383 Stroker with FIRSTŪ TPI 39 Attachment(s) Last edited: 05-07-2024 See post #24 for anyone interested in tuning, I have attached my final .bin (S_AUJP v6.0) at post #24 or https://www.thirdgen.org/forums/diy-...first-tpi.html See post #33 for update after 3900miles, 5 years (summers) https://www.thirdgen.org/forums/engi...ml#post6518510 ___________________________________________________________________________________________________________________ Thought I'd post my results on swapping the LB9 305TPI (1991) T5 with a 383 Stroker with FIRSTŪ TPI intake T56. Please feel free to ask questions in the comments. Hopefully that will help others interested in this kind of swap. I posted some T/HP numbers at the end. This is not for argument or debate or bragging. It is just for comparison and to give an idea of what can be accomplished (give & take). There are many other set-up possible which would probably yield better numbers. That's not the point here. However, feel free to add comments on how it can be improved as long as it's TPI, not LSX nor carbureted and street friendly. Engine is a 2018, 383 stroker GM crate SP383 Deluxe (GM part #19355672 assembled in Mexico):
334rwhp @ 4912rpm 412rwt @ 3803rpm Estimated Dynojet results (for comparison): 360rwhp @ 4912rpm 445rwt @ 3803rpm Flywheel estimated: 400hp @ 4900rpm 494t @ 3800rpm BSFC 0.53 (12.8AFR / 32# / 83%DC / 13.4V) GM rated with Chevrolet Performance Eliminator Vortec Intake Manifold, Holley 770cfm 4 barrel carburetor, 1.75" long tube headers: 435hp @ 5600rpm 445t @ 4600rpm MotorTrend test: 446hp @ 5600rpm 448t @ 4600rpm https://www.motortrend.com/how-to/te...t-performance/ Loss of peak HP due to TPI long runners = -10.3% Car weights 3525lbs full gas tank. With me in it 3700lbs. On Toyo TQ drag radial 275/45R16 (15psi), at track, 3.89 Motive rear gear. Moser 9in, Eaton Detroit Truetrac, I get @ 65Deg.F 50% Humidity 101 Baro (321' elevation): Best 1/4 mile 60' 1.954 330' 5.359 1/8 8.185 MPH 87.10 1000' 10.532 1/4 12.629 Speed 111.88 mph 0-60mph 4.84sec Estimated 1/4 mile with full engine potential 12.2 sec @ 116 mph For comparison with TGO member @my hemi who has similar set-up with AT with drag tires at track https://www.thirdgen.org/forums/alte...k6ki2vediNhMiQ 60' 1.671___1.683 330' 5.026___5.057 1/8 7.847___7.879 MPH 87___87 1000' 10.283___10.313 1/4 12.350___12.376 Speed 109___109 mph Also, the old modified LB9 with SLP cold air, TPI air foil, TB coolant by-pass, SLP underdrive pulleys, 1 5/8 shorty headers, Y pipe 2.75" with high flow cat to 3" single, hyperteck chip (160°Thermo). Dynojet results: 238rwhp @ 4500rpm 312rwt @ 3400rpm Estimated: 270hp @ 4500rpm 354t @ 3400rpm Best 1/4 mile 14.0 @ 98 mph 0-60 6.0sec https://cimg0.ibsrv.net/gimg/www.thi...c0aeda3291.jpghttps://cimg7.ibsrv.net/gimg/www.thi...024822b3bb.jpg https://cimg7.ibsrv.net/gimg/www.thi...227df07861.jpg https://cimg0.ibsrv.net/gimg/www.thi...0a77cf0ed5.jpg https://cimg1.ibsrv.net/gimg/www.thi...036cce8659.jpg https://cimg2.ibsrv.net/gimg/www.thi...9719aebb93.jpg |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by SbFormula
(Post 6441622)
Thought I'd post my results on swapping the LB9 305TPI (1991) 5MT to a 383 Stroker with FIRSTŪ intake 6MT. Please feel free to ask questions in the comments. Hopefully that will serve others interested in this kind of swap. Engine is a 383 stroker GM crate SP383 Deluxe (GM part #19355672):
60' 1.652 330' 5.196 1/8 8.135 MPH 84 1000' 10.636 1/4 12.708 Trap Speed 108 0-60mph 4.5 Mustagn Dyno Results: 334rwhp @ 4912rpm 412rwt @ 3803rpm Converted to Dynojet: 360rwhp @ 4912rpm 445rwt @ 3803rpm Flywheel estimated: 410hp @ 4912rpm 505t @ 3803rpm https://cimg0.ibsrv.net/gimg/www.thi...c0aeda3291.jpg https://cimg7.ibsrv.net/gimg/www.thi...227df07861.jpg |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by Fast355
(Post 6441738)
Bet that is a hoot to drive with all the torque. |
Re: 383 Stroker with FIRSTŪ intake swap Nice build! I'm working on a similar project and I'm looking to purchase some shorty headers. What kind of modifications had to be done on your header flanges to work on your Vortec heads? |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by carlos64030
(Post 6463198)
