87 GTA roller/finisher
#1
Member
Thread Starter
iTrader: (2)
Join Date: Jul 2000
Location: helldon, fl
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 trans am GTA
Engine: tesla permanent magnet
Transmission: 93 T-56
Axle/Gears: moser 12bolt w/ 3.73
87 GTA roller/finisher
FLORIDA, RUSKIN area ,
87 gta needs paint and minor body work; dings dents that kinda stuff
rear end: fairly new moser 12 bolt 3.73, with LS1 brakes, spohn LCA's, Lakewood panhard, airbag on right spring
trans:rebuilt M66 T56 (3.36 1ST gear) slp shifter, centerforce billet fly wheel and dual friction clutch pack
Motor: !not in car! gmpp 4bolt long block (NF crank, powered rods, lt1 pistons)
topped with GMPP fast burn heads *BRANDNEW*
Whats in boxes:
bigbrake.com LS1 front brake kits (knuckles and all)
ACCEL 74219 cam (.525lift)
timing gear
comp cams roller lifters
roll control
1.75 longtubes
dual 3" exhuast
INTAKE AND FUEL:
Super ram assembly
30lb inj
58mm
ported mafs
4" ducting and lt1 elbow
255lph pump
time, finances, and lack of facilities forces this sale... ive had the car since highschool and know what i have into it and what it could be if finished, so basicly dont waste my time with bullshit offers and stupid trades, only reasonable offers please
mike
87 gta needs paint and minor body work; dings dents that kinda stuff
rear end: fairly new moser 12 bolt 3.73, with LS1 brakes, spohn LCA's, Lakewood panhard, airbag on right spring
trans:rebuilt M66 T56 (3.36 1ST gear) slp shifter, centerforce billet fly wheel and dual friction clutch pack
Motor: !not in car! gmpp 4bolt long block (NF crank, powered rods, lt1 pistons)
topped with GMPP fast burn heads *BRANDNEW*
Whats in boxes:
bigbrake.com LS1 front brake kits (knuckles and all)
ACCEL 74219 cam (.525lift)
timing gear
comp cams roller lifters
roll control
1.75 longtubes
dual 3" exhuast
INTAKE AND FUEL:
Super ram assembly
30lb inj
58mm
ported mafs
4" ducting and lt1 elbow
255lph pump
time, finances, and lack of facilities forces this sale... ive had the car since highschool and know what i have into it and what it could be if finished, so basicly dont waste my time with bullshit offers and stupid trades, only reasonable offers please
mike
#2
TGO Supporter
iTrader: (2)
Join Date: Feb 2000
Location: Avatar: My 34' 1989 Scarab III w/ twin 454's (502's Started!)
Posts: 1,235
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1989 Wellcraft Scarab III
Engine: Twin 454's
Axle/Gears: Twin Mercruiser Bravo I's
Re: 87 GTA roller/finisher
FLORIDA, RUSKIN area ,
87 gta needs paint and minor body work; dings dents that kinda stuff
rear end: fairly new moser 12 bolt 3.73, with LS1 brakes, spohn LCA's, Lakewood panhard, airbag on right spring
trans:rebuilt M66 T56 (3.36 1ST gear) slp shifter, centerforce billet fly wheel and dual friction clutch pack
Motor: !not in car! gmpp 4bolt long block (NF crank, powered rods, lt1 pistons)
topped with GMPP fast burn heads *BRANDNEW*
Whats in boxes:
bigbrake.com LS1 front brake kits (knuckles and all)
ACCEL 74219 cam (.525lift)
timing gear
comp cams roller lifters
roll control
1.75 longtubes
dual 3" exhuast
INTAKE AND FUEL:
Super ram assembly
30lb inj
58mm
ported mafs
4" ducting and lt1 elbow
255lph pump
time, finances, and lack of facilities forces this sale... ive had the car since highschool and know what i have into it and what it could be if finished, so basicly dont waste my time with bullshit offers and stupid trades, only reasonable offers please
mike
87 gta needs paint and minor body work; dings dents that kinda stuff
rear end: fairly new moser 12 bolt 3.73, with LS1 brakes, spohn LCA's, Lakewood panhard, airbag on right spring
trans:rebuilt M66 T56 (3.36 1ST gear) slp shifter, centerforce billet fly wheel and dual friction clutch pack
Motor: !not in car! gmpp 4bolt long block (NF crank, powered rods, lt1 pistons)
topped with GMPP fast burn heads *BRANDNEW*
Whats in boxes:
bigbrake.com LS1 front brake kits (knuckles and all)
ACCEL 74219 cam (.525lift)
timing gear
comp cams roller lifters
roll control
1.75 longtubes
dual 3" exhuast
INTAKE AND FUEL:
Super ram assembly
30lb inj
58mm
ported mafs
4" ducting and lt1 elbow
255lph pump
time, finances, and lack of facilities forces this sale... ive had the car since highschool and know what i have into it and what it could be if finished, so basicly dont waste my time with bullshit offers and stupid trades, only reasonable offers please
mike
#4
Junior Member
Join Date: Dec 2010
Location: West Lafayette IN
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 iroc convertable/ 84 z 12 sec
Engine: stock 305 tpi/ 383
Transmission: 700r4
Axle/Gears: 3.73
Re: 87 GTA roller/finisher
might be interested in rear if you still have it
Thread
Thread Starter
Forum
Replies
Last Post