I did some updating! let's see yours!! 3 Attachment(s) Ok guys I needed to cheer myself up after all the egr mess I've been going through so I decided to clean up the engine bay a bit.I know we have some"Let's see your TBI engine bays" posts but it's been awhile since we've had some updated pics.Let's see what new with the Tbi crowd!! So, show me some new stuff guys! |
Originally Posted by robertfrank
(Post 3161393)
Ok guys I needed to cheer myself up after all the egr mess I've been going through so I decided to clean up the engine bay a bit.I know we have some"Let's see your TBI engine bays" posts but it's been awhile since we've had some updated pics.Let's see what new with the Tbi crowd!! So, show me some new stuff guys! I did some updating recently too. Along with the Heads/Cam swap I went with this baby. It has gone 9.3 @ 74 in the 1/8 with a 2.08s 60'. That is not bad for a Goodwrench 350 TBI, Ported TPI heads (1.94/1.60 valves), 9.85:1 compression, mild cam, Edelbrock 3704 TBI, 46mm TBI unit, and 1 1/2" primary headers. All in a 5,300 lbs Van with 3.07 gears. http://memimage.cardomain.net/member...2_193_full.jpg http://memimage.cardomain.net/member...2_197_full.jpg http://memimage.cardomain.net/member...2_198_full.jpg http://memimage.cardomain.net/member...2_199_full.jpg http://memimage.cardomain.net/member...2_200_full.jpg http://memimage.cardomain.net/member...2_201_full.jpg |
Heres a pic of my L03 i just finished, ill get some pics of the finished engine bay soon. Ultimate tbi mods, edelbrock performer intake, crane powermax 2032 camshaft, ported and polished 081 heads. http://viewmorepics.myspace.com/inde...eID=1518656970 Dammit! Hit the edit button instead of the quote button! Hope none of the post was lost |
Hey FAST355 I'm liking the Cadillac air cleaner. Lol. Looks good though. I got a question for you, do you have an aftermarket throttle body. If so what brand and what kind of horsepower increae did you get from it? Also was the throttle body spacer worth any horsepower? |
1 Attachment(s) Heres mine. It has the nylon/resin composit carb hat that extreme velocity used to make. Shame they still dont make it. The rest is a 350 with vortec heads, holley 670 TBI, edelcrap performer plus cam (204/214 .420"/.442"), 3" exhaust, 3.5" intake, etc. Doesnt wind real high. Only thing its really good at is turning the car into an unguided missle in first and breaking stuff. Still lots of fun on the street, though. |
1 Attachment(s) They still have the hat in aluminum, but its pricey. They also may still include the internal baffle, which would have to be cut out if using on TBI. |
Originally Posted by 1992camarors
(Post 3162173)
Hey FAST355 I'm liking the Cadillac air cleaner. Lol. Looks good though. I got a question for you, do you have an aftermarket throttle body. If so what brand and what kind of horsepower increae did you get from it? Also was the throttle body spacer worth any horsepower? My TBI unit is not an aftermarket piece, but it was bored over by Tom Bishop @ Extremefi. It is 46mm and has had the top flat milled and chamfered. The TBI spacer was a cheapy used one (for a 454) that I found on ebay. I think I paid less than $10.00 shipped to my door. I ran it as is for a while with a 454 TBI unit on it. I then pulled it off, cut the center out of it, smoothed everything out, and put it back on with the 46mm SBC TBI unit. I have since had the loose shaft 454 TBI unit bored to 54mm and bushings added to tighten the throttle shafts back up. The re-conditioned TBI unit really helped my idle quality by eliminating a fairly bad vacuum leak around the TBI shafts. |
Originally Posted by racnboy87
(Post 3161947)
Heres a pic of my L03 i just finished, ill get some pics of the finished engine bay soon. Ultimate tbi mods, edelbrock performer intake, crane powermax 2032 camshaft, ported and polished 081 heads. http://viewmorepics.myspace.com/inde...eID=1518656970 Dammit! Hit the edit button instead of the quote button! Hope none of the post was lost What belt line will you be using with those valve covers? I used the standard permiter bolt ones with mine and I had to beat the snot out of the pass. VC to get it to clear the alternator on my serp. system. |
1 Attachment(s) i just painted some stuff like 2 weeks ago... |
Originally Posted by dimented24x7
(Post 3162204)
Ok, lets try this again, lol. What belt line will you be using with those valve covers? I used the standard permiter bolt ones with mine and I had to beat the snot out of the pass. VC to get it to clear the alternator on my serp. system. |
3 Attachment(s) Here are a few pictures of the engine bay of my 91 Camaro vortec engine. |
bah, you guys made mine look like crap lol |
:iagree: Because it is... J/k lol |
Come on guys I KNOW there's more of us than this! show off guys. |
oops |
dimented24x7..................I had to turn the rear housing of the alt to get enough clearance to the battery connection which is the only problem that I had. I have a pic but cannot get the attachment link to work. Oh well.......... Happy New Years |
1 Attachment(s) Heres my before/after. I still have alot to do :) |
1 Attachment(s) dimented the upload worked today........wtf...........anyway it shows how I made it clear the valve cover. :) |
Here's mine before the latest update. http://i26.photobucket.com/albums/c1...g?t=1167664127 And here's after the latest update. http://i26.photobucket.com/albums/c1...g?t=1167664323 |
Here's a mostly stock L03 with 336k in my 89 Bird http://www.monchar.com/image.php?id=179055&f=179100/ |
https://www.thirdgen.org/forums/atta...ic101806_6.jpg http://https://www.thirdgen.org/foru...ic101806_7.jpg well its nothing special but nobody so far had nitrous on theres so i thought id put it up. sorry about the purge line not being there since i tried plastic(easy way) but it melted so i gotta get a new line. also i got a set of headers sitting up in my room at the moment getting ready to be put in. |
Originally Posted by Mongoose
(Post 3173303)
Here's mine before the latest update. http://i26.photobucket.com/albums/c1...g?t=1167664127 And here's after the latest update. http://i26.photobucket.com/albums/c1...g?t=1167664323 ----------
Originally Posted by DM91RS
(Post 3173264)
dimented the upload worked today........wtf...........anyway it shows how I made it clear the valve cover. :) |
Re: I did some updating! let's see yours!! hey would like to see some updated pics guys thanks |
All times are GMT -5. The time now is 03:56 AM. |
© 2024 MH Sub I, LLC dba Internet Brands