What kind of modifications had to be done on your header flanges to work on your Vortec heads? 1) They fit perfectly with no clearance issue on my set-up 2) Zero cost at the time 3) Nothing available that would fit my single exhaust set-up for OEM M5 bellhousing and transmission crossmember/torque arm set-up 4) Optimal headers (1 3/4" primary for Vortec heads port) would have required expensive modifications to hydraulic clutch, bellhousing, crossmember/torque arm set-up and exhaust system. I know they are not optimal for power. I get robbed some HP for sure. In my case it was irrelevant. For someone else it could be a big issue. I decided to match the gasket to the headers and not the exhaust port. It seals perfectly using the Mr. Gasket copper #7150MRG. The picture shows the mismatch with bolt holes. That's the part that had to be modified on the gasket and headers flange. Using a carbide bit, the holes had to be elongated precisely so the gasket and flange would match. I used the gasket as a template so the exhaust ports would be "centered aligned". As you can see on the picture, the gasket is not optimal for the exhaust port shape. The installation was done with engine on stand so I could match everything correctly. Trying to do this with the engine in the engine bay is probably impossible. IMO the best option is full on custom headers. That requires expertise and $$$$. If I ever find that kind of expertise around my neck of the woods, I will consider it. I don't know how much HP at the wheel it represents though. https://cimg7.ibsrv.net/gimg/www.thi...8f48649724.jpg |
Re: 383 Stroker with FIRSTŪ intake swap I really like your Thread so far, and I like your Engine Swap Project. Now that most people are swapping to the Gen-III/ Gen-IV SBC Engine instead of the Gen-I SBC Engine... I really like to see these Swaps! :nod: I am in now way shape or form trying to diminish what you have done. However I would like people to know that they can do a Swap like yours, for roughly the same budget... And optimize the Build with a little research into Valve Events and Engine Performance... And walk away with Power in the range of what you are making, up to another 100ish Horse-Power and 40 to 50 Ft/ Lbs of Torque. People do not need to swap to a Gen-III/ Gen-IV SBC Engine, to have a 500 to 550 HP Engine that is very streetable. Congrats on your Swap! :nod: And again, it's great to see a Gen-I SBC Build!!! :nod: |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6463536)
I really like your Thread so far, and I like your Engine Swap Project.
Originally Posted by vorteciroc
(Post 6463536)
I am in now way shape or form trying to diminish what you have done. However I would like people to know that they can do a Swap like yours, for roughly the same budget... And optimize the Build with a little research into Valve Events and Engine Performance... And walk away with Power in the range of what you are making, up to another 100ish Horse-Power and 40 to 50 Ft/ Lbs of Torque. http://www.rcsracingengines.com/Perf...evy%20EFI.html |
Re: 383 Stroker with FIRSTŪ intake swap Awesome! Thank you! :nod: And Yes, you are correct, as the Intake-Manifold is a BIG restriction. The TPI Configuration would have to go... You are not going to see those High Power Numbers at Atmospheric Pressure. :nod: |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6463561)
And Yes, you are correct, as the Intake-Manifold is a BIG restriction. The TPI Configuration would have to go... Here's an interesting chart comparing the SP383 Deluxe with the FIRSTŪ TPI Intake vs. GM Eliminator Vortec Intake Manifold with Holley 770cfm carburetor (what GM tested it with). For my needs, on the street, I find the TPI gives me more usable HP, specially in town when I want to keep the rev down. I never drag race and rarely do standing start accelerations. I like quick low rpm rolling accelerations. It keeps the law enforcement at bay. Getting to a stunting charge 0.1 or 0.2 sec faster is irrelevant lol. Just food for thought. It all depends on the application and what one wants. Also, what kind of HP/TQ the drive train and chassis are able to take.https://cimg2.ibsrv.net/gimg/www.thi...86f0a6996d.jpg |
