Third Generation F-Body Message Boards

Third Generation F-Body Message Boards (https://www.thirdgen.org/forums/)
-   Engine/Drivetrain/Suspension Parts for Sale (https://www.thirdgen.org/forums/engine-drivetrain-suspension-parts/)
-   -   [CA] Tremec T56 retrofit complete kit (https://www.thirdgen.org/forums/engine-drivetrain-suspension-parts/724379-tremec-t56-retrofit-complete.html)

topteam54 09-13-2015 03:00 AM

Tremec T56 retrofit complete kit
 
Decided on switching up my build. I have a T56 Tremec reotrofit trans that was rebuilt and upgraded internals(built and installed by DynoDon). Has the bell housing, trans, hydraulics, McLeod Clutch, steeda shifter(best shifter I've ever used), correct aluminum driveshaft(3.5" or 4"). From what I recall this places shifter in stock T5 location and allows the use of the stock speedo cable. Complete setup has approx 1000-1500 miles. Asking $2500 OBO for everything mentioned. Trans is located in So-Cal but can be shipped.

Gary Anderson 09-13-2015 07:54 AM

Re: Tremec T56 retrofit complete kit
 
Can you post pics of all that is included? What upgrades were done?

topteam54 09-13-2015 12:07 PM

Re: Tremec T56 retrofit complete kit
 

Originally Posted by Gary Anderson (Post 5961104)
Can you post pics of all that is included? What upgrades were done?

Trans is still on vehicle. I'll be pulling the engine out in the next week or so. As far as upgrades from what I recall parts were sent out for some treatment to harden the parts. Along with a full performance rebuild. Has the 2.97:1 first gear ratio.

topteam54 09-18-2015 03:52 PM

Re: Tremec T56 retrofit complete kit
 
Bump open to offers. Also willing to trade for a 12 bolt, 9", dana 44 or 60.

Gary Anderson 09-19-2015 06:47 AM

Re: Tremec T56 retrofit complete kit
 
What crossmember does this setup use and is it included?

peterc005 09-19-2015 08:39 AM

Re: Tremec T56 retrofit complete kit
 
What additional parts would be required to use this unit to replace a T700 behing a L98 350 SBC?

jmd 09-19-2015 09:53 AM

Re: Tremec T56 retrofit complete kit
 

Originally Posted by peterc005 (Post 5963218)
What additional parts would be required to use this unit to replace a T700 behing a L98 350 SBC?

flywheel & bolts
clutch & pressure plate bolts
pilot bearing
crossmember (fab one)
PROM for the ECM
pedals and neutral safety switch
NSSwitch connector and wiring
floor sealing boot
shifter trim boot and console trim
reverse light connector and wiring

That's nearly it.

topteam54 09-19-2015 11:20 AM

Re: Tremec T56 retrofit complete kit
 

Originally Posted by Gary Anderson (Post 5963212)
What crossmember does this setup use and is it included?

Modified factory one. I can include it in the package deal.

Originally Posted by peterc005 (Post 5963218)
What additional parts would be required to use this unit to replace a T700 behing a L98 350 SBC?

Everything on the list above except you're getting the flywheel, clutch assembly and all the hardware with it. Also I can include the trans crossmber. I'm sure I can find a new pilot bearing and include it.

hanke777 10-05-2015 02:26 AM

Re: Tremec T56 retrofit complete kit
 
Will it bolt up to a 409 chev motor?

topteam54 10-06-2015 12:21 AM

Re: Tremec T56 retrofit complete kit
 
Sorry forgot to update. Sold last week


All times are GMT -5. The time now is 03:42 PM.


© 2024 MH Sub I, LLC dba Internet Brands