Denny's Driveshaft - HD Alum MMC for sale
04-20-2006, 07:01 PM
#1
Senior Member
Thread Starter
iTrader: (2)
Join Date: Aug 1999
Location: Elkton MD, USA
Posts: 858
Likes: 0
Received 5 Likes
on
3 Posts
Car: 1985 Camaro Z28, VIN F
Engine: 427 sbc, HSR
Transmission: T-56, self rebuilt 700+ hp
Axle/Gears: Moser 12bolt, 3.42 trutrac
Denny's Driveshaft - HD Alum MMC for sale
041129dennyDS
Bought this for my car last year, but now it's too long for the 12bolt. It's designed for
cars with 44-7/8" between trans tail face, and Pinion face. I ran it on my 10-bolt rear
and T56 trans. It has 1350 u-joints, and I can include a 10-bolt 1350-series pinion for
additional cost if needed. (Should work equally well on 3rd/4th gens, with T5/T56/700r4/4e60)
Shaft costs over $550 new (I know because I just ordered a new one to replace it)
and I'm asking $350 + S/H for it. It has 1 small rub ring where the rubber ebrake cable was
resting on it for a short time, but only cosmetic.
Dennys Driveshaft HD Aluminum Driveshafts for your street rod or race car MMC tubing
Bought this for my car last year, but now it's too long for the 12bolt. It's designed for
cars with 44-7/8" between trans tail face, and Pinion face. I ran it on my 10-bolt rear
and T56 trans. It has 1350 u-joints, and I can include a 10-bolt 1350-series pinion for
additional cost if needed. (Should work equally well on 3rd/4th gens, with T5/T56/700r4/4e60)
Shaft costs over $550 new (I know because I just ordered a new one to replace it)
and I'm asking $350 + S/H for it. It has 1 small rub ring where the rubber ebrake cable was
resting on it for a short time, but only cosmetic.
Dennys Driveshaft HD Aluminum Driveshafts for your street rod or race car MMC tubing
05-06-2006, 09:15 AM
#2
Senior Member
Thread Starter
iTrader: (2)
Join Date: Aug 1999
Location: Elkton MD, USA
Posts: 858
Likes: 0
Received 5 Likes
on
3 Posts
Car: 1985 Camaro Z28, VIN F
Engine: 427 sbc, HSR
Transmission: T-56, self rebuilt 700+ hp
Axle/Gears: Moser 12bolt, 3.42 trutrac
Just received my new Dennys HD DS to fit the 12bolt, this one's
out and still available... Make offer
out and still available... Make offer
05-07-2006, 06:40 AM
#4
Senior Member
Thread Starter
iTrader: (2)
Join Date: Aug 1999
Location: Elkton MD, USA
Posts: 858
Likes: 0
Received 5 Likes
on
3 Posts
Car: 1985 Camaro Z28, VIN F
Engine: 427 sbc, HSR
Transmission: T-56, self rebuilt 700+ hp
Axle/Gears: Moser 12bolt, 3.42 trutrac
Originally Posted by a383z
Do you still have the drive shaft available and I live in upper marlboro md maybe I can stop by and take a look.
Thread
Thread Starter
Forum
Replies
Last Post
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
1
11-19-2015 07:03 AM
camaro1185
Engine/Drivetrain/Suspension Parts for Sale
4
10-26-2015 06:51 AM