Re: 383 Stroker with FIRSTŪ intake swap These GM 383s are awesome engines. I have the short block with AFR heads and a little milder cam than the SP383, and then a miniram intake. it is freaking crazy how much torque it puts out. |
Re: 383 Stroker with FIRSTŪ intake swap I am not familiar with the "First Intake". Are you referring to an Intake Manifold... or an Air Induction System? |
Re: 383 Stroker with FIRSTŪ intake swap |
Re: 383 Stroker with FIRSTŪ intake swap :nod: |
Re: 383 Stroker with FIRSTŪ intake swap However with a TPI intake, 500-550 peak HP could be difficult. https://www.thirdgen.org/forums/tpi/...be-runner.html |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6463652)
I am not familiar with the "First Intake". Are you referring to an Intake Manifold... or an Air Induction System? I corrected some of the thread but can't correct the title. I see someone gave you the link https://firstfuelinjection.com/ Cheers |
Re: 383 Stroker with FIRSTŪ intake swap Your Cylinder Heads have raised Exhaust-Ports... There should be a Gasket Set that is intended to fit. Raised Intake or Exhaust Ports are much more common in Higher Performance Heads. |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6463919)
Your Cylinder Heads have raised Exhaust-Ports... There should be a Gasket Set that is intended to fit. Raised Intake or Exhaust Ports are much more common in Higher Performance Heads. Here's what GM Performance recommends: "The SP383 High Performance engine should be installed with a pair of high performance headers for maximum performance. The headers used during development of the SP383 had 1.75" diameter primary tubes. Primary tubes were approximately 32.00" in length and had 3.00" diameter collectors. Using a similar combination in your application, along with a performance exhaust system with a balance tube (“H” pipe) and low restriction mufflers, will provide you with optimum performance from your SP383 High Performance engine." |
Re: 383 Stroker with FIRSTŪ intake swap Which (Brand/ Model/ Part Number) "Vortec" exhaust gaskets did you try? If the dimensions of the Gasket were correct or even close... And they did not seal well... Some of these Gaskets (depending on what material they are made of) can be doubled-up to seal better. :nod: |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6464138)
Which (Brand/ Model/ Part Number) "Vortec" exhaust gaskets did you try? If the dimensions of the Gasket were correct or even close... And they did not seal well... Some of these Gaskets (depending on what material they are made of) can be doubled-up to seal better. :nod: :yup: The Fel-Pro 1470. But I have to explain better lol. I was worried, the gasket (#1470) would not seal properly by looking at the mock-up. Those headers were not made to fit the Fast burn heads. The headers flange has a round matting surface were the round copper gasket fits nicely. Since the headers flange was already interfering with the port exhaust anyway, I decided to play safe and go with the round copper gasket. Would the #1470 gasket had sealed? Maybe. Would I had taken a chance? No. Doubling-up could have created a bolt length problem and also clearance issue. Let's say, I went with the easy and safe route the day I had to make the decision... among many many other decisions. :burnout: |
Re: 383 Stroker with FIRSTŪ intake swap Unless your Header Flanges are perfectly straight (which most of the time they are not) the Copper Gaskets will not seal well. "Dead-Soft" Aluminum Gaskets are amazing... Otherwise I would definitely try a different Material than Copper (no plain Paper either; they blow-out very easily). |
Re: 383 Stroker with FIRSTŪ intake swap GREAT WRITE UP!!! I am getting ready to drop my sp350/357 crate/FIRST TPI intake and wondering if ya used '6in. or '8in. external Harmonic balacer? |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by jasper21
(Post 6476396)
GREAT WRITE UP!!! I am getting ready to drop my sp350/357 crate/FIRST TPI intake and wondering if ya used '6in. or '8in. external Harmonic balacer? 8in, GM part# 12498008, https://www.summitracing.com/parts/nal-12498008 It came installed with the GMP crate engine. |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by vorteciroc
(Post 6464145)
Unless your Header Flanges are perfectly straight (which most of the time they are not) the Copper Gaskets will not seal well. |
Re: 383 Stroker with FIRSTŪ intake swap 8 Attachment(s) Here's the final .bin (S_AUJP v6.0) for my set-up. Many, many, many hours went into this with years of continuous learning. https://www.thirdgen.org/forums/diy-...first-tpi.html |
Re: 383 Stroker with FIRSTŪ intake swap A++ outstanding information on before and after results. Excellent build and enjoyed reading very much! |
Re: 383 Stroker with FIRSTŪ TPI
Originally Posted by SbFormula
(Post 6441622)
Last edited: 02-18-2023 Thought I'd post my results on swapping the LB9 305TPI (1991) T5 with a 383 Stroker with FIRSTŪ TPI intake T56. Please feel free to ask questions in the comments. Hopefully that will help others interested in this kind of swap. I posted some T/HP numbers at the end. This is not for argument or debate or bragging. It is just for comparison and to give an idea of what can be accomplished (give & take). There are many other set-up possible which would probably yield better numbers. That's not the point here. However, feel free to add comments on how it can be improved as long as it's TPI, not LSX nor carbureted and street friendly. Engine is a 2018, 383 stroker GM crate SP383 Deluxe (GM part #19355672 assembled in Mexico):
334rwhp @ 4912rpm 412rwt @ 3803rpm Estimated Dynojet results (for comparison): 360rwhp @ 4912rpm 445rwt @ 3803rpm Flywheel estimated: 400hp @ 4900rpm 494t @ 3800rpm BSFC 0.53 (12.8AFR / 32# / 83%DC / 13.4V) GM rated with Chevrolet Performance Eliminator Vortec Intake Manifold, Holley 770cfm 4 barrel carburetor, 1.75" long tube headers: 435hp @ 5600rpm 445t @ 4600rpm MotorTrend test: 446hp @ 5600rpm 448t @ 4600rpm https://www.motortrend.com/how-to/te...t-performance/ Car weights 3525lbs full gas tank. With me in it 3700lbs. On Toyo TQ drag radial 275/45R16, on the street, 3.89 Motive rear gear. Moser 9in, Eaton Detroit Truetrac, I get @ 77Deg.F 40% Humidity 103 Baro (sea level): Best 1/4 mile 60' 1.652 330' 5.141 1/8 8.019 MPH 86 1000' 10.435 1/4 12.456 Speed 111 mph 0-60mph 4.5 For comparison with TGO member @my hemi who has similar set-up with AT https://www.thirdgen.org/forums/alte...k6ki2vediNhMiQ 60' 1.671___1.683 330' 5.026___5.057 1/8 7.847___7.879 MPH 87___87 1000' 10.283___10.313 1/4 12.350___12.376 Speed 109___109 mph Also, the old modified LB9 with SLP cold air, TPI air foil, TB coolant by-pass, SLP underdrive pulleys, 1 5/8 shorty headers, Y pipe 2.75" with high flow cat to 3" single, hyperteck chip (160°Thermo). Dynojet results: 238rwhp @ 4500rpm 312rwt @ 3400rpm Estimated: 270hp @ 4500rpm 354t @ 3400rpm Best 1/4 mile 14.0 @ 98 mph 0-60 6.0sec UPDATE: For anyone interested in tuning, I have attached my final .bin (S_AUJP v6.0) at post #24 or https://www.thirdgen.org/forums/diy-...first-tpi.html https://youtu.be/vzCfPr2yKU4 https://cimg0.ibsrv.net/gimg/www.thi...c0aeda3291.jpghttps://cimg7.ibsrv.net/gimg/www.thi...024822b3bb.jpg https://cimg7.ibsrv.net/gimg/www.thi...227df07861.jpg https://cimg1.ibsrv.net/gimg/www.thi...036cce8659.jpg https://cimg2.ibsrv.net/gimg/www.thi...9719aebb93.jpg https://youtu.be/HD0QQd_g_MU What do you shift at.. we found ours is only shifting at 5000 rpms leaving a little on the table she managed a best of 12.2 at 110 I want her to shift at 5500 rpms I think she'll pick up a .1 or .2 we'll be going out in a few months hopefully... |
Re: 383 Stroker with FIRSTŪ TPI
Originally Posted by my hemi
(Post 6494250)
What do you shift at.. we found ours is only shifting at 5000 rpms leaving a little on the table she managed a best of 12.2 at 110 I want her to shift at 5500 rpms I think she'll pick up a .1 or .2 we'll be going out in a few months hopefully... Good question I believe, the theory is to maximize average HP on each gear (the area under the curve). So your shift points should be based on your engine HP curve, but also transmission gear ratios. I have a T56, you have an AT. So it might be hard to compare. On my 1st to 2nd to 3rd to 4th gear, it drops just over 1800RPM each time. So I did the math and I have to shift at 6000RPM (engine max RPM) on 1st-2nd and 3rd. From 4th to 5th it drops 1100RPM and from 5th to 6th it drops 1200RPM. So on the 4th and 5th