350 Vortec long block zero miles
#1
Senior Member
Thread Starter
Join Date: Dec 2000
Location: El Paso Texas
Posts: 640
Received 0 Likes
on
0 Posts
Car: 86 z28
Engine: Hyd. roller 498
Transmission: 700r4
Axle/Gears: 12 bolt 3.90 gears
350 Vortec long block zero miles
This engine has never been run before, it includes a polished vortec intake, flowtech long tube headers , new timing chain cover, 1 piece felpro oil pan gasket, new oil pan, flexplate included. Pistons are flat tops 040, cam is an "RV" type . This engine was setup for a 4x4 meaning=low end torque. Note u would have to go through break in procedure . Asking $800 Rob NOte : have no idea on shipping , I'll go halfers me zip code is 79838 email or pm
#3
Senior Member
Thread Starter
Join Date: Dec 2000
Location: El Paso Texas
Posts: 640
Received 0 Likes
on
0 Posts
Car: 86 z28
Engine: Hyd. roller 498
Transmission: 700r4
Axle/Gears: 12 bolt 3.90 gears
Without headers and flexplate I'll go $700. Also something real important that I left out is that, this intake is for a carb.
#4
Member
Join Date: Oct 2002
Location: memphis
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
Car: 67 camaro ( project )
Engine: 6.7 408 n a snail
Transmission: 4l80 - stalled
Axle/Gears: 3.25 - narrowd tci kit 9 inch
what flowtech long tubes are these? the ones for camaro? if so how much w/ shipping to 38115 and its a buisness not a residental addy so it should cost less. also please post a pic of them, thanks! or email it to me vladicore@hotmail.com
#7
Senior Member
Thread Starter
Join Date: Dec 2000
Location: El Paso Texas
Posts: 640
Received 0 Likes
on
0 Posts
Car: 86 z28
Engine: Hyd. roller 498
Transmission: 700r4
Axle/Gears: 12 bolt 3.90 gears
Originally posted by vladicore
what flowtech long tubes are these? the ones for camaro? if so how much w/ shipping to 38115 and its a buisness not a residental addy so it should cost less. also please post a pic of them, thanks! or email it to me vladicore@hotmail.com
what flowtech long tubes are these? the ones for camaro? if so how much w/ shipping to 38115 and its a buisness not a residental addy so it should cost less. also please post a pic of them, thanks! or email it to me vladicore@hotmail.com
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Dec 2000
Location: El Paso Texas
Posts: 640
Received 0 Likes
on
0 Posts
Car: 86 z28
Engine: Hyd. roller 498
Transmission: 700r4
Axle/Gears: 12 bolt 3.90 gears
Originally posted by daturbosix
too bad your not closer to chicago.... unless you'd be willing to ship?
too bad your not closer to chicago.... unless you'd be willing to ship?
#9
Senior Member
Thread Starter
Join Date: Dec 2000
Location: El Paso Texas
Posts: 640
Received 0 Likes
on
0 Posts
Car: 86 z28
Engine: Hyd. roller 498
Transmission: 700r4
Axle/Gears: 12 bolt 3.90 gears
Originally posted by IROCBUFF
Are you taking a Vortec TPI manifold or carb?
Are you taking a Vortec TPI manifold or carb?
Thread
Thread Starter
Forum
Replies
Last Post
theshackle
Tech / General Engine
4
03-05-2017 06:37 PM
Fast355
DFI and ECM
14
12-02-2016 06:33 PM