Search



Go Back   Third Generation F-Body Message Boards > Tech Boards > Fabrication
Register Forgot Password?

Fabrication Custom fabrication ideas and concepts ranging from body kits, interior work, driveline tech, and much more.

Welcome to ThirdGen.org!
Welcome to ThirdGen.org.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join the ThirdGen.org community today!


Reply
 
Thread Tools Search this Thread
Old 05-16-2010, 08:58 PM   #1
Junior Member
 
Bota 65's Avatar
 
Join Date: Feb 2010
Location: Independence, MO
Posts: 56
Car: 1987 Formula
Engine: 350 TPI
Transmission: 700 R4
Axle/Gears: 3.42 L/S

Classifieds Rating: (0)
Adjusting Doors?

Sorry if this sounds dumb but i need to know how to adjust my drivers door. It is down just a hair and i have no idea how to line it up. Any advice on how to dothis would be greatly appreciated.
Bota 65 is offline vBGarage Page   Reply With Quote
Old 05-16-2010, 09:28 PM   #2
Senior Member
 
Drew's Avatar
 
Join Date: Jul 1999
Posts: 12,324

Classifieds Rating: (14)
Re: Adjusting Doors?

There are three bolts in the top hinge and three in the bottom hinge, both on the car side of the hinge. A couple of them are accessible through the front wheel well with the liner removed, the rest are accessible with the kickpanels removed from the interior.

If the doors have never been off, chances are your hinges are just sagging. A search should find a ton of threads with solutions.
__________________
Drew
83 Camaro 5.0L *1995-98* RIP
84 Camaro 2.8L *2005-06* RIP
86 Trans Am WS6 5.7L Sold!
86 Mustang 2.3L Turbo
87 Iroc 5.7L
91 Formula 5.7L
91 Camaro RS convertible 5.0L
91 Firebird 3.1L *1999-06* Sold!
Drew is offline vBGarage Page   Reply With Quote
Old 05-24-2010, 04:01 AM   #3
Member
 
stealthroc89's Avatar
 
Join Date: May 2010
Location: Houston Area
Posts: 463
Car: 1989 IROC-Z
Engine: 355, 6.0 (LQ4) soon
Transmission: 700R4
Axle/Gears: Borg Warner 2.77 for now

Classifieds Rating: (0)
Re: Adjusting Doors?

Its been a while since ive done it but if I remember correctly, remove the middle bolt from the upper and lower hinges, have a buddy or a jack (i used a jack) hold the door up at the end with a little pressure. Barely loosen the remaining 4 bolts and lift the door just a little. Tighten the bolts and carefully close the door. Keep repeating this till its where you want it. The 2 bolts you took out more than likely are not going to go back in cause the counter bore in the hinge is only big enough for the bolt to pass through. I did this a year ago and I havent had any problems with the doors since I did it. Although it isnt reccomended to leave out bolts I did it with very good results. U can go as far as making the hole bigger to allow for the adjustment. Its very good if your on a budget
stealthroc89 is offline vBGarage Page   Reply With Quote
Old 05-24-2010, 05:33 AM   #4
Junior Member
 
Bota 65's Avatar
 
Join Date: Feb 2010
Location: Independence, MO
Posts: 56
Car: 1987 Formula
Engine: 350 TPI
Transmission: 700 R4
Axle/Gears: 3.42 L/S

Classifieds Rating: (0)
Re: Adjusting Doors?

Ok thanks, i'll check into that.
Bota 65 is offline vBGarage Page   Reply With Quote
Old 05-24-2010, 05:33 AM
ThirdGen
1992 Camaro




Paid Advertisement


Reply

Go Back   Third Generation F-Body Message Boards > Tech Boards > Fabrication

Tags
1992, 91, adjust, adjusting, ajusting, camaro, door, doors, fbody, generation, hinges, iroc, irocz, org, thirdgen, trans
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


1982 Camaro '82 || 1983 Camaro '83 || 1984 Camaro '84 || 1985 Camaro '85 || 1986 Camaro '86 || 1987 Camaro '87 || 1988 Camaro '88 || 1989 Camaro '89 || 1990 Camaro '90 || 1991 Camaro '91 || 1992 Camaro '92


All times are GMT -5. The time now is 04:39 PM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.5.2
All content copyright 1997 - 2014 ThirdGen.org. All rights reserved. No part of this website may be reproduced without the expressed, documented, and written consent of ThirdGen.org's Administrators.

Emails & Contact Details