there is no need to rev pass 5500RPM. Even if HP starts decreasing pass 5000RPM, there is less HP loss from 5000 to 6000RPM compare to the HP loss of shifting lower than 6000RPM. It's simple math. Plus I get the benefit of lower gear. Example (all things being equal): if I was to shift at 5000RPM on 3rd gear, it would drop to 3500RPM instead of 4200RPM on 4th gear. I would lose ave HP from 5000 to 6000RPM on 3rd gear (404 to 383HP) and gain ave HP from 3500 to 4200RPM on 4th gear (330 to 386HP). Simplified way of calculating the delta is using area of right triangle + area of rectangle. Let's say 25HP = 25 units and 50RPM = 50 units, basically 1 for 1. Loss of HP on 3rd gear Right triangle [((404-383)/25) * ((6000-5000)/50)]/2 = 8.4 Rectangle [(383/25) * ((6000-5000)/50)] = 306.4 Total loss 314.8 units Gain of HP on 4th gear Right triangle [((386-350)/25) * ((4200-3500)/50)]/2 = 10.1 Square [(350/25) * ((4200-3500)/50)] = 196.0 Total gain 206.1 units Delta = minus 108.7 units So I would rather push on the 3rd gear up to 6000RPM and gain 108.7 units of power combine with lower gear. For your AT, you'd have to see what can be done. Have no clue of your gear ratios and how AT can be adjusted. Not my cup of tea. I would say if it shifts at 5000RPM, it appears low, but it all depends where it lands. If you take my HP curve for instance. If it shifts at 5000RPM and lands around 4200RPM, there would be no gain, at first glance, in having it shift at 5500RPM and land at 4600RPM (the drop is accentuated the higher the rpm is). Maybe a gain in working longer on a lower gear though. If you compare your 1/4 mile to mine, you have faster ET because mine is almost a rolling start, but I get faster trap speed. So I would say, you are leaving HP on the table. Check this calculator online. It's a different explanation but the same principles. It uses torque numbers with gear ratios. It pretty much confirmed my own calculations. https://glennmessersmith.com/shiftpt.html Hope this helps. Probably more info on TGO about AT shift points with high performance TPI. https://cimg1.ibsrv.net/gimg/www.thi...0db61297b5.jpg |
Re: 383 Stroker with FIRSTŪ intake swap We have a 3.54 gear ratio the car imo i think will benefit from a higher shift point from 2nd to 3rd car imo still has more on top then 5000 rpms.. lol only true way to find out will be trial and error on the strip.. |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by my hemi
(Post 6494260)
We have a 3.54 gear ratio the car imo i think will benefit from a higher shift point from 2nd to 3rd car imo still has more on top then 5000 rpms.. lol only true way to find out will be trial and error on the strip.. Remember, the rear gear ratio does not affect the drop in RPM between transmission gear (shift). |
Re: 383 Stroker with FIRSTŪ intake swap Problem is the 700r4 has such a low 1st gear then it drops alot to second then 3rd..the transmission is setup uses a governor to make it shift at max rpm unfortunately it's set to a stock 305 or 350 tpi which we all now doesn't make much power past 4500 rpm so with the Change in the motor now with the bigger cu inch.. cam etc the stock shift points dont cut it imo..so for it to run as decent as it is only tells me it definitely has more in it..just sucks it can't be adjusted like modern day car thru the computer the 700r4 uses a TV cable and that governor only way it to manually shift it which is our next time out. |
Re: 383 Stroker with FIRSTŪ intake swap What intake gasket are you using with your First TPI and the fastburn heads? i see you are using the traditional 6 per side bolt pattern vs the vortec... i am doing a similar build and wondering on the intake gasket thanks and great looking build |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by alan91z28
(Post 6494484)
What intake gasket are you using with your First TPI and the fastburn heads? i see you are using the traditional 6 per side bolt pattern vs the vortec... i am doing a similar build and wondering on the intake gasket thanks and great looking build I used the FIRST TPI intake gasket. I believe it's a 1204 style but made to fit traditional or Vortec. Check with Ken at https://firstfuelinjection.com/ https://cimg5.ibsrv.net/gimg/www.thi...0e77be8217.jpg |
Re: 383 Stroker with FIRSTŪ intake swap UPDATE After 3900miles, 5 years (summers) As you can see, I don't drive it much. Around 800 miles per summer. It took a while to fix a drivetrain vibration, so the car sat more than it should have been. Vibration is finally fixed (https://www.thirdgen.org/forums/tran...s-another.html). This summer I was finally able to take it to an official dragstrip. It performed as expected with a 3700lbs, 400HP street car. All in all, I am very satisfied with the set-up. It does what it was intended to do. It performs really well on the street but lacks traction and top end at the dragstrip. Nothing surprising as the engine is rated at 6000rpm max and the TPI is restrictive. If you want it to perform at the dragstrip, you need a carburetor and more traction. The main thing is the whole set-up stays true to the "Formula" concept and TPI era. If not, well, I would have gone LS for sure. The engine is low maintenance. The spark plugs look good (inspected every spring) and compression is equal on all 8 at around 185psi. Spark plugs get a bit orange with the use of boostane. Easy to clean though. Oil pressure is always normal using Royal Purple 10W30. It gets a bit low at 850rpm warm idle, around 10 psi. I'm not worried. No leaks, no over heating, no weird noises. The valvetrain is a bit chatty, but it was like this from factory. Nothing over the top. No exhaust leaks despite the "funky" headers/vortec head fitment. I am a bit surprise with that. Fingers crossed! Engine warms up quickly on start-ups, way quicker than OEM. I like that. Engine, with this set-up, does not like the 1800-1900 rpm range. It feels like it's misfiring. Barely perceptible. I tried playing with the tune but nothing really works. Solution is to run the engine at lower RPM when cruising at mid speed. It actually increases fuel economy and quiets the loud exhaust. 50mp/h at 1600rpm yields 24mpg!!!!!!!!!! If you rev over 2000 rpm, mpg goes to sh** but the engine loves it. On the highway at 60-75 mph, it's perfect, the engine revs in the 2000-2300rpm. Average fuel economy, the way I drive, is 15mpg. If you baby it on highway, you can get 19mpg. One thing though. Oil consumption seems a bit much. I can't pin point what causes it. It's not leaking, the plugs are not fouled, it's not smoking or smelling. The blow by don't seem excessive. Compression is good, but did not do leak down test yet. The catch can yields less than 1 oz per 625 miles. I calculated the "burn" rate at 0.8 quarts per 700miles. I am not too worried about it for now. Engine break in was done according to GM's specs. However, I did not use engine break in oil, just conventional 10W30 then switched to synthetic after break-in period. I'll figure it out one day I guess. I have to take it on the highway for a day at steady cruise for a long run and see how it does for oil consumption (measure before and after). Nothing to worry in my case, but something to keep an eye on. The low-mid range rpm torque combined with the throttle quick response is phenomenal. I don't feel it as much because I'm used to it now. Still makes me laugh every time. If I take a passenger on, it instantly brings a smile to their face. Car feels fast and intimidating. Here's a statement from a 480 HP EV owner who rode shotgun with me: "you can get that much fun with an EV"... as he was grinning from ear to ear. The guy is a race car driver!!!! In the end, it's not all about numbers... and we are way too hard on ourselves when it comes down to evaluating our build. https://cimg0.ibsrv.net/gimg/www.thi...4dbe91735a.jpg |
Re: 383 Stroker with FIRSTŪ intake swap Great update... sounds like you are quite happy and having great fun with your set-up... I am just finishing a FIRST install and looking forward to it based on your reports! |
Re: 383 Stroker with FIRSTŪ intake swap
Originally Posted by alan91z28
(Post 6518537)
I am just finishing a FIRST install and looking forward to it based on your reports! |
Re: 383 Stroker with FIRSTŪ intake swap see my thread below starting around post 126 https://www.thirdgen.org/forums/engi...t-coupe-3.html |
All times are GMT -5. The time now is 08:43 PM. |
© 2024 MH Sub I, LLC dba Internet Brands