3.73 disc brake auburn posi rear end for sale
#1
Want a title? Post!
Thread Starter
Join Date: Feb 2003
Location: Indianapolis, Indiana
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Car: 93 T/A - 87 LX
3.73 disc brake auburn posi rear end for sale
For sale: 3.73:1 from 88 iroc, has disc brakes with all brake hardware including callipers and ebrake cables. It was rebuilt by titus transmission a couple years ago, but was only drove roughly 5k miles. I took it out to put in my T/A and ended up using a different rear end because it doesn't have abs sensor and have since sold the camaro it came out of. it has an aubrun posi carrier and the axles were replaced by titus. LOCAL pick up only INDIANAPOLIS AREA Needs to get out of my garage... make offer
thanks
steve
317-250-6686
slsjr1@yahoo.com
thanks
steve
317-250-6686
slsjr1@yahoo.com
#2
Member
Join Date: Oct 2005
Location: OKLAHOMA
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 CAMARO
Engine: 434
Transmission: th400 rmvb,nc 4500 stall
Axle/Gears: MOSER 12BOLT,35splineaxels,4.33gear
is it a 10 bolt or a 9 bolt? are all the internal stock or are they
aftermarket?
and would you be willling to ship?
aftermarket?
and would you be willling to ship?
Last edited by ONEFASTZ; 01-11-2006 at 02:44 PM.
#3
Member
Join Date: Dec 2003
Location: Va
Posts: 192
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 camaro
Engine: 355
Transmission: 700r4
I am very intrested but i need a pic of the rear and some info also to make an offer. Such as % of pads/rotors remaining type of gears etc. Also is this rear from a thirdgen because to me it sounds like you have a forth gen. This is important because 4th gen rears stick out alittle more then a typical thridgen would. Thanks,
Jason
Jason
Last edited by Toxinz; 01-11-2006 at 03:07 PM.
#4
Want a title? Post!
Thread Starter
Join Date: Feb 2003
Location: Indianapolis, Indiana
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Car: 93 T/A - 87 LX
LOCAL PICKUP ONLY
I will get pictures on friday.
it is out of a 3rd gen, I was going to put it in a 4thgen, but didn't have abs sensor...
I will get pictures on friday.
it is out of a 3rd gen, I was going to put it in a 4thgen, but didn't have abs sensor...
#5
Want a title? Post!
Thread Starter
Join Date: Feb 2003
Location: Indianapolis, Indiana
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
Car: 93 T/A - 87 LX
measurements
Here are some general pics, I have more, plus here are the measurements since some have asked for this:
rotor to rotor 61" +1 inch on each side (studs) 59 1/4" from surface to surface.
40" in center to center spring cups
40 1/2" from shock mount to shock mount
ctrl arm 42 1/4" inside to inside 47 1/4" from outside to outside
it has
GM N
22522676
on the case
thanks
steve
rotor to rotor 61" +1 inch on each side (studs) 59 1/4" from surface to surface.
40" in center to center spring cups
40 1/2" from shock mount to shock mount
ctrl arm 42 1/4" inside to inside 47 1/4" from outside to outside
it has
GM N
22522676
on the case
thanks
steve
Thread
Thread Starter
Forum
Replies
Last Post
hectre13
Engine/Drivetrain/Suspension Parts for Sale
2
12-11-2023 08:14 AM
hectre13
Engine/Drivetrain/Suspension Parts for Sale
7
08-26-2015 08:17 AM
AkDrifted
Engine/Drivetrain/Suspension Parts for Sale
6
08-17-2015 07:45 PM
novaderrik
Transmissions and Drivetrain
3
08-10-2015 12:44 PM
1992 Trans Am
Engine/Drivetrain/Suspension Parts for Sale
1
08-08-2015 08:16 PM