Where did my Clock/Display Go?
05-10-2002, 04:10 PM
#1
Junior Member
Thread Starter
Join Date: Oct 2001
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: '86 IROC Z
Engine: 305 Tpi
Transmission: 700R4
Where did my Clock/Display Go?
Hey Guys,
I have just re-fitted my original GM Delco Radio (not Radio Cassette) into my '86 'roc.
I had my Radio on but it was getting dark outside so I switched my lights on...........
............and my Radio Display went awol - I was still getting tunes but no Clock or Frequency Display.
I managed to get a set of block connectors from a junk yard so that I could re-install the original Radio. (the previous owner must have thrown the original connector plugs away I guess)
I spliced all the appropriate wires back together from the harness to the connector plugs from the junk yard (quite easy because they were color coded etc)
The Radio barked into life without problems until the lights go on!
I have a wire spare (which is Grey or Gray? I think) that runs from the junk yard Radio Connector Block (marked "Lamp" on the Radio Case) but dosen't seem to have a corresponding wire on the car harness to splice to.
I think this wire not being connected is my problem
Anybody got any ideas?
I have just re-fitted my original GM Delco Radio (not Radio Cassette) into my '86 'roc.
I had my Radio on but it was getting dark outside so I switched my lights on...........
............and my Radio Display went awol - I was still getting tunes but no Clock or Frequency Display.
I managed to get a set of block connectors from a junk yard so that I could re-install the original Radio. (the previous owner must have thrown the original connector plugs away I guess)
I spliced all the appropriate wires back together from the harness to the connector plugs from the junk yard (quite easy because they were color coded etc)
The Radio barked into life without problems until the lights go on!
I have a wire spare (which is Grey or Gray? I think) that runs from the junk yard Radio Connector Block (marked "Lamp" on the Radio Case) but dosen't seem to have a corresponding wire on the car harness to splice to.
I think this wire not being connected is my problem
Anybody got any ideas?
05-10-2002, 07:22 PM
#2
Supreme Member
Join Date: Jul 1999
Location: USA
Posts: 1,405
Received 0 Likes
on
0 Posts
Car: 1988 IROC-Z
Engine: 5.7L TPI
Transmission: 700R4
Axle/Gears: BW 2.77
Sounds like you're on track.
By looking at the photo, the grey wire is for Lights On Input, which (I think) then uses power (or input) from the Lights Dimmer input (brown).
I had a similar problem because somehow I crossed the two (confused I guess) when installing the newer deck. I'm pretty sure you need both wires.
By looking at the photo, the grey wire is for Lights On Input, which (I think) then uses power (or input) from the Lights Dimmer input (brown).
I had a similar problem because somehow I crossed the two (confused I guess) when installing the newer deck. I'm pretty sure you need both wires.
05-12-2002, 04:28 AM
#4
Junior Member
Thread Starter
Join Date: Oct 2001
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: '86 IROC Z
Engine: 305 Tpi
Transmission: 700R4
Hey Allan,
That wiring diagram is the business and I have now wired up the offending Gray/Grey wire to the dimmer connector and my diplay is back off holiday!
Thanks for your help.
That wiring diagram is the business and I have now wired up the offending Gray/Grey wire to the dimmer connector and my diplay is back off holiday!
Thanks for your help.
