Hawks!!!

I couldnít wait so picked up an oem set of 16x8 iroc to refinish for $200. No curb rash but quite a bit of cleanup/prep. I figure Iíll soda blast and paint. Anyone have a link to the oem silver and...
10-15-2018, 08:43 PM
Replies: 109
Views: 5,942
Posted By Dholland17

Forum: Electronics
10-15-2018, 07:39 PM
Replies: 8
Views: 166
Posted By Dholland17

Re: Bulkhead connector/ test for power C100 wires

How do I test power at the starter first? I put my voltmeter in both posts and ground to the body and it reads zero. Battery reads 12.96 not running. Thanks!
Forum: Electronics
10-15-2018, 03:10 PM
Replies: 8
Views: 166
Posted By Dholland17

Bulkhead connector/ test for power C100 wires

Hi all,
i have no lights or cabin power. How do I backtest the c100 connections with a voltmeter? It looks like I have no fusible links at the starter, wires soldered together etc. Car is a project...
Forum: Electronics
10-15-2018, 12:56 PM
Replies: 6
Views: 948
Posted By Dholland17

Re: Bulkhead connector and electrical questions

Hi all,
chasig down a problem with no headlights and cabin power. I do have brake lights and rear directionals only and the carbíd 1983 Z starts fine. I pulled the c100 but dinít Know how to test it...
10-08-2018, 01:16 PM
Replies: 109
Views: 5,942
Posted By Dholland17

Re: 17x9 IROC wheels coming from Hawks!!!

Bummer. Spoke to Hawks today, the 17x9 year 85-87 wonít be avail until beginning of the year. Anyone know who sells something I can get now that looks original? Thanks all!
10-07-2018, 10:50 PM
Replies: 109
Views: 5,942
Posted By Dholland17

Re: 17x9 IROC wheels coming from Hawks!!!

Good to know thanks Abubaca! Will be calling them tomorrow, love the wheels in the pics, hope they look the same in person :)
Irocs, 17x9 Hawks...
10-07-2018, 05:47 PM
Replies: 109
Views: 5,942
Posted By Dholland17

Re: 17x9 IROC wheels coming from Hawks!!!

I really want these 17x9 Iroc wheels for my project. I canít wait the 6 months so can anyone tell me where I can buy something comparable please?!
09-24-2018, 09:48 PM
Replies: 3
Views: 279
Posted By Dholland17

New to me - 1983 Z

My first Camaro: 1983 Z28 from rust free Arizona. Let the fun begin. Has a 350 crate in it.
...
Showing results 1 to 17 of 17


 
Forum Jump

Advertising
Featured Sponsors
Vendor Directory

Contact Us Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.