the chrome parts are rolling in so the first set of chrome parts are rolling in https://s25.postimg.org/hlxty7dpb/20170810_181321.jpg so the gold zink parts will go to a new home...would be killer on a black car. https://s25.postimg.org/yaz9u4aan/20170810_181842.jpg another week and the hood hinges heater box..and other parts should be done... NOTE: FOUNDERS PARTS (PLATES) ARE NOT POWDER COATED the set same to me from them in a red paint/epoxy. on a good point it was easy to remove.. but is advertised as a powder coat finnish |
Re: the chrome parts are rolling in Looks like very nice quality work. |
Re: the chrome parts are rolling in comes with a life time warrenty.... |
Re: the chrome parts are rolling in thinking of doing the tie rods & center link.... will order them today..so all the Gold zink stuff will going up for sale.. all the gold parts are new..gold kink plate..rust free for life..going to post them for sale $160 shipped https://s25.postimg.org/dadtmxw67/20140813_184625.jpg |
Re: the chrome parts are rolling in hood hinges look good..will post some pics |
Re: the chrome parts are rolling in Did you forget to do the thin V-stamped fender support rods (down low) or did you just like them body color so much you couldn't do it? :) |
Re: the chrome parts are rolling in :) |
Re: the chrome parts are rolling in
Originally Posted by jmd
(Post 6161051)
Did you forget to do the thin V-stamped fender support rods (down low) or did you just like them body color so much you couldn't do it? :) are you asking about the one on the driver side in front of the tire? I had it done in gold zink.. photo below..it bolts up the frame. nexed to the steering box... hood latch support was dropped off today. the v shaped brakets on ea side of it (black) I had done with the parts I picked up today...as nobody is making a billet set.. I had to go with Chrome.but I will never have to buff them out!.(there are some fender rods 12" to 14" in long.. body color..thay are stayn..) https://s25.postimg.org/45sw95sm7/20150805_164538.jpg https://s25.postimg.org/7a3k5y9en/20170814_164622.jpg https://s25.postimg.org/5aid0sppb/20170814_164506.jpg https://s25.postimg.org/zbhljneov/20170814_164442.jpg E Brake levers..had been just to close to the rim..so I got a 2nd set..cut them down 1/8 inch and will install.. the others look so good. I did not want to trim them.. this set(below) of E brake Levers are just to long..(ya can see they are longer then the set above) https://s25.postimg.org/5al491jbz/20150724_185311.jpg this was made by a member on this site...I had to cut the (what they think are welds) down to buff out the mess..and then have it buffed out to a like chrome finnish..its nexed..look close ya can see the weld mess in front..the photo was Deceiving..no biggy..we made it look 1000 times better..(this is a before I got it shot) before the part was on anybody's car.. what I got was a mess...but its going to look better then this photo! https://s25.postimg.org/itlvknggv/im...fcf3983490.jpg |
Re: the chrome parts are rolling in a few more parts..this one had the GM bumps removed..to look better.. for some reason GM had a bump/dent in the upper face..they are on all of the GM Hood supports...not this one any more... https://s25.postimg.org/m02837sbj/20170830_183759.jpg |
Re: the chrome parts are rolling in That's pretty. |
Re: the chrome parts are rolling in Very Nice! |
Re: the chrome parts are rolling in So when are you getting the entire car body chromed? |
Re: the chrome parts are rolling in
Originally Posted by //<86TA>\\
(Post 6166372)
So when are you getting the entire car body chromed? after all everybody has painted parts... if ya cant get billet parts..chrome what ya have..when I ordered the K member and A arms..I did ask for naked Steel...as I was going to plate them as well... but all they had was coated..so just left them red... started plating all the parts in gold zink....then wanted chrome..so I did a 2nd set of parts in chrome... |
Re: the chrome parts are rolling in billet center caps for my weld aluma star 2.0 wheels https://s25.postimg.org/f4n34rgnz/20170907_191345.jpg |
Re: the chrome parts are rolling in so this is what I picked up from this site....before reworking it..not a bad part..(they should have used rivets)...it would have looked better...but hay..it's a start...first removing most of that thing the looks like a weld...sorta of...removing by hand with a dremel tool...before repolish..new welds added on the under side... https://s25.postimg.org/p381r8q3j/im...fb9d10d49c.jpg |
Re: the chrome parts are rolling in this is 100% better looking https://s25.postimg.org/njda6gba7/20170912_182928.jpg a little work and its fixed https://s25.postimg.org/8bxam3jfj/20170912_183014.jpg |
Re: the chrome parts are rolling in
Originally Posted by articwhiteZ
(Post 6168461)
|
Re: the chrome parts are rolling in thanks...guys at the fab shop are sayn they could make this as a 1 piece unit. for resale..i asked them to make 1 or 2 and see what would cost..if they can and do.. ill post them.. |
All times are GMT -5. The time now is 03:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands