FS/FT: Midwest Motorsports Forged 355 -0 Miles- Perfect For Boost! IOWA
#1
Junior Member
Thread Starter
Join Date: Aug 2004
Location: Waterloo Iowa
Posts: 82
Likes: 0
Received 0 Likes
on
0 Posts
Car: Black 1984 Mazda Rx7
Engine: SBC
Transmission: WC T-5
Axle/Gears: 4.10 LSD
FS/FT: Midwest Motorsports Forged 355 -0 Miles- Perfect For Boost! IOWA $1500
$1500 Or Trade for lower mileage 5.7 TPI + 5 Speed/700r4
First off The engine was professionally built/assembled by Midwest Motorsports in Ames,Iowa - And I do have all the build/parts receits except for the crank. The engine is basicly new outside of the shrink-wrap and crate. Here's the specs.
1979 350 4 Bolt Main Block Bored And Honed .030 Over
The block was magnafluxed and hot tanked.
The Oil Galleries and pickup were de-burred for better flowing.
After everything checked out, here's what was installed.
Wiseco Forged Pistons - 8.5-1 Compression Ratio - Blower Rings
Eagle Forged "3D" H-Beam Rods - Rated For Over 700HP
Eagle Forged Crank - Looking For Receipt.
GM "487" Heads - 2.02/1.60 SS Valves - 1.6 Ratio Prowler RR's
Slight Port And Polish Job - 76cc chambers - Crane .500 Springs
New 7 Quart Oil Pan
Crane Xtreme Engery Cam - 2800-5800 Range
Comp Pushrods
Alluminum Pulleys
Alluminum Water Pump
Moroso Chrome Air Cleaner
Chrome Valve Covers
Chrome Dipstick
Unknown Balancer - Looks New
You also get the nice stand it sits in! What a deal ;oD
Engine does not include intake manifold/carb/distrib.
I'm trying to describe this motor the best I can, I dont have all the papers in front of me so this is all off the top of my head but atleast you know the basics, any questions just shoot me a PM or e-mail me at my address below.
The only bad thing about the motor is on the outside of the heads there is some surface rust from sitting, easily sanded off (I may do it anyway before buyer picks up motor)
Like I said just shoot me offers or any trades you have in mind.
Sorry for the bad pic quality, I'm gonna try and see if I can get some better ones took.
Thanks.
Chris
NitrousJunkie427@wmconnect.com
First off The engine was professionally built/assembled by Midwest Motorsports in Ames,Iowa - And I do have all the build/parts receits except for the crank. The engine is basicly new outside of the shrink-wrap and crate. Here's the specs.
1979 350 4 Bolt Main Block Bored And Honed .030 Over
The block was magnafluxed and hot tanked.
The Oil Galleries and pickup were de-burred for better flowing.
After everything checked out, here's what was installed.
Wiseco Forged Pistons - 8.5-1 Compression Ratio - Blower Rings
Eagle Forged "3D" H-Beam Rods - Rated For Over 700HP
Eagle Forged Crank - Looking For Receipt.
GM "487" Heads - 2.02/1.60 SS Valves - 1.6 Ratio Prowler RR's
Slight Port And Polish Job - 76cc chambers - Crane .500 Springs
New 7 Quart Oil Pan
Crane Xtreme Engery Cam - 2800-5800 Range
Comp Pushrods
Alluminum Pulleys
Alluminum Water Pump
Moroso Chrome Air Cleaner
Chrome Valve Covers
Chrome Dipstick
Unknown Balancer - Looks New
You also get the nice stand it sits in! What a deal ;oD
Engine does not include intake manifold/carb/distrib.
I'm trying to describe this motor the best I can, I dont have all the papers in front of me so this is all off the top of my head but atleast you know the basics, any questions just shoot me a PM or e-mail me at my address below.
The only bad thing about the motor is on the outside of the heads there is some surface rust from sitting, easily sanded off (I may do it anyway before buyer picks up motor)
Like I said just shoot me offers or any trades you have in mind.
Sorry for the bad pic quality, I'm gonna try and see if I can get some better ones took.
Thanks.
Chris
NitrousJunkie427@wmconnect.com
Last edited by WickedZ; 08-01-2005 at 10:05 AM.
Thread
Thread Starter
Forum
Replies
Last Post
codeysabatini
Engine/Drivetrain/Suspension Parts for Sale
5
11-10-2015 04:07 PM
blackandblue02
Camaros for Sale
0
09-10-2015 08:19 PM
Andrew Prakash
TPI
2
09-08-2015 11:48 AM